Quelltext /~heha/mb-iwp/Anzeige mit VQC10/Firmware.zip/msp430x552x.h

/******************************************************************************/
/* Legacy Header File                                                         */
/* Not recommended for use in new projects.                                   */
/* Please use the msp430.h file or the device specific header file            */
/******************************************************************************/

/********************************************************************
*
* Standard register and bit definitions for the Texas Instruments
* MSP430 microcontroller.
*
* This file supports assembler and C development for
* msp430x552x devices.
*
* Texas Instruments, Version 1.3
*
* Rev. 1.0, Setup
* Rev. 1.1, Fixed Error in DMA Trigger Definitons
* Rev. 1.2, fixed SYSUNIV_BUSIFG definition
*           fixed wrong bit definition in PM5CTL0 (LOCKLPM5)
* Rev. 1.3, Changed access type of DMAxSZ registers to word only
*
********************************************************************/

#ifndef __msp430x552x
#define __msp430x552x

#define __MSP430_TI_HEADERS__ 

#include "iomacros.h"

/************************************************************
* STANDARD BITS
************************************************************/

#define BIT0		0x0001
#define BIT1		0x0002
#define BIT2		0x0004
#define BIT3		0x0008
#define BIT4		0x0010
#define BIT5		0x0020
#define BIT6		0x0040
#define BIT7		0x0080
#define BIT8		0x0100
#define BIT9		0x0200
#define BITA		0x0400
#define BITB		0x0800
#define BITC		0x1000
#define BITD		0x2000
#define BITE		0x4000
#define BITF		0x8000

/************************************************************
* STATUS REGISTER BITS
************************************************************/

#define C		0x0001
#define Z		0x0002
#define N		0x0004
#define V		0x0100
#define GIE		0x0008
#define CPUOFF		0x0010
#define OSCOFF		0x0020
#define SCG0		0x0040
#define SCG1		0x0080

/* Low Power Modes coded with Bits 4-7 in SR */

#ifndef __STDC__ /* Begin #defines for assembler */
#define LPM0		CPUOFF
#define LPM1		(SCG0+CPUOFF)
#define LPM2		(SCG1+CPUOFF)
#define LPM3		(SCG1+SCG0+CPUOFF)
#define LPM4		(SCG1+SCG0+OSCOFF+CPUOFF)
/* End #defines for assembler */

#else /* Begin #defines for C */
#define LPM0_bits	CPUOFF
#define LPM1_bits	(SCG0+CPUOFF)
#define LPM2_bits	(SCG1+CPUOFF)
#define LPM3_bits	(SCG1+SCG0+CPUOFF)
#define LPM4_bits	(SCG1+SCG0+OSCOFF+CPUOFF)

#define LPM0      _BIS_SR(LPM0_bits)     /* Enter Low Power Mode 0 */
#define LPM0_EXIT _BIC_SR_IRQ(LPM0_bits) /* Exit Low Power Mode 0 */
#define LPM1      _BIS_SR(LPM1_bits)     /* Enter Low Power Mode 1 */
#define LPM1_EXIT _BIC_SR_IRQ(LPM1_bits) /* Exit Low Power Mode 1 */
#define LPM2      _BIS_SR(LPM2_bits)     /* Enter Low Power Mode 2 */
#define LPM2_EXIT _BIC_SR_IRQ(LPM2_bits) /* Exit Low Power Mode 2 */
#define LPM3      _BIS_SR(LPM3_bits)     /* Enter Low Power Mode 3 */
#define LPM3_EXIT _BIC_SR_IRQ(LPM3_bits) /* Exit Low Power Mode 3 */
#define LPM4      _BIS_SR(LPM4_bits)     /* Enter Low Power Mode 4 */
#define LPM4_EXIT _BIC_SR_IRQ(LPM4_bits) /* Exit Low Power Mode 4 */
#endif /* End #defines for C */

/************************************************************
* CPU
************************************************************/
#define __MSP430_HAS_MSP430XV2_CPU__  /* Definition to show that it has MSP430XV2 CPU */

/************************************************************
* PERIPHERAL FILE MAP
************************************************************/


/************************************************************
* ADC12 PLUS
************************************************************/
#define __MSP430_HAS_ADC12_PLUS__     /* Definition to show that Module is available */

#define ADC12CTL0_            0x0700    /* ADC12+ Control 0 */
sfrb(ADC12CTL0_L, ADC12CTL0_);
sfrb(ADC12CTL0_H, ADC12CTL0_+1);
sfrw(ADC12CTL0, ADC12CTL0_);
#define ADC12CTL1_            0x0702    /* ADC12+ Control 1 */
sfrb(ADC12CTL1_L, ADC12CTL1_);
sfrb(ADC12CTL1_H, ADC12CTL1_+1);
sfrw(ADC12CTL1, ADC12CTL1_);
#define ADC12CTL2_            0x0704    /* ADC12+ Control 2 */
sfrb(ADC12CTL2_L, ADC12CTL2_);
sfrb(ADC12CTL2_H, ADC12CTL2_+1);
sfrw(ADC12CTL2, ADC12CTL2_);
#define ADC12IFG_             0x070A    /* ADC12+ Interrupt Flag */
sfrb(ADC12IFG_L, ADC12IFG_);
sfrb(ADC12IFG_H, ADC12IFG_+1);
sfrw(ADC12IFG, ADC12IFG_);
#define ADC12IE_              0x070C    /* ADC12+ Interrupt Enable */
sfrb(ADC12IE_L, ADC12IE_);
sfrb(ADC12IE_H, ADC12IE_+1);
sfrw(ADC12IE, ADC12IE_);
#define ADC12IV_              0x070E    /* ADC12+ Interrupt Vector Word */
sfrb(ADC12IV_L, ADC12IV_);
sfrb(ADC12IV_H, ADC12IV_+1);
sfrw(ADC12IV, ADC12IV_);

#define ADC12MEM0_            0x0720    /* ADC12 Conversion Memory 0 */
sfrb(ADC12MEM0_L, ADC12MEM0_);
sfrb(ADC12MEM0_H, ADC12MEM0_+1);
sfrw(ADC12MEM0, ADC12MEM0_);
#define ADC12MEM1_            0x0722    /* ADC12 Conversion Memory 1 */
sfrb(ADC12MEM1_L, ADC12MEM1_);
sfrb(ADC12MEM1_H, ADC12MEM1_+1);
sfrw(ADC12MEM1, ADC12MEM1_);
#define ADC12MEM2_            0x0724    /* ADC12 Conversion Memory 2 */
sfrb(ADC12MEM2_L, ADC12MEM2_);
sfrb(ADC12MEM2_H, ADC12MEM2_+1);
sfrw(ADC12MEM2, ADC12MEM2_);
#define ADC12MEM3_            0x0726    /* ADC12 Conversion Memory 3 */
sfrb(ADC12MEM3_L, ADC12MEM3_);
sfrb(ADC12MEM3_H, ADC12MEM3_+1);
sfrw(ADC12MEM3, ADC12MEM3_);
#define ADC12MEM4_            0x0728    /* ADC12 Conversion Memory 4 */
sfrb(ADC12MEM4_L, ADC12MEM4_);
sfrb(ADC12MEM4_H, ADC12MEM4_+1);
sfrw(ADC12MEM4, ADC12MEM4_);
#define ADC12MEM5_            0x072A    /* ADC12 Conversion Memory 5 */
sfrb(ADC12MEM5_L, ADC12MEM5_);
sfrb(ADC12MEM5_H, ADC12MEM5_+1);
sfrw(ADC12MEM5, ADC12MEM5_);
#define ADC12MEM6_            0x072C    /* ADC12 Conversion Memory 6 */
sfrb(ADC12MEM6_L, ADC12MEM6_);
sfrb(ADC12MEM6_H, ADC12MEM6_+1);
sfrw(ADC12MEM6, ADC12MEM6_);
#define ADC12MEM7_            0x072E    /* ADC12 Conversion Memory 7 */
sfrb(ADC12MEM7_L, ADC12MEM7_);
sfrb(ADC12MEM7_H, ADC12MEM7_+1);
sfrw(ADC12MEM7, ADC12MEM7_);
#define ADC12MEM8_            0x0730    /* ADC12 Conversion Memory 8 */
sfrb(ADC12MEM8_L, ADC12MEM8_);
sfrb(ADC12MEM8_H, ADC12MEM8_+1);
sfrw(ADC12MEM8, ADC12MEM8_);
#define ADC12MEM9_            0x0732    /* ADC12 Conversion Memory 9 */
sfrb(ADC12MEM9_L, ADC12MEM9_);
sfrb(ADC12MEM9_H, ADC12MEM9_+1);
sfrw(ADC12MEM9, ADC12MEM9_);
#define ADC12MEM10_           0x0734    /* ADC12 Conversion Memory 10 */
sfrb(ADC12MEM10_L, ADC12MEM10_);
sfrb(ADC12MEM10_H, ADC12MEM10_+1);
sfrw(ADC12MEM10, ADC12MEM10_);
#define ADC12MEM11_           0x0736    /* ADC12 Conversion Memory 11 */
sfrb(ADC12MEM11_L, ADC12MEM11_);
sfrb(ADC12MEM11_H, ADC12MEM11_+1);
sfrw(ADC12MEM11, ADC12MEM11_);
#define ADC12MEM12_           0x0738    /* ADC12 Conversion Memory 12 */
sfrb(ADC12MEM12_L, ADC12MEM12_);
sfrb(ADC12MEM12_H, ADC12MEM12_+1);
sfrw(ADC12MEM12, ADC12MEM12_);
#define ADC12MEM13_           0x073A    /* ADC12 Conversion Memory 13 */
sfrb(ADC12MEM13_L, ADC12MEM13_);
sfrb(ADC12MEM13_H, ADC12MEM13_+1);
sfrw(ADC12MEM13, ADC12MEM13_);
#define ADC12MEM14_           0x073C    /* ADC12 Conversion Memory 14 */
sfrb(ADC12MEM14_L, ADC12MEM14_);
sfrb(ADC12MEM14_H, ADC12MEM14_+1);
sfrw(ADC12MEM14, ADC12MEM14_);
#define ADC12MEM15_           0x073E    /* ADC12 Conversion Memory 15 */
sfrb(ADC12MEM15_L, ADC12MEM15_);
sfrb(ADC12MEM15_H, ADC12MEM15_+1);
sfrw(ADC12MEM15, ADC12MEM15_);
#define ADC12MEM_	ADC12MEM  /* ADC12 Conversion Memory */
#ifndef __STDC__
#define ADC12MEM	ADC12MEM0 /* ADC12 Conversion Memory (for assembler) */
#else
#define ADC12MEM	((volatile int*) &ADC12MEM0) /* ADC12 Conversion Memory (for C) */
#endif

#define ADC12MCTL0_	0x0710    /* ADC12 Memory Control 0 */
sfrb(ADC12MCTL0, ADC12MCTL0_);
#define ADC12MCTL1_	0x0711    /* ADC12 Memory Control 1 */
sfrb(ADC12MCTL1, ADC12MCTL1_);
#define ADC12MCTL2_	0x0712    /* ADC12 Memory Control 2 */
sfrb(ADC12MCTL2, ADC12MCTL2_);
#define ADC12MCTL3_	0x0713    /* ADC12 Memory Control 3 */
sfrb(ADC12MCTL3, ADC12MCTL3_);
#define ADC12MCTL4_	0x0714    /* ADC12 Memory Control 4 */
sfrb(ADC12MCTL4, ADC12MCTL4_);
#define ADC12MCTL5_	0x0715    /* ADC12 Memory Control 5 */
sfrb(ADC12MCTL5, ADC12MCTL5_);
#define ADC12MCTL6_	0x0716    /* ADC12 Memory Control 6 */
sfrb(ADC12MCTL6, ADC12MCTL6_);
#define ADC12MCTL7_	0x0717    /* ADC12 Memory Control 7 */
sfrb(ADC12MCTL7, ADC12MCTL7_);
#define ADC12MCTL8_	0x0718    /* ADC12 Memory Control 8 */
sfrb(ADC12MCTL8, ADC12MCTL8_);
#define ADC12MCTL9_	0x0719    /* ADC12 Memory Control 9 */
sfrb(ADC12MCTL9, ADC12MCTL9_);
#define ADC12MCTL10_	0x071A    /* ADC12 Memory Control 10 */
sfrb(ADC12MCTL10, ADC12MCTL10_);
#define ADC12MCTL11_	0x071B    /* ADC12 Memory Control 11 */
sfrb(ADC12MCTL11, ADC12MCTL11_);
#define ADC12MCTL12_	0x071C    /* ADC12 Memory Control 12 */
sfrb(ADC12MCTL12, ADC12MCTL12_);
#define ADC12MCTL13_	0x071D    /* ADC12 Memory Control 13 */
sfrb(ADC12MCTL13, ADC12MCTL13_);
#define ADC12MCTL14_	0x071E    /* ADC12 Memory Control 14 */
sfrb(ADC12MCTL14, ADC12MCTL14_);
#define ADC12MCTL15_	0x071F    /* ADC12 Memory Control 15 */
sfrb(ADC12MCTL15, ADC12MCTL15_);
#define ADC12MCTL_ 	ADC12MCTL /* ADC12 Memory Control */
#ifndef __STDC__
#define ADC12MCTL	ADC12MCTL0 /* ADC12 Memory Control (for assembler) */
#else
#define ADC12MCTL	((volatile char*)ADC12MCTL0) /* ADC12 Memory Control (for C) */
#endif

/* ADC12CTL0 Control Bits */
#define ADC12SC		0x0001  /* ADC12 Start Conversion */
#define ADC12ENC	0x0002  /* ADC12 Enable Conversion */
#define ADC12TOVIE	0x0004  /* ADC12 Timer Overflow interrupt enable */
#define ADC12OVIE	0x0008  /* ADC12 Overflow interrupt enable */
#define ADC12ON		0x0010  /* ADC12 On/enable */
#define ADC12REFON	0x0020  /* ADC12 Reference on */
#define ADC12REF2_5V	0x0040  /* ADC12 Ref 0:1.5V / 1:2.5V */
#define ADC12MSC	0x0080  /* ADC12 Multiple SampleConversion */
#define ADC12SHT00	0x0100  /* ADC12 Sample Hold 0 Select Bit: 0 */
#define ADC12SHT01	0x0200  /* ADC12 Sample Hold 0 Select Bit: 1 */
#define ADC12SHT02	0x0400  /* ADC12 Sample Hold 0 Select Bit: 2 */
#define ADC12SHT03	0x0800  /* ADC12 Sample Hold 0 Select Bit: 3 */
#define ADC12SHT10	0x1000  /* ADC12 Sample Hold 1 Select Bit: 0 */
#define ADC12SHT11	0x2000  /* ADC12 Sample Hold 1 Select Bit: 1 */
#define ADC12SHT12	0x4000  /* ADC12 Sample Hold 1 Select Bit: 2 */
#define ADC12SHT13	0x8000  /* ADC12 Sample Hold 1 Select Bit: 3 */

/* ADC12CTL0 Control Bits */
#define ADC12SC_L           (0x0001)  /* ADC12 Start Conversion */
#define ADC12ENC_L          (0x0002)  /* ADC12 Enable Conversion */
#define ADC12TOVIE_L        (0x0004)  /* ADC12 Timer Overflow interrupt enable */
#define ADC12OVIE_L         (0x0008)  /* ADC12 Overflow interrupt enable */
#define ADC12ON_L           (0x0010)  /* ADC12 On/enable */
#define ADC12REFON_L        (0x0020)  /* ADC12 Reference on */
#define ADC12REF2_5V_L      (0x0040)  /* ADC12 Ref 0:1.5V / 1:2.5V */
#define ADC12MSC_L          (0x0080)  /* ADC12 Multiple SampleConversion */

/* ADC12CTL0 Control Bits */
#define ADC12SHT00_H        (0x0001)  /* ADC12 Sample Hold 0 Select Bit: 0 */
#define ADC12SHT01_H        (0x0002)  /* ADC12 Sample Hold 0 Select Bit: 1 */
#define ADC12SHT02_H        (0x0004)  /* ADC12 Sample Hold 0 Select Bit: 2 */
#define ADC12SHT03_H        (0x0008)  /* ADC12 Sample Hold 0 Select Bit: 3 */
#define ADC12SHT10_H        (0x0010)  /* ADC12 Sample Hold 1 Select Bit: 0 */
#define ADC12SHT11_H        (0x0020)  /* ADC12 Sample Hold 1 Select Bit: 1 */
#define ADC12SHT12_H        (0x0040)  /* ADC12 Sample Hold 1 Select Bit: 2 */
#define ADC12SHT13_H        (0x0080)  /* ADC12 Sample Hold 1 Select Bit: 3 */

#define ADC12SHT0_0         (0*0x100)  /* ADC12 Sample Hold 0 Select Bit: 0 */
#define ADC12SHT0_1         (1*0x100)  /* ADC12 Sample Hold 0 Select Bit: 1 */
#define ADC12SHT0_2         (2*0x100)  /* ADC12 Sample Hold 0 Select Bit: 2 */
#define ADC12SHT0_3         (3*0x100)  /* ADC12 Sample Hold 0 Select Bit: 3 */
#define ADC12SHT0_4         (4*0x100)  /* ADC12 Sample Hold 0 Select Bit: 4 */
#define ADC12SHT0_5         (5*0x100)  /* ADC12 Sample Hold 0 Select Bit: 5 */
#define ADC12SHT0_6         (6*0x100)  /* ADC12 Sample Hold 0 Select Bit: 6 */
#define ADC12SHT0_7         (7*0x100)  /* ADC12 Sample Hold 0 Select Bit: 7 */
#define ADC12SHT0_8         (8*0x100)  /* ADC12 Sample Hold 0 Select Bit: 8 */
#define ADC12SHT0_9         (9*0x100)  /* ADC12 Sample Hold 0 Select Bit: 9 */
#define ADC12SHT0_10        (10*0x100) /* ADC12 Sample Hold 0 Select Bit: 10 */
#define ADC12SHT0_11        (11*0x100) /* ADC12 Sample Hold 0 Select Bit: 11 */
#define ADC12SHT0_12        (12*0x100) /* ADC12 Sample Hold 0 Select Bit: 12 */
#define ADC12SHT0_13        (13*0x100) /* ADC12 Sample Hold 0 Select Bit: 13 */
#define ADC12SHT0_14        (14*0x100) /* ADC12 Sample Hold 0 Select Bit: 14 */
#define ADC12SHT0_15        (15*0x100) /* ADC12 Sample Hold 0 Select Bit: 15 */

#define ADC12SHT1_0         (0U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 0 */
#define ADC12SHT1_1         (1U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 1 */
#define ADC12SHT1_2         (2U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 2 */
#define ADC12SHT1_3         (3U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 3 */
#define ADC12SHT1_4         (4U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 4 */
#define ADC12SHT1_5         (5U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 5 */
#define ADC12SHT1_6         (6U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 6 */
#define ADC12SHT1_7         (7U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 7 */
#define ADC12SHT1_8         (8U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 8 */
#define ADC12SHT1_9         (9U*0x1000)  /* ADC12 Sample Hold 1 Select Bit: 9 */
#define ADC12SHT1_10        (10U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 10 */
#define ADC12SHT1_11        (11U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 11 */
#define ADC12SHT1_12        (12U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 12 */
#define ADC12SHT1_13        (13U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 13 */
#define ADC12SHT1_14        (14U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 14 */
#define ADC12SHT1_15        (15U*0x1000) /* ADC12 Sample Hold 1 Select Bit: 15 */

/* ADC12CTL1 Control Bits */
#define ADC12BUSY           (0x0001)    /* ADC12 Busy */
#define ADC12CONSEQ0        (0x0002)    /* ADC12 Conversion Sequence Select Bit: 0 */
#define ADC12CONSEQ1        (0x0004)    /* ADC12 Conversion Sequence Select Bit: 1 */
#define ADC12SSEL0          (0x0008)    /* ADC12 Clock Source Select Bit: 0 */
#define ADC12SSEL1          (0x0010)    /* ADC12 Clock Source Select Bit: 1 */
#define ADC12DIV0           (0x0020)    /* ADC12 Clock Divider Select Bit: 0 */
#define ADC12DIV1           (0x0040)    /* ADC12 Clock Divider Select Bit: 1 */
#define ADC12DIV2           (0x0080)    /* ADC12 Clock Divider Select Bit: 2 */
#define ADC12ISSH           (0x0100)    /* ADC12 Invert Sample Hold Signal */
#define ADC12SHP            (0x0200)    /* ADC12 Sample/Hold Pulse Mode */
#define ADC12SHS0           (0x0400)    /* ADC12 Sample/Hold Source Bit: 0 */
#define ADC12SHS1           (0x0800)    /* ADC12 Sample/Hold Source Bit: 1 */
#define ADC12CSTARTADD0     (0x1000)    /* ADC12 Conversion Start Address Bit: 0 */
#define ADC12CSTARTADD1     (0x2000)    /* ADC12 Conversion Start Address Bit: 1 */
#define ADC12CSTARTADD2     (0x4000)    /* ADC12 Conversion Start Address Bit: 2 */
#define ADC12CSTARTADD3     (0x8000)    /* ADC12 Conversion Start Address Bit: 3 */

/* ADC12CTL1 Control Bits */
#define ADC12BUSY_L         (0x0001)    /* ADC12 Busy */
#define ADC12CONSEQ0_L      (0x0002)    /* ADC12 Conversion Sequence Select Bit: 0 */
#define ADC12CONSEQ1_L      (0x0004)    /* ADC12 Conversion Sequence Select Bit: 1 */
#define ADC12SSEL0_L        (0x0008)    /* ADC12 Clock Source Select Bit: 0 */
#define ADC12SSEL1_L        (0x0010)    /* ADC12 Clock Source Select Bit: 1 */
#define ADC12DIV0_L         (0x0020)    /* ADC12 Clock Divider Select Bit: 0 */
#define ADC12DIV1_L         (0x0040)    /* ADC12 Clock Divider Select Bit: 1 */
#define ADC12DIV2_L         (0x0080)    /* ADC12 Clock Divider Select Bit: 2 */

/* ADC12CTL1 Control Bits */
#define ADC12ISSH_H         (0x0001)    /* ADC12 Invert Sample Hold Signal */
#define ADC12SHP_H          (0x0002)    /* ADC12 Sample/Hold Pulse Mode */
#define ADC12SHS0_H         (0x0004)    /* ADC12 Sample/Hold Source Bit: 0 */
#define ADC12SHS1_H         (0x0008)    /* ADC12 Sample/Hold Source Bit: 1 */
#define ADC12CSTARTADD0_H   (0x0010)    /* ADC12 Conversion Start Address Bit: 0 */
#define ADC12CSTARTADD1_H   (0x0020)    /* ADC12 Conversion Start Address Bit: 1 */
#define ADC12CSTARTADD2_H   (0x0040)    /* ADC12 Conversion Start Address Bit: 2 */
#define ADC12CSTARTADD3_H   (0x0080)    /* ADC12 Conversion Start Address Bit: 3 */

#define ADC12CONSEQ_0        (0*2)      /* ADC12 Conversion Sequence Select: 0 */
#define ADC12CONSEQ_1        (1*2)      /* ADC12 Conversion Sequence Select: 1 */
#define ADC12CONSEQ_2        (2*2)      /* ADC12 Conversion Sequence Select: 2 */
#define ADC12CONSEQ_3        (3*2)      /* ADC12 Conversion Sequence Select: 3 */

#define ADC12SSEL_0          (0*8)      /* ADC12 Clock Source Select: 0 */
#define ADC12SSEL_1          (1*8)      /* ADC12 Clock Source Select: 1 */
#define ADC12SSEL_2          (2*8)      /* ADC12 Clock Source Select: 2 */
#define ADC12SSEL_3          (3*8)      /* ADC12 Clock Source Select: 3 */

#define ADC12DIV_0           (0*0x20)   /* ADC12 Clock Divider Select: 0 */
#define ADC12DIV_1           (1*0x20)   /* ADC12 Clock Divider Select: 1 */
#define ADC12DIV_2           (2*0x20)   /* ADC12 Clock Divider Select: 2 */
#define ADC12DIV_3           (3*0x20)   /* ADC12 Clock Divider Select: 3 */
#define ADC12DIV_4           (4*0x20)   /* ADC12 Clock Divider Select: 4 */
#define ADC12DIV_5           (5*0x20)   /* ADC12 Clock Divider Select: 5 */
#define ADC12DIV_6           (6*0x20)   /* ADC12 Clock Divider Select: 6 */
#define ADC12DIV_7           (7*0x20)   /* ADC12 Clock Divider Select: 7 */

#define ADC12SHS_0           (0*0x400)  /* ADC12 Sample/Hold Source: 0 */
#define ADC12SHS_1           (1*0x400)  /* ADC12 Sample/Hold Source: 1 */
#define ADC12SHS_2           (2*0x400)  /* ADC12 Sample/Hold Source: 2 */
#define ADC12SHS_3           (3*0x400)  /* ADC12 Sample/Hold Source: 3 */

#define ADC12CSTARTADD_0     (0U*0x1000) /* ADC12 Conversion Start Address: 0 */
#define ADC12CSTARTADD_1     (1U*0x1000) /* ADC12 Conversion Start Address: 1 */
#define ADC12CSTARTADD_2     (2U*0x1000) /* ADC12 Conversion Start Address: 2 */
#define ADC12CSTARTADD_3     (3U*0x1000) /* ADC12 Conversion Start Address: 3 */
#define ADC12CSTARTADD_4     (4U*0x1000) /* ADC12 Conversion Start Address: 4 */
#define ADC12CSTARTADD_5     (5U*0x1000) /* ADC12 Conversion Start Address: 5 */
#define ADC12CSTARTADD_6     (6U*0x1000) /* ADC12 Conversion Start Address: 6 */
#define ADC12CSTARTADD_7     (7U*0x1000) /* ADC12 Conversion Start Address: 7 */
#define ADC12CSTARTADD_8     (8U*0x1000) /* ADC12 Conversion Start Address: 8 */
#define ADC12CSTARTADD_9     (9U*0x1000) /* ADC12 Conversion Start Address: 9 */
#define ADC12CSTARTADD_10    (10U*0x1000) /* ADC12 Conversion Start Address: 10 */
#define ADC12CSTARTADD_11    (11U*0x1000) /* ADC12 Conversion Start Address: 11 */
#define ADC12CSTARTADD_12    (12U*0x1000) /* ADC12 Conversion Start Address: 12 */
#define ADC12CSTARTADD_13    (13U*0x1000) /* ADC12 Conversion Start Address: 13 */
#define ADC12CSTARTADD_14    (14U*0x1000) /* ADC12 Conversion Start Address: 14 */
#define ADC12CSTARTADD_15    (15U*0x1000) /* ADC12 Conversion Start Address: 15 */

/* ADC12CTL2 Control Bits */
#define ADC12REFBURST       (0x0001)    /* ADC12+ Reference Burst */
#define ADC12REFOUT         (0x0002)    /* ADC12+ Reference Out */
#define ADC12SR             (0x0004)    /* ADC12+ Sampling Rate */
#define ADC12DF             (0x0008)    /* ADC12+ Data Format */
#define ADC12RES0           (0x0010)    /* ADC12+ Resolution Bit: 0 */
#define ADC12RES1           (0x0020)    /* ADC12+ Resolution Bit: 1 */
#define ADC12TCOFF          (0x0080)    /* ADC12+ Temperature Sensor Off */
#define ADC12PDIV           (0x0100)    /* ADC12+ predivider 0:/1   1:/4 */

/* ADC12CTL2 Control Bits */
#define ADC12REFBURST_L     (0x0001)    /* ADC12+ Reference Burst */
#define ADC12REFOUT_L       (0x0002)    /* ADC12+ Reference Out */
#define ADC12SR_L           (0x0004)    /* ADC12+ Sampling Rate */
#define ADC12DF_L           (0x0008)    /* ADC12+ Data Format */
#define ADC12RES0_L         (0x0010)    /* ADC12+ Resolution Bit: 0 */
#define ADC12RES1_L         (0x0020)    /* ADC12+ Resolution Bit: 1 */
#define ADC12TCOFF_L        (0x0080)    /* ADC12+ Temperature Sensor Off */

/* ADC12CTL2 Control Bits */
#define ADC12PDIV_H         (0x0001)    /* ADC12+ predivider 0:/1   1:/4 */

#define ADC12RES_0          (0x0000)    /* ADC12+ Resolution : 8 Bit */
#define ADC12RES_1          (0x0010)    /* ADC12+ Resolution : 10 Bit */
#define ADC12RES_2          (0x0020)    /* ADC12+ Resolution : 12 Bit */
#define ADC12RES_3          (0x0030)    /* ADC12+ Resolution : reserved */

/* ADC12MCTLx Control Bits */
#define ADC12INCH0          (0x0001)    /* ADC12 Input Channel Select Bit 0 */
#define ADC12INCH1          (0x0002)    /* ADC12 Input Channel Select Bit 1 */
#define ADC12INCH2          (0x0004)    /* ADC12 Input Channel Select Bit 2 */
#define ADC12INCH3          (0x0008)    /* ADC12 Input Channel Select Bit 3 */
#define ADC12SREF0          (0x0010)    /* ADC12 Select Reference Bit 0 */
#define ADC12SREF1          (0x0020)    /* ADC12 Select Reference Bit 1 */
#define ADC12SREF2          (0x0040)    /* ADC12 Select Reference Bit 2 */
#define ADC12EOS            (0x0080)    /* ADC12 End of Sequence */

#define ADC12INCH_0         (0x0000)    /* ADC12 Input Channel 0 */
#define ADC12INCH_1         (0x0001)    /* ADC12 Input Channel 1 */
#define ADC12INCH_2         (0x0002)    /* ADC12 Input Channel 2 */
#define ADC12INCH_3         (0x0003)    /* ADC12 Input Channel 3 */
#define ADC12INCH_4         (0x0004)    /* ADC12 Input Channel 4 */
#define ADC12INCH_5         (0x0005)    /* ADC12 Input Channel 5 */
#define ADC12INCH_6         (0x0006)    /* ADC12 Input Channel 6 */
#define ADC12INCH_7         (0x0007)    /* ADC12 Input Channel 7 */
#define ADC12INCH_8         (0x0008)    /* ADC12 Input Channel 8 */
#define ADC12INCH_9         (0x0009)    /* ADC12 Input Channel 9 */
#define ADC12INCH_10        (0x000A)    /* ADC12 Input Channel 10 */
#define ADC12INCH_11        (0x000B)    /* ADC12 Input Channel 11 */
#define ADC12INCH_12        (0x000C)    /* ADC12 Input Channel 12 */
#define ADC12INCH_13        (0x000D)    /* ADC12 Input Channel 13 */
#define ADC12INCH_14        (0x000E)    /* ADC12 Input Channel 14 */
#define ADC12INCH_15        (0x000F)    /* ADC12 Input Channel 15 */

#define ADC12SREF_0         (0*0x10)    /* ADC12 Select Reference 0 */
#define ADC12SREF_1         (1*0x10)    /* ADC12 Select Reference 1 */
#define ADC12SREF_2         (2*0x10)    /* ADC12 Select Reference 2 */
#define ADC12SREF_3         (3*0x10)    /* ADC12 Select Reference 3 */
#define ADC12SREF_4         (4*0x10)    /* ADC12 Select Reference 4 */
#define ADC12SREF_5         (5*0x10)    /* ADC12 Select Reference 5 */
#define ADC12SREF_6         (6*0x10)    /* ADC12 Select Reference 6 */
#define ADC12SREF_7         (7*0x10)    /* ADC12 Select Reference 7 */

#define ADC12IE0           (0x0001)  /* ADC12 Memory 0      Interrupt Enable */
#define ADC12IE1           (0x0002)  /* ADC12 Memory 1      Interrupt Enable */
#define ADC12IE2           (0x0004)  /* ADC12 Memory 2      Interrupt Enable */
#define ADC12IE3           (0x0008)  /* ADC12 Memory 3      Interrupt Enable */
#define ADC12IE4           (0x0010)  /* ADC12 Memory 4      Interrupt Enable */
#define ADC12IE5           (0x0020)  /* ADC12 Memory 5      Interrupt Enable */
#define ADC12IE6           (0x0040)  /* ADC12 Memory 6      Interrupt Enable */
#define ADC12IE7           (0x0080)  /* ADC12 Memory 7      Interrupt Enable */
#define ADC12IE8           (0x0100)  /* ADC12 Memory 8      Interrupt Enable */
#define ADC12IE9           (0x0200)  /* ADC12 Memory 9      Interrupt Enable */
#define ADC12IE10           (0x0400)  /* ADC12 Memory 10      Interrupt Enable */
#define ADC12IE11           (0x0800)  /* ADC12 Memory 11      Interrupt Enable */
#define ADC12IE12           (0x1000)  /* ADC12 Memory 12      Interrupt Enable */
#define ADC12IE13           (0x2000)  /* ADC12 Memory 13      Interrupt Enable */
#define ADC12IE14           (0x4000)  /* ADC12 Memory 14      Interrupt Enable */
#define ADC12IE15           (0x8000)  /* ADC12 Memory 15      Interrupt Enable */

#define ADC12IE0_L          (0x0001)  /* ADC12 Memory 0      Interrupt Enable */
#define ADC12IE1_L          (0x0002)  /* ADC12 Memory 1      Interrupt Enable */
#define ADC12IE2_L          (0x0004)  /* ADC12 Memory 2      Interrupt Enable */
#define ADC12IE3_L          (0x0008)  /* ADC12 Memory 3      Interrupt Enable */
#define ADC12IE4_L          (0x0010)  /* ADC12 Memory 4      Interrupt Enable */
#define ADC12IE5_L          (0x0020)  /* ADC12 Memory 5      Interrupt Enable */
#define ADC12IE6_L          (0x0040)  /* ADC12 Memory 6      Interrupt Enable */
#define ADC12IE7_L          (0x0080)  /* ADC12 Memory 7      Interrupt Enable */

#define ADC12IE8_H          (0x0001)  /* ADC12 Memory 8      Interrupt Enable */
#define ADC12IE9_H          (0x0002)  /* ADC12 Memory 9      Interrupt Enable */
#define ADC12IE10_H         (0x0004)  /* ADC12 Memory 10      Interrupt Enable */
#define ADC12IE11_H         (0x0008)  /* ADC12 Memory 11      Interrupt Enable */
#define ADC12IE12_H         (0x0010)  /* ADC12 Memory 12      Interrupt Enable */
#define ADC12IE13_H         (0x0020)  /* ADC12 Memory 13      Interrupt Enable */
#define ADC12IE14_H         (0x0040)  /* ADC12 Memory 14      Interrupt Enable */
#define ADC12IE15_H         (0x0080)  /* ADC12 Memory 15      Interrupt Enable */

#define ADC12IFG0          (0x0001)  /* ADC12 Memory 0      Interrupt Flag */
#define ADC12IFG1          (0x0002)  /* ADC12 Memory 1      Interrupt Flag */
#define ADC12IFG2          (0x0004)  /* ADC12 Memory 2      Interrupt Flag */
#define ADC12IFG3          (0x0008)  /* ADC12 Memory 3      Interrupt Flag */
#define ADC12IFG4          (0x0010)  /* ADC12 Memory 4      Interrupt Flag */
#define ADC12IFG5          (0x0020)  /* ADC12 Memory 5      Interrupt Flag */
#define ADC12IFG6          (0x0040)  /* ADC12 Memory 6      Interrupt Flag */
#define ADC12IFG7          (0x0080)  /* ADC12 Memory 7      Interrupt Flag */
#define ADC12IFG8          (0x0100)  /* ADC12 Memory 8      Interrupt Flag */
#define ADC12IFG9          (0x0200)  /* ADC12 Memory 9      Interrupt Flag */
#define ADC12IFG10          (0x0400)  /* ADC12 Memory 10      Interrupt Flag */
#define ADC12IFG11          (0x0800)  /* ADC12 Memory 11      Interrupt Flag */
#define ADC12IFG12          (0x1000)  /* ADC12 Memory 12      Interrupt Flag */
#define ADC12IFG13          (0x2000)  /* ADC12 Memory 13      Interrupt Flag */
#define ADC12IFG14          (0x4000)  /* ADC12 Memory 14      Interrupt Flag */
#define ADC12IFG15          (0x8000)  /* ADC12 Memory 15      Interrupt Flag */

#define ADC12IFG0_L         (0x0001)  /* ADC12 Memory 0      Interrupt Flag */
#define ADC12IFG1_L         (0x0002)  /* ADC12 Memory 1      Interrupt Flag */
#define ADC12IFG2_L         (0x0004)  /* ADC12 Memory 2      Interrupt Flag */
#define ADC12IFG3_L         (0x0008)  /* ADC12 Memory 3      Interrupt Flag */
#define ADC12IFG4_L         (0x0010)  /* ADC12 Memory 4      Interrupt Flag */
#define ADC12IFG5_L         (0x0020)  /* ADC12 Memory 5      Interrupt Flag */
#define ADC12IFG6_L         (0x0040)  /* ADC12 Memory 6      Interrupt Flag */
#define ADC12IFG7_L         (0x0080)  /* ADC12 Memory 7      Interrupt Flag */

#define ADC12IFG8_H         (0x0001)  /* ADC12 Memory 8      Interrupt Flag */
#define ADC12IFG9_H         (0x0002)  /* ADC12 Memory 9      Interrupt Flag */
#define ADC12IFG10_H        (0x0004)  /* ADC12 Memory 10      Interrupt Flag */
#define ADC12IFG11_H        (0x0008)  /* ADC12 Memory 11      Interrupt Flag */
#define ADC12IFG12_H        (0x0010)  /* ADC12 Memory 12      Interrupt Flag */
#define ADC12IFG13_H        (0x0020)  /* ADC12 Memory 13      Interrupt Flag */
#define ADC12IFG14_H        (0x0040)  /* ADC12 Memory 14      Interrupt Flag */
#define ADC12IFG15_H        (0x0080)  /* ADC12 Memory 15      Interrupt Flag */

/* ADC12IV Definitions */
#define ADC12IV_NONE        (0x0000)    /* No Interrupt pending */
#define ADC12IV_ADC12OVIFG  (0x0002)    /* ADC12OVIFG */
#define ADC12IV_ADC12TOVIFG (0x0004)    /* ADC12TOVIFG */
#define ADC12IV_ADC12IFG0   (0x0006)    /* ADC12IFG0 */
#define ADC12IV_ADC12IFG1   (0x0008)    /* ADC12IFG1 */
#define ADC12IV_ADC12IFG2   (0x000A)    /* ADC12IFG2 */
#define ADC12IV_ADC12IFG3   (0x000C)    /* ADC12IFG3 */
#define ADC12IV_ADC12IFG4   (0x000E)    /* ADC12IFG4 */
#define ADC12IV_ADC12IFG5   (0x0010)    /* ADC12IFG5 */
#define ADC12IV_ADC12IFG6   (0x0012)    /* ADC12IFG6 */
#define ADC12IV_ADC12IFG7   (0x0014)    /* ADC12IFG7 */
#define ADC12IV_ADC12IFG8   (0x0016)    /* ADC12IFG8 */
#define ADC12IV_ADC12IFG9   (0x0018)    /* ADC12IFG9 */
#define ADC12IV_ADC12IFG10  (0x001A)    /* ADC12IFG10 */
#define ADC12IV_ADC12IFG11  (0x001C)    /* ADC12IFG11 */
#define ADC12IV_ADC12IFG12  (0x001E)    /* ADC12IFG12 */
#define ADC12IV_ADC12IFG13  (0x0020)    /* ADC12IFG13 */
#define ADC12IV_ADC12IFG14  (0x0022)    /* ADC12IFG14 */
#define ADC12IV_ADC12IFG15  (0x0024)    /* ADC12IFG15 */

/************************************************************
* Comparator B
************************************************************/
#define __MSP430_HAS_COMPB__          /* Definition to show that Module is available */

#define CBCTL0_               0x08C0    /* Comparator B Control Register 0 */
sfrb(CBCTL0_L, CBCTL0_);
sfrb(CBCTL0_H, CBCTL0_+1);
sfrw(CBCTL0, CBCTL0_);
#define CBCTL1_               0x08C2    /* Comparator B Control Register 1 */
sfrb(CBCTL1_L, CBCTL1_);
sfrb(CBCTL1_H, CBCTL1_+1);
sfrw(CBCTL1, CBCTL1_);
#define CBCTL2_               0x08C4    /* Comparator B Control Register 2 */
sfrb(CBCTL2_L, CBCTL2_);
sfrb(CBCTL2_H, CBCTL2_+1);
sfrw(CBCTL2, CBCTL2_);
#define CBCTL3_               0x08C6    /* Comparator B Control Register 3 */
sfrb(CBCTL3_L, CBCTL3_);
sfrb(CBCTL3_H, CBCTL3_+1);
sfrw(CBCTL3, CBCTL3_);
#define CBINT_                0x08CC    /* Comparator B Interrupt Register */
sfrb(CBINT_L, CBINT_);
sfrb(CBINT_H, CBINT_+1);
sfrw(CBINT, CBINT_);
#define CBIV_                 0x08CE    /* Comparator B Interrupt Vector Word */
sfrw(CBIV, CBIV_);


/* CBCTL0 Control Bits */
#define CBIPSEL0            (0x0001)  /* Comp. B Pos. Channel Input Select 0 */
#define CBIPSEL1            (0x0002)  /* Comp. B Pos. Channel Input Select 1 */
#define CBIPSEL2            (0x0004)  /* Comp. B Pos. Channel Input Select 2 */
#define CBIPSEL3            (0x0008)  /* Comp. B Pos. Channel Input Select 3 */
//#define RESERVED            (0x0010)  /* Comp. B */
//#define RESERVED            (0x0020)  /* Comp. B */
//#define RESERVED            (0x0040)  /* Comp. B */
#define CBIPEN              (0x0080)  /* Comp. B Pos. Channel Input Enable */
#define CBIMSEL0            (0x0100)  /* Comp. B Neg. Channel Input Select 0 */
#define CBIMSEL1            (0x0200)  /* Comp. B Neg. Channel Input Select 1 */
#define CBIMSEL2            (0x0400)  /* Comp. B Neg. Channel Input Select 2 */
#define CBIMSEL3            (0x0800)  /* Comp. B Neg. Channel Input Select 3 */
//#define RESERVED            (0x1000)  /* Comp. B */
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */
#define CBIMEN              (0x8000)  /* Comp. B Neg. Channel Input Enable */

/* CBCTL0 Control Bits */
#define CBIPSEL0_L          (0x0001)  /* Comp. B Pos. Channel Input Select 0 */
#define CBIPSEL1_L          (0x0002)  /* Comp. B Pos. Channel Input Select 1 */
#define CBIPSEL2_L          (0x0004)  /* Comp. B Pos. Channel Input Select 2 */
#define CBIPSEL3_L          (0x0008)  /* Comp. B Pos. Channel Input Select 3 */
//#define RESERVED            (0x0010)  /* Comp. B */
//#define RESERVED            (0x0020)  /* Comp. B */
//#define RESERVED            (0x0040)  /* Comp. B */
#define CBIPEN_L            (0x0080)  /* Comp. B Pos. Channel Input Enable */
//#define RESERVED            (0x1000)  /* Comp. B */
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */

/* CBCTL0 Control Bits */
//#define RESERVED            (0x0010)  /* Comp. B */
//#define RESERVED            (0x0020)  /* Comp. B */
//#define RESERVED            (0x0040)  /* Comp. B */
#define CBIMSEL0_H          (0x0001)  /* Comp. B Neg. Channel Input Select 0 */
#define CBIMSEL1_H          (0x0002)  /* Comp. B Neg. Channel Input Select 1 */
#define CBIMSEL2_H          (0x0004)  /* Comp. B Neg. Channel Input Select 2 */
#define CBIMSEL3_H          (0x0008)  /* Comp. B Neg. Channel Input Select 3 */
//#define RESERVED            (0x1000)  /* Comp. B */
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */
#define CBIMEN_H            (0x0080)  /* Comp. B Neg. Channel Input Enable */

#define CBIPSEL_0           (0x0000)  /* Comp. B V+ terminal Input Select: Channel 0 */
#define CBIPSEL_1           (0x0001)  /* Comp. B V+ terminal Input Select: Channel 1 */
#define CBIPSEL_2           (0x0002)  /* Comp. B V+ terminal Input Select: Channel 2 */
#define CBIPSEL_3           (0x0003)  /* Comp. B V+ terminal Input Select: Channel 3 */
#define CBIPSEL_4           (0x0004)  /* Comp. B V+ terminal Input Select: Channel 4 */
#define CBIPSEL_5           (0x0005)  /* Comp. B V+ terminal Input Select: Channel 5 */
#define CBIPSEL_6           (0x0006)  /* Comp. B V+ terminal Input Select: Channel 6 */
#define CBIPSEL_7           (0x0007)  /* Comp. B V+ terminal Input Select: Channel 7 */
#define CBIPSEL_8           (0x0008)  /* Comp. B V+ terminal Input Select: Channel 8 */
#define CBIPSEL_9           (0x0009)  /* Comp. B V+ terminal Input Select: Channel 9 */
#define CBIPSEL_10          (0x000A)  /* Comp. B V+ terminal Input Select: Channel 10 */
#define CBIPSEL_11          (0x000B)  /* Comp. B V+ terminal Input Select: Channel 11 */
#define CBIPSEL_12          (0x000C)  /* Comp. B V+ terminal Input Select: Channel 12 */
#define CBIPSEL_13          (0x000D)  /* Comp. B V+ terminal Input Select: Channel 13 */
#define CBIPSEL_14          (0x000E)  /* Comp. B V+ terminal Input Select: Channel 14 */
#define CBIPSEL_15          (0x000F)  /* Comp. B V+ terminal Input Select: Channel 15 */
                                                                          
#define CBIMSEL_0           (0x0000)  /* Comp. B V- Terminal Input Select: Channel 0 */
#define CBIMSEL_1           (0x0100)  /* Comp. B V- Terminal Input Select: Channel 1 */
#define CBIMSEL_2           (0x0200)  /* Comp. B V- Terminal Input Select: Channel 2 */
#define CBIMSEL_3           (0x0300)  /* Comp. B V- Terminal Input Select: Channel 3 */
#define CBIMSEL_4           (0x0400)  /* Comp. B V- Terminal Input Select: Channel 4 */
#define CBIMSEL_5           (0x0500)  /* Comp. B V- Terminal Input Select: Channel 5 */
#define CBIMSEL_6           (0x0600)  /* Comp. B V- Terminal Input Select: Channel 6 */
#define CBIMSEL_7           (0x0700)  /* Comp. B V- Terminal Input Select: Channel 7 */
#define CBIMSEL_8           (0x0800)  /* Comp. B V- terminal Input Select: Channel 8 */
#define CBIMSEL_9           (0x0900)  /* Comp. B V- terminal Input Select: Channel 9 */
#define CBIMSEL_10          (0x0A00)  /* Comp. B V- terminal Input Select: Channel 10 */
#define CBIMSEL_11          (0x0B00)  /* Comp. B V- terminal Input Select: Channel 11 */
#define CBIMSEL_12          (0x0C00)  /* Comp. B V- terminal Input Select: Channel 12 */
#define CBIMSEL_13          (0x0D00)  /* Comp. B V- terminal Input Select: Channel 13 */
#define CBIMSEL_14          (0x0E00)  /* Comp. B V- terminal Input Select: Channel 14 */
#define CBIMSEL_15          (0x0F00)  /* Comp. B V- terminal Input Select: Channel 15 */
                                           
/* CBCTL1 Control Bits */
#define CBOUT               (0x0001)  /* Comp. B Output */
#define CBOUTPOL            (0x0002)  /* Comp. B Output Polarity */
#define CBF                 (0x0004)  /* Comp. B Enable Output Filter */
#define CBIES               (0x0008)  /* Comp. B Interrupt Edge Select */
#define CBSHORT             (0x0010)  /* Comp. B Input Short */
#define CBEX                (0x0020)  /* Comp. B Exchange Inputs */
#define CBFDLY0             (0x0040)  /* Comp. B Filter delay Bit 0 */
#define CBFDLY1             (0x0080)  /* Comp. B Filter delay Bit 1 */
#define CBPWRMD0            (0x0100)  /* Comp. B Power Mode Bit 0 */
#define CBPWRMD1            (0x0200)  /* Comp. B Power Mode Bit 1 */
#define CBON                (0x0400)  /* Comp. B enable */
#define CBMRVL              (0x0800)  /* Comp. B CBMRV Level */
#define CBMRVS              (0x1000)  /* Comp. B Output selects between VREF0 or VREF1*/
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */
//#define RESERVED            (0x8000)  /* Comp. B */

/* CBCTL1 Control Bits */
#define CBOUT_L             (0x0001)  /* Comp. B Output */
#define CBOUTPOL_L          (0x0002)  /* Comp. B Output Polarity */
#define CBF_L               (0x0004)  /* Comp. B Enable Output Filter */
#define CBIES_L             (0x0008)  /* Comp. B Interrupt Edge Select */
#define CBSHORT_L           (0x0010)  /* Comp. B Input Short */
#define CBEX_L              (0x0020)  /* Comp. B Exchange Inputs */
#define CBFDLY0_L           (0x0040)  /* Comp. B Filter delay Bit 0 */
#define CBFDLY1_L           (0x0080)  /* Comp. B Filter delay Bit 1 */
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */
//#define RESERVED            (0x8000)  /* Comp. B */

/* CBCTL1 Control Bits */
#define CBPWRMD0_H          (0x0001)  /* Comp. B Power Mode Bit 0 */
#define CBPWRMD1_H          (0x0002)  /* Comp. B Power Mode Bit 1 */
#define CBON_H              (0x0004)  /* Comp. B enable */
#define CBMRVL_H            (0x0008)  /* Comp. B CBMRV Level */
#define CBMRVS_H            (0x0010)  /* Comp. B Output selects between VREF0 or VREF1*/
//#define RESERVED            (0x2000)  /* Comp. B */
//#define RESERVED            (0x4000)  /* Comp. B */
//#define RESERVED            (0x8000)  /* Comp. B */

#define CBFDLY_0           (0x0000)  /* Comp. B Filter delay 0 : 450ns */
#define CBFDLY_1           (0x0040)  /* Comp. B Filter delay 1 : 900ns */
#define CBFDLY_2           (0x0080)  /* Comp. B Filter delay 2 : 1800ns */
#define CBFDLY_3           (0x00C0)  /* Comp. B Filter delay 3 : 3600ns */

#define CBPWRMD_0           (0x0000)  /* Comp. B Power Mode 0 : High speed */
#define CBPWRMD_1           (0x0100)  /* Comp. B Power Mode 1 : Normal */
#define CBPWRMD_2           (0x0200)  /* Comp. B Power Mode 2 : Ultra-Low*/
#define CBPWRMD_3           (0x0300)  /* Comp. B Power Mode 3 : Reserved */


/* CBCTL2 Control Bits */
#define CBREF00             (0x0001)  /* Comp. B Reference 0 Resistor Select Bit : 0 */
#define CBREF01             (0x0002)  /* Comp. B Reference 0 Resistor Select Bit : 1 */
#define CBREF02             (0x0004)  /* Comp. B Reference 0 Resistor Select Bit : 2 */
#define CBREF03             (0x0008)  /* Comp. B Reference 0 Resistor Select Bit : 3 */
#define CBREF04             (0x0010)  /* Comp. B Reference 0 Resistor Select Bit : 4 */
#define CBRSEL              (0x0020)  /* Comp. B Reference select */
#define CBRS0               (0x0040)  /* Comp. B Reference Source Bit : 0 */
#define CBRS1               (0x0080)  /* Comp. B Reference Source Bit : 1 */
#define CBREF10             (0x0100)  /* Comp. B Reference 1 Resistor Select Bit : 0 */
#define CBREF11             (0x0200)  /* Comp. B Reference 1 Resistor Select Bit : 1 */
#define CBREF12             (0x0400)  /* Comp. B Reference 1 Resistor Select Bit : 2 */
#define CBREF13             (0x0800)  /* Comp. B Reference 1 Resistor Select Bit : 3 */
#define CBREF14             (0x1000)  /* Comp. B Reference 1 Resistor Select Bit : 4 */
#define CBREFL0             (0x2000)  /* Comp. B Reference voltage level Bit : 0 */
#define CBREFL1             (0x4000)  /* Comp. B Reference voltage level Bit : 1 */
#define CBREFACC            (0x8000)  /* Comp. B Reference Accuracy */

/* CBCTL2 Control Bits */
#define CBREF00_L           (0x0001)  /* Comp. B Reference 0 Resistor Select Bit : 0 */
#define CBREF01_L           (0x0002)  /* Comp. B Reference 0 Resistor Select Bit : 1 */
#define CBREF02_L           (0x0004)  /* Comp. B Reference 0 Resistor Select Bit : 2 */
#define CBREF03_L           (0x0008)  /* Comp. B Reference 0 Resistor Select Bit : 3 */
#define CBREF04_L           (0x0010)  /* Comp. B Reference 0 Resistor Select Bit : 4 */
#define CBRSEL_L            (0x0020)  /* Comp. B Reference select */
#define CBRS0_L             (0x0040)  /* Comp. B Reference Source Bit : 0 */
#define CBRS1_L             (0x0080)  /* Comp. B Reference Source Bit : 1 */

/* CBCTL2 Control Bits */
#define CBREF10_H           (0x0001)  /* Comp. B Reference 1 Resistor Select Bit : 0 */
#define CBREF11_H           (0x0002)  /* Comp. B Reference 1 Resistor Select Bit : 1 */
#define CBREF12_H           (0x0004)  /* Comp. B Reference 1 Resistor Select Bit : 2 */
#define CBREF13_H           (0x0008)  /* Comp. B Reference 1 Resistor Select Bit : 3 */
#define CBREF14_H           (0x0010)  /* Comp. B Reference 1 Resistor Select Bit : 4 */
#define CBREFL0_H           (0x0020)  /* Comp. B Reference voltage level Bit : 0 */
#define CBREFL1_H           (0x0040)  /* Comp. B Reference voltage level Bit : 1 */
#define CBREFACC_H          (0x0080)  /* Comp. B Reference Accuracy */

#define CBREF0_0            (0x0000)  /* Comp. B Int. Ref.0 Select 0 : 1/32 */
#define CBREF0_1            (0x0001)  /* Comp. B Int. Ref.0 Select 1 : 2/32 */
#define CBREF0_2            (0x0002)  /* Comp. B Int. Ref.0 Select 2 : 3/32 */
#define CBREF0_3            (0x0003)  /* Comp. B Int. Ref.0 Select 3 : 4/32 */
#define CBREF0_4            (0x0004)  /* Comp. B Int. Ref.0 Select 4 : 5/32 */
#define CBREF0_5            (0x0005)  /* Comp. B Int. Ref.0 Select 5 : 6/32 */
#define CBREF0_6            (0x0006)  /* Comp. B Int. Ref.0 Select 6 : 7/32 */
#define CBREF0_7            (0x0007)  /* Comp. B Int. Ref.0 Select 7 : 8/32 */
#define CBREF0_8            (0x0008)  /* Comp. B Int. Ref.0 Select 0 : 9/32 */
#define CBREF0_9            (0x0009)  /* Comp. B Int. Ref.0 Select 1 : 10/32 */
#define CBREF0_10           (0x000A)  /* Comp. B Int. Ref.0 Select 2 : 11/32 */
#define CBREF0_11           (0x000B)  /* Comp. B Int. Ref.0 Select 3 : 12/32 */
#define CBREF0_12           (0x000C)  /* Comp. B Int. Ref.0 Select 4 : 13/32 */
#define CBREF0_13           (0x000D)  /* Comp. B Int. Ref.0 Select 5 : 14/32 */
#define CBREF0_14           (0x000E)  /* Comp. B Int. Ref.0 Select 6 : 15/32 */
#define CBREF0_15           (0x000F)  /* Comp. B Int. Ref.0 Select 7 : 16/32 */
#define CBREF0_16           (0x0010)  /* Comp. B Int. Ref.0 Select 0 : 17/32 */
#define CBREF0_17           (0x0011)  /* Comp. B Int. Ref.0 Select 1 : 18/32 */
#define CBREF0_18           (0x0012)  /* Comp. B Int. Ref.0 Select 2 : 19/32 */
#define CBREF0_19           (0x0013)  /* Comp. B Int. Ref.0 Select 3 : 20/32 */
#define CBREF0_20           (0x0014)  /* Comp. B Int. Ref.0 Select 4 : 21/32 */
#define CBREF0_21           (0x0015)  /* Comp. B Int. Ref.0 Select 5 : 22/32 */
#define CBREF0_22           (0x0016)  /* Comp. B Int. Ref.0 Select 6 : 23/32 */
#define CBREF0_23           (0x0017)  /* Comp. B Int. Ref.0 Select 7 : 24/32 */
#define CBREF0_24           (0x0018)  /* Comp. B Int. Ref.0 Select 0 : 25/32 */
#define CBREF0_25           (0x0019)  /* Comp. B Int. Ref.0 Select 1 : 26/32 */
#define CBREF0_26           (0x001A)  /* Comp. B Int. Ref.0 Select 2 : 27/32 */
#define CBREF0_27           (0x001B)  /* Comp. B Int. Ref.0 Select 3 : 28/32 */
#define CBREF0_28           (0x001C)  /* Comp. B Int. Ref.0 Select 4 : 29/32 */
#define CBREF0_29           (0x001D)  /* Comp. B Int. Ref.0 Select 5 : 30/32 */
#define CBREF0_30           (0x001E)  /* Comp. B Int. Ref.0 Select 6 : 31/32 */
#define CBREF0_31           (0x001F)  /* Comp. B Int. Ref.0 Select 7 : 32/32 */

#define CBRS_0              (0x0000)  /* Comp. B Reference Source 0 : Off */
#define CBRS_1              (0x0040)  /* Comp. B Reference Source 1 : Vcc */
#define CBRS_2              (0x0080)  /* Comp. B Reference Source 2 : Shared Ref. */
#define CBRS_3              (0x00C0)  /* Comp. B Reference Source 3 : Shared Ref. / Off */

#define CBREF1_0            (0x0000)  /* Comp. B Int. Ref.1 Select 0 : 1/32 */
#define CBREF1_1            (0x0100)  /* Comp. B Int. Ref.1 Select 1 : 2/32 */
#define CBREF1_2            (0x0200)  /* Comp. B Int. Ref.1 Select 2 : 3/32 */
#define CBREF1_3            (0x0300)  /* Comp. B Int. Ref.1 Select 3 : 4/32 */
#define CBREF1_4            (0x0400)  /* Comp. B Int. Ref.1 Select 4 : 5/32 */
#define CBREF1_5            (0x0500)  /* Comp. B Int. Ref.1 Select 5 : 6/32 */
#define CBREF1_6            (0x0600)  /* Comp. B Int. Ref.1 Select 6 : 7/32 */
#define CBREF1_7            (0x0700)  /* Comp. B Int. Ref.1 Select 7 : 8/32 */
#define CBREF1_8            (0x0800)  /* Comp. B Int. Ref.1 Select 0 : 9/32 */
#define CBREF1_9            (0x0900)  /* Comp. B Int. Ref.1 Select 1 : 10/32 */
#define CBREF1_10           (0x0A00)  /* Comp. B Int. Ref.1 Select 2 : 11/32 */
#define CBREF1_11           (0x0B00)  /* Comp. B Int. Ref.1 Select 3 : 12/32 */
#define CBREF1_12           (0x0C00)  /* Comp. B Int. Ref.1 Select 4 : 13/32 */
#define CBREF1_13           (0x0D00)  /* Comp. B Int. Ref.1 Select 5 : 14/32 */
#define CBREF1_14           (0x0E00)  /* Comp. B Int. Ref.1 Select 6 : 15/32 */
#define CBREF1_15           (0x0F00)  /* Comp. B Int. Ref.1 Select 7 : 16/32 */
#define CBREF1_16           (0x1000)  /* Comp. B Int. Ref.1 Select 0 : 17/32 */
#define CBREF1_17           (0x1100)  /* Comp. B Int. Ref.1 Select 1 : 18/32 */
#define CBREF1_18           (0x1200)  /* Comp. B Int. Ref.1 Select 2 : 19/32 */
#define CBREF1_19           (0x1300)  /* Comp. B Int. Ref.1 Select 3 : 20/32 */
#define CBREF1_20           (0x1400)  /* Comp. B Int. Ref.1 Select 4 : 21/32 */
#define CBREF1_21           (0x1500)  /* Comp. B Int. Ref.1 Select 5 : 22/32 */
#define CBREF1_22           (0x1600)  /* Comp. B Int. Ref.1 Select 6 : 23/32 */
#define CBREF1_23           (0x1700)  /* Comp. B Int. Ref.1 Select 7 : 24/32 */
#define CBREF1_24           (0x1800)  /* Comp. B Int. Ref.1 Select 0 : 25/32 */
#define CBREF1_25           (0x1900)  /* Comp. B Int. Ref.1 Select 1 : 26/32 */
#define CBREF1_26           (0x1A00)  /* Comp. B Int. Ref.1 Select 2 : 27/32 */
#define CBREF1_27           (0x1B00)  /* Comp. B Int. Ref.1 Select 3 : 28/32 */
#define CBREF1_28           (0x1C00)  /* Comp. B Int. Ref.1 Select 4 : 29/32 */
#define CBREF1_29           (0x1D00)  /* Comp. B Int. Ref.1 Select 5 : 30/32 */
#define CBREF1_30           (0x1E00)  /* Comp. B Int. Ref.1 Select 6 : 31/32 */
#define CBREF1_31           (0x1F00)  /* Comp. B Int. Ref.1 Select 7 : 32/32 */

#define CBREFL_0            (0x0000)  /* Comp. B Reference voltage level 0 : None */
#define CBREFL_1            (0x2000)  /* Comp. B Reference voltage level 1 : 1.5V */
#define CBREFL_2            (0x4000)  /* Comp. B Reference voltage level 2 : 2.0V  */
#define CBREFL_3            (0x6000)  /* Comp. B Reference voltage level 3 : 2.5V  */


#define CBPD0               (0x0001)  /* Comp. B Disable Input Buffer of Port Register .0 */
#define CBPD1               (0x0002)  /* Comp. B Disable Input Buffer of Port Register .1 */
#define CBPD2               (0x0004)  /* Comp. B Disable Input Buffer of Port Register .2 */
#define CBPD3               (0x0008)  /* Comp. B Disable Input Buffer of Port Register .3 */
#define CBPD4               (0x0010)  /* Comp. B Disable Input Buffer of Port Register .4 */
#define CBPD5               (0x0020)  /* Comp. B Disable Input Buffer of Port Register .5 */
#define CBPD6               (0x0040)  /* Comp. B Disable Input Buffer of Port Register .6 */
#define CBPD7               (0x0080)  /* Comp. B Disable Input Buffer of Port Register .7 */
#define CBPD8               (0x0100)  /* Comp. B Disable Input Buffer of Port Register .8 */
#define CBPD9               (0x0200)  /* Comp. B Disable Input Buffer of Port Register .9 */
#define CBPD10              (0x0400)  /* Comp. B Disable Input Buffer of Port Register .10 */
#define CBPD11              (0x0800)  /* Comp. B Disable Input Buffer of Port Register .11 */
#define CBPD12              (0x1000)  /* Comp. B Disable Input Buffer of Port Register .12 */
#define CBPD13              (0x2000)  /* Comp. B Disable Input Buffer of Port Register .13 */
#define CBPD14              (0x4000)  /* Comp. B Disable Input Buffer of Port Register .14 */
#define CBPD15              (0x8000)  /* Comp. B Disable Input Buffer of Port Register .15 */

#define CBPD0_L             (0x0001)  /* Comp. B Disable Input Buffer of Port Register .0 */
#define CBPD1_L             (0x0002)  /* Comp. B Disable Input Buffer of Port Register .1 */
#define CBPD2_L             (0x0004)  /* Comp. B Disable Input Buffer of Port Register .2 */
#define CBPD3_L             (0x0008)  /* Comp. B Disable Input Buffer of Port Register .3 */
#define CBPD4_L             (0x0010)  /* Comp. B Disable Input Buffer of Port Register .4 */
#define CBPD5_L             (0x0020)  /* Comp. B Disable Input Buffer of Port Register .5 */
#define CBPD6_L             (0x0040)  /* Comp. B Disable Input Buffer of Port Register .6 */
#define CBPD7_L             (0x0080)  /* Comp. B Disable Input Buffer of Port Register .7 */

#define CBPD8_H             (0x0001)  /* Comp. B Disable Input Buffer of Port Register .8 */
#define CBPD9_H             (0x0002)  /* Comp. B Disable Input Buffer of Port Register .9 */
#define CBPD10_H            (0x0004)  /* Comp. B Disable Input Buffer of Port Register .10 */
#define CBPD11_H            (0x0008)  /* Comp. B Disable Input Buffer of Port Register .11 */
#define CBPD12_H            (0x0010)  /* Comp. B Disable Input Buffer of Port Register .12 */
#define CBPD13_H            (0x0020)  /* Comp. B Disable Input Buffer of Port Register .13 */
#define CBPD14_H            (0x0040)  /* Comp. B Disable Input Buffer of Port Register .14 */
#define CBPD15_H            (0x0080)  /* Comp. B Disable Input Buffer of Port Register .15 */


/* CBINT Control Bits */
#define CBIFG                (0x0001)  /* Comp. B Interrupt Flag */
#define CBIIFG               (0x0002)  /* Comp. B Interrupt Flag Inverted Polarity */
//#define RESERVED             (0x0004)  /* Comp. B */
//#define RESERVED             (0x0008)  /* Comp. B */
//#define RESERVED             (0x0010)  /* Comp. B */
//#define RESERVED             (0x0020)  /* Comp. B */
//#define RESERVED             (0x0040)  /* Comp. B */
//#define RESERVED             (0x0080)  /* Comp. B */
#define CBIE                 (0x0100)  /* Comp. B Interrupt Enable */
#define CBIIE                (0x0200)  /* Comp. B Interrupt Enable Inverted Polarity */
//#define RESERVED             (0x0400)  /* Comp. B */
//#define RESERVED             (0x0800)  /* Comp. B */
//#define RESERVED             (0x1000)  /* Comp. B */
//#define RESERVED             (0x2000)  /* Comp. B */
//#define RESERVED             (0x4000)  /* Comp. B */
//#define RESERVED             (0x8000)  /* Comp. B */

/* CBINT Control Bits */
#define CBIFG_L             (0x0001)  /* Comp. B Interrupt Flag */
#define CBIIFG_L            (0x0002)  /* Comp. B Interrupt Flag Inverted Polarity */
//#define RESERVED             (0x0004)  /* Comp. B */
//#define RESERVED             (0x0008)  /* Comp. B */
//#define RESERVED             (0x0010)  /* Comp. B */
//#define RESERVED             (0x0020)  /* Comp. B */
//#define RESERVED             (0x0040)  /* Comp. B */
//#define RESERVED             (0x0080)  /* Comp. B */
//#define RESERVED             (0x0400)  /* Comp. B */
//#define RESERVED             (0x0800)  /* Comp. B */
//#define RESERVED             (0x1000)  /* Comp. B */
//#define RESERVED             (0x2000)  /* Comp. B */
//#define RESERVED             (0x4000)  /* Comp. B */
//#define RESERVED             (0x8000)  /* Comp. B */

/* CBINT Control Bits */
//#define RESERVED             (0x0004)  /* Comp. B */
//#define RESERVED             (0x0008)  /* Comp. B */
//#define RESERVED             (0x0010)  /* Comp. B */
//#define RESERVED             (0x0020)  /* Comp. B */
//#define RESERVED             (0x0040)  /* Comp. B */
//#define RESERVED             (0x0080)  /* Comp. B */
#define CBIE_H              (0x0001)  /* Comp. B Interrupt Enable */
#define CBIIE_H             (0x0002)  /* Comp. B Interrupt Enable Inverted Polarity */
//#define RESERVED             (0x0400)  /* Comp. B */
//#define RESERVED             (0x0800)  /* Comp. B */
//#define RESERVED             (0x1000)  /* Comp. B */
//#define RESERVED             (0x2000)  /* Comp. B */
//#define RESERVED             (0x4000)  /* Comp. B */
//#define RESERVED             (0x8000)  /* Comp. B */

/* CBIV Definitions */
#define CBIV_NONE           (0x0000)    /* No Interrupt pending */
#define CBIV_CBIFG          (0x0002)    /* CBIFG */
#define CBIV_CBIIFG         (0x0004)    /* CBIIFG */

/*************************************************************
* CRC Module
*************************************************************/
#define __MSP430_HAS_CRC__            /* Definition to show that Module is available */

#define CRCDI_                0x0150    /* CRC Data In Register */
sfrb(CRCDI_L, CRCDI_);
sfrb(CRCDI_H, CRCDI_+1);
sfrw(CRCDI, CRCDI_);
#define CRCDIRB_              0x0152    /* CRC data in reverse byte Register */
sfrb(CRCDIRB_L, CRCDIRB_);
sfrb(CRCDIRB_H, CRCDIRB_+1);
sfrw(CRCDIRB, CRCDIRB_);
#define CRCINIRES_            0x0154    /* CRC Initialisation Register and Result Register */
sfrb(CRCINIRES_L, CRCINIRES_);
sfrb(CRCINIRES_H, CRCINIRES_+1);
sfrw(CRCINIRES, CRCINIRES_);
#define CRCRESR_              0x0156    /* CRC reverse result Register */
sfrb(CRCRESR_L, CRCRESR_);
sfrb(CRCRESR_H, CRCRESR_+1);
sfrw(CRCRESR, CRCRESR_);

/************************************************************
* DMA_X
************************************************************/
#define __MSP430_HAS_DMAX_3__           /* Definition to show that Module is available */

#define DMACTL0_              0x0500    /* DMA Module Control 0 */
sfrb(DMACTL0_L, DMACTL0_);
sfrb(DMACTL0_H, DMACTL0_+1);
sfrw(DMACTL0, DMACTL0_);
#define DMACTL1_              0x0502    /* DMA Module Control 1 */
sfrb(DMACTL1_L, DMACTL1_);
sfrb(DMACTL1_H, DMACTL1_+1);
sfrw(DMACTL1, DMACTL1_);
#define DMACTL2_              0x0504    /* DMA Module Control 2 */
sfrb(DMACTL2_L, DMACTL2_);
sfrb(DMACTL2_H, DMACTL2_+1);
sfrw(DMACTL2, DMACTL2_);
#define DMACTL3_              0x0506    /* DMA Module Control 3 */
sfrb(DMACTL3_L, DMACTL3_);
sfrb(DMACTL3_H, DMACTL3_+1);
sfrw(DMACTL3, DMACTL3_);
#define DMACTL4_              0x0508    /* DMA Module Control 4 */
sfrb(DMACTL4_L, DMACTL4_);
sfrb(DMACTL4_H, DMACTL4_+1);
sfrw(DMACTL4, DMACTL4_);
#define DMAIV_                0x050E    /* DMA Interrupt Vector Word */
sfrb(DMAIV_L, DMAIV_);
sfrb(DMAIV_H, DMAIV_+1);
sfrw(DMAIV, DMAIV_);

#define DMA0CTL_              0x0510    /* DMA Channel 0 Control */
sfrb(DMA0CTL_L, DMA0CTL_);
sfrb(DMA0CTL_H, DMA0CTL_+1);
sfrw(DMA0CTL, DMA0CTL_);
#define DMA0SA_               0x0512    /* DMA Channel 0 Source Address */
sfra(DMA0SA, DMA0SA_);
#define DMA0DA_               0x0516    /* DMA Channel 0 Destination Address */
sfra(DMA0DA, DMA0DA_);
#define DMA0SZ_               0x051A    /* DMA Channel 0 Transfer Size */
sfrw(DMA0SZ, DMA0SZ_);

#define DMA1CTL_              0x0520    /* DMA Channel 1 Control */
sfrb(DMA1CTL_L, DMA1CTL_);
sfrb(DMA1CTL_H, DMA1CTL_+1);
sfrw(DMA1CTL, DMA1CTL_);
#define DMA1SA_               0x0522    /* DMA Channel 1 Source Address */
sfra(DMA1SA, DMA1SA_);
#define DMA1DA_               0x0526    /* DMA Channel 1 Destination Address */
sfra(DMA1DA, DMA1DA_);
#define DMA1SZ_               0x052A    /* DMA Channel 1 Transfer Size */
sfrw(DMA1SZ, DMA1SZ_);

#define DMA2CTL_              0x0530    /* DMA Channel 2 Control */
sfrb(DMA2CTL_L, DMA2CTL_);
sfrb(DMA2CTL_H, DMA2CTL_+1);
sfrw(DMA2CTL, DMA2CTL_);
#define DMA2SA_               0x0532    /* DMA Channel 2 Source Address */
sfra(DMA2SA, DMA2SA_);
#define DMA2DA_               0x0536    /* DMA Channel 2 Destination Address */
sfra(DMA2DA, DMA2DA_);
#define DMA2SZ_               0x053A    /* DMA Channel 2 Transfer Size */
sfrw(DMA2SZ, DMA2SZ_);

/* DMACTL0 Control Bits */
#define DMA0TSEL0           (0x0001)    /* DMA channel 0 transfer select bit 0 */
#define DMA0TSEL1           (0x0002)    /* DMA channel 0 transfer select bit 1 */
#define DMA0TSEL2           (0x0004)    /* DMA channel 0 transfer select bit 2 */
#define DMA0TSEL3           (0x0008)    /* DMA channel 0 transfer select bit 3 */
#define DMA0TSEL4           (0x0010)    /* DMA channel 0 transfer select bit 4 */
#define DMA1TSEL0           (0x0100)    /* DMA channel 1 transfer select bit 0 */
#define DMA1TSEL1           (0x0200)    /* DMA channel 1 transfer select bit 1 */
#define DMA1TSEL2           (0x0400)    /* DMA channel 1 transfer select bit 2 */
#define DMA1TSEL3           (0x0800)    /* DMA channel 1 transfer select bit 3 */
#define DMA1TSEL4           (0x1000)    /* DMA channel 1 transfer select bit 4 */

/* DMACTL0 Control Bits */
#define DMA0TSEL0_L         (0x0001)    /* DMA channel 0 transfer select bit 0 */
#define DMA0TSEL1_L         (0x0002)    /* DMA channel 0 transfer select bit 1 */
#define DMA0TSEL2_L         (0x0004)    /* DMA channel 0 transfer select bit 2 */
#define DMA0TSEL3_L         (0x0008)    /* DMA channel 0 transfer select bit 3 */
#define DMA0TSEL4_L         (0x0010)    /* DMA channel 0 transfer select bit 4 */

/* DMACTL0 Control Bits */
#define DMA1TSEL0_H         (0x0001)    /* DMA channel 1 transfer select bit 0 */
#define DMA1TSEL1_H         (0x0002)    /* DMA channel 1 transfer select bit 1 */
#define DMA1TSEL2_H         (0x0004)    /* DMA channel 1 transfer select bit 2 */
#define DMA1TSEL3_H         (0x0008)    /* DMA channel 1 transfer select bit 3 */
#define DMA1TSEL4_H         (0x0010)    /* DMA channel 1 transfer select bit 4 */

/* DMACTL01 Control Bits */
#define DMA2TSEL0           (0x0001)    /* DMA channel 2 transfer select bit 0 */
#define DMA2TSEL1           (0x0002)    /* DMA channel 2 transfer select bit 1 */
#define DMA2TSEL2           (0x0004)    /* DMA channel 2 transfer select bit 2 */
#define DMA2TSEL3           (0x0008)    /* DMA channel 2 transfer select bit 3 */
#define DMA2TSEL4           (0x0010)    /* DMA channel 2 transfer select bit 4 */

/* DMACTL01 Control Bits */
#define DMA2TSEL0_L         (0x0001)    /* DMA channel 2 transfer select bit 0 */
#define DMA2TSEL1_L         (0x0002)    /* DMA channel 2 transfer select bit 1 */
#define DMA2TSEL2_L         (0x0004)    /* DMA channel 2 transfer select bit 2 */
#define DMA2TSEL3_L         (0x0008)    /* DMA channel 2 transfer select bit 3 */
#define DMA2TSEL4_L         (0x0010)    /* DMA channel 2 transfer select bit 4 */

/* DMACTL01 Control Bits */

/* DMACTL4 Control Bits */
#define ENNMI               (0x0001)    /* Enable NMI interruption of DMA */
#define ROUNDROBIN          (0x0002)    /* Round-Robin DMA channel priorities */
#define DMARMWDIS           (0x0004)    /* Inhibited DMA transfers during read-modify-write CPU operations */

/* DMACTL4 Control Bits */
#define ENNMI_L             (0x0001)    /* Enable NMI interruption of DMA */
#define ROUNDROBIN_L        (0x0002)    /* Round-Robin DMA channel priorities */
#define DMARMWDIS_L         (0x0004)    /* Inhibited DMA transfers during read-modify-write CPU operations */

/* DMACTL4 Control Bits */


/* DMAxCTL Control Bits */
#define DMAREQ              (0x0001)    /* Initiate DMA transfer with DMATSEL */
#define DMAABORT            (0x0002)    /* DMA transfer aborted by NMI */
#define DMAIE               (0x0004)    /* DMA interrupt enable */
#define DMAIFG              (0x0008)    /* DMA interrupt flag */
#define DMAEN               (0x0010)    /* DMA enable */
#define DMALEVEL            (0x0020)    /* DMA level sensitive trigger select */
#define DMASRCBYTE          (0x0040)    /* DMA source byte */
#define DMADSTBYTE          (0x0080)    /* DMA destination byte */
#define DMASRCINCR0         (0x0100)    /* DMA source increment bit 0 */
#define DMASRCINCR1         (0x0200)    /* DMA source increment bit 1 */
#define DMADSTINCR0         (0x0400)    /* DMA destination increment bit 0 */
#define DMADSTINCR1         (0x0800)    /* DMA destination increment bit 1 */
#define DMADT0              (0x1000)    /* DMA transfer mode bit 0 */
#define DMADT1              (0x2000)    /* DMA transfer mode bit 1 */
#define DMADT2              (0x4000)    /* DMA transfer mode bit 2 */

/* DMAxCTL Control Bits */
#define DMAREQ_L            (0x0001)    /* Initiate DMA transfer with DMATSEL */
#define DMAABORT_L          (0x0002)    /* DMA transfer aborted by NMI */
#define DMAIE_L             (0x0004)    /* DMA interrupt enable */
#define DMAIFG_L            (0x0008)    /* DMA interrupt flag */
#define DMAEN_L             (0x0010)    /* DMA enable */
#define DMALEVEL_L          (0x0020)    /* DMA level sensitive trigger select */
#define DMASRCBYTE_L        (0x0040)    /* DMA source byte */
#define DMADSTBYTE_L        (0x0080)    /* DMA destination byte */

/* DMAxCTL Control Bits */
#define DMASRCINCR0_H       (0x0001)    /* DMA source increment bit 0 */
#define DMASRCINCR1_H       (0x0002)    /* DMA source increment bit 1 */
#define DMADSTINCR0_H       (0x0004)    /* DMA destination increment bit 0 */
#define DMADSTINCR1_H       (0x0008)    /* DMA destination increment bit 1 */
#define DMADT0_H            (0x0010)    /* DMA transfer mode bit 0 */
#define DMADT1_H            (0x0020)    /* DMA transfer mode bit 1 */
#define DMADT2_H            (0x0040)    /* DMA transfer mode bit 2 */

#define DMASWDW             (0U*0x0040)  /* DMA transfer: source word to destination word */
#define DMASBDW             (1U*0x0040)  /* DMA transfer: source byte to destination word */
#define DMASWDB             (2U*0x0040)  /* DMA transfer: source word to destination byte */
#define DMASBDB             (3U*0x0040)  /* DMA transfer: source byte to destination byte */

#define DMASRCINCR_0        (0U*0x0100)  /* DMA source increment 0: source address unchanged */
#define DMASRCINCR_1        (1U*0x0100)  /* DMA source increment 1: source address unchanged */
#define DMASRCINCR_2        (2U*0x0100)  /* DMA source increment 2: source address decremented */
#define DMASRCINCR_3        (3U*0x0100)  /* DMA source increment 3: source address incremented */

#define DMADSTINCR_0        (0U*0x0400)  /* DMA destination increment 0: destination address unchanged */
#define DMADSTINCR_1        (1U*0x0400)  /* DMA destination increment 1: destination address unchanged */
#define DMADSTINCR_2        (2U*0x0400)  /* DMA destination increment 2: destination address decremented */
#define DMADSTINCR_3        (3U*0x0400)  /* DMA destination increment 3: destination address incremented */

#define DMADT_0             (0U*0x1000)  /* DMA transfer mode 0: Single transfer */
#define DMADT_1             (1U*0x1000)  /* DMA transfer mode 1: Block transfer */
#define DMADT_2             (2U*0x1000)  /* DMA transfer mode 2: Burst-Block transfer */
#define DMADT_3             (3U*0x1000)  /* DMA transfer mode 3: Burst-Block transfer */
#define DMADT_4             (4U*0x1000)  /* DMA transfer mode 4: Repeated Single transfer */
#define DMADT_5             (5U*0x1000)  /* DMA transfer mode 5: Repeated Block transfer */
#define DMADT_6             (6U*0x1000)  /* DMA transfer mode 6: Repeated Burst-Block transfer */
#define DMADT_7             (7U*0x1000)  /* DMA transfer mode 7: Repeated Burst-Block transfer */

/* DMAIV Definitions */
#define DMAIV_NONE           (0x0000)    /* No Interrupt pending */
#define DMAIV_DMA0IFG        (0x0002)    /* DMA0IFG*/
#define DMAIV_DMA1IFG        (0x0004)    /* DMA1IFG*/
#define DMAIV_DMA2IFG        (0x0006)    /* DMA2IFG*/

#define DMA0TSEL_0          (0U*0x0001)  /* DMA channel 0 transfer select 0:  DMA_REQ (sw) */
#define DMA0TSEL_1          (1U*0x0001)  /* DMA channel 0 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA0TSEL_2          (2U*0x0001)  /* DMA channel 0 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA0TSEL_3          (3U*0x0001)  /* DMA channel 0 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA0TSEL_4          (4U*0x0001)  /* DMA channel 0 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA0TSEL_5          (5U*0x0001)  /* DMA channel 0 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA0TSEL_6          (6U*0x0001)  /* DMA channel 0 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA0TSEL_7          (7U*0x0001)  /* DMA channel 0 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA0TSEL_8          (8U*0x0001)  /* DMA channel 0 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA0TSEL_9          (9U*0x0001)  /* DMA channel 0 transfer select 9:  Reserved */
#define DMA0TSEL_10         (10U*0x0001) /* DMA channel 0 transfer select 10: Reserved */
#define DMA0TSEL_11         (11U*0x0001) /* DMA channel 0 transfer select 11: Reserved */
#define DMA0TSEL_12         (12U*0x0001) /* DMA channel 0 transfer select 12: Reserved */
#define DMA0TSEL_13         (13U*0x0001) /* DMA channel 0 transfer select 13: Reserved */
#define DMA0TSEL_14         (14U*0x0001) /* DMA channel 0 transfer select 14: Reserved */
#define DMA0TSEL_15         (15U*0x0001) /* DMA channel 0 transfer select 15: Reserved */
#define DMA0TSEL_16         (16U*0x0001) /* DMA channel 0 transfer select 16: USCIA0 receive */
#define DMA0TSEL_17         (17U*0x0001) /* DMA channel 0 transfer select 17: USCIA0 transmit */
#define DMA0TSEL_18         (18U*0x0001) /* DMA channel 0 transfer select 18: USCIB0 receive */
#define DMA0TSEL_19         (19U*0x0001) /* DMA channel 0 transfer select 19: USCIB0 transmit */
#define DMA0TSEL_20         (20U*0x0001) /* DMA channel 0 transfer select 20: USCIA1 receive */
#define DMA0TSEL_21         (21U*0x0001) /* DMA channel 0 transfer select 21: USCIA1 transmit */
#define DMA0TSEL_22         (22U*0x0001) /* DMA channel 0 transfer select 22: USCIB1 receive */
#define DMA0TSEL_23         (23U*0x0001) /* DMA channel 0 transfer select 23: USCIB1 transmit */
#define DMA0TSEL_24         (24U*0x0001) /* DMA channel 0 transfer select 24: ADC12IFGx */
#define DMA0TSEL_25         (25U*0x0001) /* DMA channel 0 transfer select 25: Reserved */
#define DMA0TSEL_26         (26U*0x0001) /* DMA channel 0 transfer select 26: Reserved */
#define DMA0TSEL_27         (27U*0x0001) /* DMA channel 0 transfer select 27: USB FNRXD */
#define DMA0TSEL_28         (28U*0x0001) /* DMA channel 0 transfer select 28: USB ready */
#define DMA0TSEL_29         (29U*0x0001) /* DMA channel 0 transfer select 29: Multiplier ready */
#define DMA0TSEL_30         (30U*0x0001) /* DMA channel 0 transfer select 30: previous DMA channel DMA2IFG */
#define DMA0TSEL_31         (31U*0x0001) /* DMA channel 0 transfer select 31: ext. Trigger (DMAE0) */

#define DMA1TSEL_0          (0U*0x0100)  /* DMA channel 1 transfer select 0:  DMA_REQ (sw) */
#define DMA1TSEL_1          (1U*0x0100)  /* DMA channel 1 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA1TSEL_2          (2U*0x0100)  /* DMA channel 1 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA1TSEL_3          (3U*0x0100)  /* DMA channel 1 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA1TSEL_4          (4U*0x0100)  /* DMA channel 1 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA1TSEL_5          (5U*0x0100)  /* DMA channel 1 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA1TSEL_6          (6U*0x0100)  /* DMA channel 1 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA1TSEL_7          (7U*0x0100)  /* DMA channel 1 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA1TSEL_8          (8U*0x0100)  /* DMA channel 1 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA1TSEL_9          (9U*0x0100)  /* DMA channel 1 transfer select 9:  Reserved */
#define DMA1TSEL_10         (10U*0x0100) /* DMA channel 1 transfer select 10: Reserved */
#define DMA1TSEL_11         (11U*0x0100) /* DMA channel 1 transfer select 11: Reserved */
#define DMA1TSEL_12         (12U*0x0100) /* DMA channel 1 transfer select 12: Reserved */
#define DMA1TSEL_13         (13U*0x0100) /* DMA channel 1 transfer select 13: Reserved */
#define DMA1TSEL_14         (14U*0x0100) /* DMA channel 1 transfer select 14: Reserved */
#define DMA1TSEL_15         (15U*0x0100) /* DMA channel 1 transfer select 15: Reserved */
#define DMA1TSEL_16         (16U*0x0100) /* DMA channel 1 transfer select 16: USCIA0 receive */
#define DMA1TSEL_17         (17U*0x0100) /* DMA channel 1 transfer select 17: USCIA0 transmit */
#define DMA1TSEL_18         (18U*0x0100) /* DMA channel 1 transfer select 18: USCIB0 receive */
#define DMA1TSEL_19         (19U*0x0100) /* DMA channel 1 transfer select 19: USCIB0 transmit */
#define DMA1TSEL_20         (20U*0x0100) /* DMA channel 1 transfer select 20: USCIA1 receive */
#define DMA1TSEL_21         (21U*0x0100) /* DMA channel 1 transfer select 21: USCIA1 transmit */
#define DMA1TSEL_22         (22U*0x0100) /* DMA channel 1 transfer select 22: USCIB1 receive */
#define DMA1TSEL_23         (23U*0x0100) /* DMA channel 1 transfer select 23: USCIB1 transmit */
#define DMA1TSEL_24         (24U*0x0100) /* DMA channel 1 transfer select 24: ADC12IFGx */
#define DMA1TSEL_25         (25U*0x0100) /* DMA channel 1 transfer select 25: Reserved */
#define DMA1TSEL_26         (26U*0x0100) /* DMA channel 1 transfer select 26: Reserved */
#define DMA1TSEL_27         (27U*0x0100) /* DMA channel 1 transfer select 27: USB FNRXD */
#define DMA1TSEL_28         (28U*0x0100) /* DMA channel 1 transfer select 28: USB ready */
#define DMA1TSEL_29         (29U*0x0100) /* DMA channel 1 transfer select 29: Multiplier ready */
#define DMA1TSEL_30         (30U*0x0100) /* DMA channel 1 transfer select 30: previous DMA channel DMA0IFG */
#define DMA1TSEL_31         (31U*0x0100) /* DMA channel 1 transfer select 31: ext. Trigger (DMAE0) */

#define DMA2TSEL_0          (0U*0x0001)  /* DMA channel 2 transfer select 0:  DMA_REQ (sw) */
#define DMA2TSEL_1          (1U*0x0001)  /* DMA channel 2 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA2TSEL_2          (2U*0x0001)  /* DMA channel 2 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA2TSEL_3          (3U*0x0001)  /* DMA channel 2 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA2TSEL_4          (4U*0x0001)  /* DMA channel 2 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA2TSEL_5          (5U*0x0001)  /* DMA channel 2 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA2TSEL_6          (6U*0x0001)  /* DMA channel 2 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA2TSEL_7          (7U*0x0001)  /* DMA channel 2 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA2TSEL_8          (8U*0x0001)  /* DMA channel 2 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA2TSEL_9          (9U*0x0001)  /* DMA channel 2 transfer select 9:  Reserved */
#define DMA2TSEL_10         (10U*0x0001) /* DMA channel 2 transfer select 10: Reserved */
#define DMA2TSEL_11         (11U*0x0001) /* DMA channel 2 transfer select 11: Reserved */
#define DMA2TSEL_12         (12U*0x0001) /* DMA channel 2 transfer select 12: Reserved */
#define DMA2TSEL_13         (13U*0x0001) /* DMA channel 2 transfer select 13: Reserved */
#define DMA2TSEL_14         (14U*0x0001) /* DMA channel 2 transfer select 14: Reserved */
#define DMA2TSEL_15         (15U*0x0001) /* DMA channel 2 transfer select 15: Reserved */
#define DMA2TSEL_16         (16U*0x0001) /* DMA channel 2 transfer select 16: USCIA0 receive */
#define DMA2TSEL_17         (17U*0x0001) /* DMA channel 2 transfer select 17: USCIA0 transmit */
#define DMA2TSEL_18         (18U*0x0001) /* DMA channel 2 transfer select 18: USCIB0 receive */
#define DMA2TSEL_19         (19U*0x0001) /* DMA channel 2 transfer select 19: USCIB0 transmit */
#define DMA2TSEL_20         (20U*0x0001) /* DMA channel 2 transfer select 20: USCIA1 receive */
#define DMA2TSEL_21         (21U*0x0001) /* DMA channel 2 transfer select 21: USCIA1 transmit */
#define DMA2TSEL_22         (22U*0x0001) /* DMA channel 2 transfer select 22: USCIB1 receive */
#define DMA2TSEL_23         (23U*0x0001) /* DMA channel 2 transfer select 23: USCIB1 transmit */
#define DMA2TSEL_24         (24U*0x0001) /* DMA channel 2 transfer select 24: ADC12IFGx */
#define DMA2TSEL_25         (25U*0x0001) /* DMA channel 2 transfer select 25: Reserved */
#define DMA2TSEL_26         (26U*0x0001) /* DMA channel 2 transfer select 26: Reserved */
#define DMA2TSEL_27         (27U*0x0001) /* DMA channel 2 transfer select 27: USB FNRXD */
#define DMA2TSEL_28         (28U*0x0001) /* DMA channel 2 transfer select 28: USB ready */
#define DMA2TSEL_29         (29U*0x0001) /* DMA channel 2 transfer select 29: Multiplier ready */
#define DMA2TSEL_30         (30U*0x0001) /* DMA channel 2 transfer select 30: previous DMA channel DMA1IFG */
#define DMA2TSEL_31         (31U*0x0001) /* DMA channel 2 transfer select 31: ext. Trigger (DMAE0) */

#define DMA0TSEL__DMA_REQ   (0U*0x0001)  /* DMA channel 0 transfer select 0:  DMA_REQ (sw) */
#define DMA0TSEL__TA0CCR0   (1U*0x0001)  /* DMA channel 0 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA0TSEL__TA0CCR2   (2U*0x0001)  /* DMA channel 0 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA0TSEL__TA1CCR0   (3U*0x0001)  /* DMA channel 0 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA0TSEL__TA1CCR2   (4U*0x0001)  /* DMA channel 0 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA0TSEL__TA2CCR0   (5U*0x0001)  /* DMA channel 0 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA0TSEL__TA2CCR2   (6U*0x0001)  /* DMA channel 0 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA0TSEL__TB0CCR0   (7U*0x0001)  /* DMA channel 0 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA0TSEL__TB0CCR2   (8U*0x0001)  /* DMA channel 0 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA0TSEL__RES9      (9U*0x0001)  /* DMA channel 0 transfer select 9:  Reserved */
#define DMA0TSEL__RES10     (10U*0x0001) /* DMA channel 0 transfer select 10: Reserved */
#define DMA0TSEL__RES11     (11U*0x0001) /* DMA channel 0 transfer select 11: Reserved */
#define DMA0TSEL__RES12     (12U*0x0001) /* DMA channel 0 transfer select 12: Reserved */
#define DMA0TSEL__RES13     (13U*0x0001) /* DMA channel 0 transfer select 13: Reserved */
#define DMA0TSEL__RES14     (14U*0x0001) /* DMA channel 0 transfer select 14: Reserved */
#define DMA0TSEL__RES15     (15U*0x0001) /* DMA channel 0 transfer select 15: Reserved */
#define DMA0TSEL__USCIA0RX  (16U*0x0001) /* DMA channel 0 transfer select 16: USCIA0 receive */
#define DMA0TSEL__USCIA0TX  (17U*0x0001) /* DMA channel 0 transfer select 17: USCIA0 transmit */
#define DMA0TSEL__USCIB0RX  (18U*0x0001) /* DMA channel 0 transfer select 18: USCIB0 receive */
#define DMA0TSEL__USCIB0TX  (19U*0x0001) /* DMA channel 0 transfer select 19: USCIB0 transmit */
#define DMA0TSEL__USCIA1RX  (20U*0x0001) /* DMA channel 0 transfer select 20: USCIA1 receive */
#define DMA0TSEL__USCIA1TX  (21U*0x0001) /* DMA channel 0 transfer select 21: USCIA1 transmit */
#define DMA0TSEL__USCIB1RX  (22U*0x0001) /* DMA channel 0 transfer select 22: USCIB1 receive */
#define DMA0TSEL__USCIB1TX  (23U*0x0001) /* DMA channel 0 transfer select 23: USCIB1 transmit */
#define DMA0TSEL__ADC12IFG  (24U*0x0001) /* DMA channel 0 transfer select 24: ADC12IFGx */
#define DMA0TSEL__RES25     (25U*0x0001) /* DMA channel 0 transfer select 25: Reserved */
#define DMA0TSEL__RES26     (26U*0x0001) /* DMA channel 0 transfer select 26: Reserved */
#define DMA0TSEL__USB_FNRXD (27U*0x0001) /* DMA channel 0 transfer select 27: USB FNRXD */
#define DMA0TSEL__USB_READY (28U*0x0001) /* DMA channel 0 transfer select 28: USB ready */
#define DMA0TSEL__MPY       (29U*0x0001) /* DMA channel 0 transfer select 29: Multiplier ready */
#define DMA0TSEL__DMA2IFG   (30U*0x0001) /* DMA channel 0 transfer select 30: previous DMA channel DMA2IFG */
#define DMA0TSEL__DMAE0     (31U*0x0001) /* DMA channel 0 transfer select 31: ext. Trigger (DMAE0) */
               
#define DMA1TSEL__DMA_REQ   (0U*0x0100)  /* DMA channel 1 transfer select 0:  DMA_REQ (sw) */
#define DMA1TSEL__TA0CCR0   (1U*0x0100)  /* DMA channel 1 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA1TSEL__TA0CCR2   (2U*0x0100)  /* DMA channel 1 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA1TSEL__TA1CCR0   (3U*0x0100)  /* DMA channel 1 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA1TSEL__TA1CCR2   (4U*0x0100)  /* DMA channel 1 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA1TSEL__TA2CCR0   (5U*0x0100)  /* DMA channel 1 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA1TSEL__TA2CCR2   (6U*0x0100)  /* DMA channel 1 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA1TSEL__TB0CCR0   (7U*0x0100)  /* DMA channel 1 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA1TSEL__TB0CCR2   (8U*0x0100)  /* DMA channel 1 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA1TSEL__RES9      (9U*0x0100)  /* DMA channel 1 transfer select 9:  Reserved */
#define DMA1TSEL__RES10     (10U*0x0100) /* DMA channel 1 transfer select 10: Reserved */
#define DMA1TSEL__RES11     (11U*0x0100) /* DMA channel 1 transfer select 11: Reserved */
#define DMA1TSEL__RES12     (12U*0x0100) /* DMA channel 1 transfer select 12: Reserved */
#define DMA1TSEL__RES13     (13U*0x0100) /* DMA channel 1 transfer select 13: Reserved */
#define DMA1TSEL__RES14     (14U*0x0100) /* DMA channel 1 transfer select 14: Reserved */
#define DMA1TSEL__RES15     (15U*0x0100) /* DMA channel 1 transfer select 15: Reserved */
#define DMA1TSEL__USCIA0RX  (16U*0x0100) /* DMA channel 1 transfer select 16: USCIA0 receive */
#define DMA1TSEL__USCIA0TX  (17U*0x0100) /* DMA channel 1 transfer select 17: USCIA0 transmit */
#define DMA1TSEL__USCIB0RX  (18U*0x0100) /* DMA channel 1 transfer select 18: USCIB0 receive */
#define DMA1TSEL__USCIB0TX  (19U*0x0100) /* DMA channel 1 transfer select 19: USCIB0 transmit */
#define DMA1TSEL__USCIA1RX  (20U*0x0100) /* DMA channel 1 transfer select 20: USCIA1 receive */
#define DMA1TSEL__USCIA1TX  (21U*0x0100) /* DMA channel 1 transfer select 21: USCIA1 transmit */
#define DMA1TSEL__USCIB1RX  (22U*0x0100) /* DMA channel 1 transfer select 22: USCIB1 receive */
#define DMA1TSEL__USCIB1TX  (23U*0x0100) /* DMA channel 1 transfer select 23: USCIB1 transmit */
#define DMA1TSEL__ADC12IFG  (24U*0x0100) /* DMA channel 1 transfer select 24: ADC12IFGx */
#define DMA1TSEL__RES25     (25U*0x0100) /* DMA channel 1 transfer select 25: Reserved */
#define DMA1TSEL__RES26     (26U*0x0100) /* DMA channel 1 transfer select 26: Reserved */
#define DMA1TSEL__USB_FNRXD (27U*0x0100) /* DMA channel 1 transfer select 27: USB FNRXD */
#define DMA1TSEL__USB_READY (28U*0x0100) /* DMA channel 1 transfer select 28: USB ready */
#define DMA1TSEL__MPY       (29U*0x0100) /* DMA channel 1 transfer select 29: Multiplier ready */
#define DMA1TSEL__DMA0IFG   (30U*0x0100) /* DMA channel 1 transfer select 30: previous DMA channel DMA0IFG */
#define DMA1TSEL__DMAE0     (31U*0x0100) /* DMA channel 1 transfer select 31: ext. Trigger (DMAE0) */
                
#define DMA2TSEL__DMA_REQ   (0U*0x0001)  /* DMA channel 2 transfer select 0:  DMA_REQ (sw) */
#define DMA2TSEL__TA0CCR0   (1U*0x0001)  /* DMA channel 2 transfer select 1:  Timer0_A (TA0CCR0.IFG) */
#define DMA2TSEL__TA0CCR2   (2U*0x0001)  /* DMA channel 2 transfer select 2:  Timer0_A (TA0CCR2.IFG) */
#define DMA2TSEL__TA1CCR0   (3U*0x0001)  /* DMA channel 2 transfer select 3:  Timer1_A (TA1CCR0.IFG) */
#define DMA2TSEL__TA1CCR2   (4U*0x0001)  /* DMA channel 2 transfer select 4:  Timer1_A (TA1CCR2.IFG) */
#define DMA2TSEL__TA2CCR0   (5U*0x0001)  /* DMA channel 2 transfer select 5:  Timer2_A (TA2CCR0.IFG) */
#define DMA2TSEL__TA2CCR2   (6U*0x0001)  /* DMA channel 2 transfer select 6:  Timer2_A (TA2CCR2.IFG) */
#define DMA2TSEL__TB0CCR0   (7U*0x0001)  /* DMA channel 2 transfer select 7:  TimerB (TB0CCR0.IFG) */
#define DMA2TSEL__TB0CCR2   (8U*0x0001)  /* DMA channel 2 transfer select 8:  TimerB (TB0CCR2.IFG) */
#define DMA2TSEL__RES9      (9U*0x0001)  /* DMA channel 2 transfer select 9:  Reserved */
#define DMA2TSEL__RES10     (10U*0x0001) /* DMA channel 2 transfer select 10: Reserved */
#define DMA2TSEL__RES11     (11U*0x0001) /* DMA channel 2 transfer select 11: Reserved */
#define DMA2TSEL__RES12     (12U*0x0001) /* DMA channel 2 transfer select 12: Reserved */
#define DMA2TSEL__RES13     (13U*0x0001) /* DMA channel 2 transfer select 13: Reserved */
#define DMA2TSEL__RES14     (14U*0x0001) /* DMA channel 2 transfer select 14: Reserved */
#define DMA2TSEL__RES15     (15U*0x0001) /* DMA channel 2 transfer select 15: Reserved */
#define DMA2TSEL__USCIA0RX  (16U*0x0001) /* DMA channel 2 transfer select 16: USCIA0 receive */
#define DMA2TSEL__USCIA0TX  (17U*0x0001) /* DMA channel 2 transfer select 17: USCIA0 transmit */
#define DMA2TSEL__USCIB0RX  (18U*0x0001) /* DMA channel 2 transfer select 18: USCIB0 receive */
#define DMA2TSEL__USCIB0TX  (19U*0x0001) /* DMA channel 2 transfer select 19: USCIB0 transmit */
#define DMA2TSEL__USCIA1RX  (20U*0x0001) /* DMA channel 2 transfer select 20: USCIA1 receive */
#define DMA2TSEL__USCIA1TX  (21U*0x0001) /* DMA channel 2 transfer select 21: USCIA1 transmit */
#define DMA2TSEL__USCIB1RX  (22U*0x0001) /* DMA channel 2 transfer select 22: USCIB1 receive */
#define DMA2TSEL__USCIB1TX  (23U*0x0001) /* DMA channel 2 transfer select 23: USCIB1 transmit */
#define DMA2TSEL__ADC12IFG  (24U*0x0001) /* DMA channel 2 transfer select 24: ADC12IFGx */
#define DMA2TSEL__RES25     (25U*0x0001) /* DMA channel 2 transfer select 25: Reserved */
#define DMA2TSEL__RES26     (26U*0x0001) /* DMA channel 2 transfer select 26: Reserved */
#define DMA2TSEL__USB_FNRXD (27U*0x0001) /* DMA channel 2 transfer select 27: USB FNRXD */
#define DMA2TSEL__USB_READY (28U*0x0001) /* DMA channel 2 transfer select 28: USB ready */
#define DMA2TSEL__MPY       (29U*0x0001) /* DMA channel 2 transfer select 29: Multiplier ready */
#define DMA2TSEL__DMA1IFG   (30U*0x0001) /* DMA channel 2 transfer select 30: previous DMA channel DMA1IFG */
#define DMA2TSEL__DMAE0     (31U*0x0001) /* DMA channel 2 transfer select 31: ext. Trigger (DMAE0) */
                
/*************************************************************
* Flash Memory
*************************************************************/
#define __MSP430_HAS_FLASH__         /* Definition to show that Module is available */

#define FCTL1_                0x0140    /* FLASH Control 1 */
sfrb(FCTL1_L, FCTL1_);
sfrb(FCTL1_H, FCTL1_+1);
sfrw(FCTL1, FCTL1_);
//sfrbw    FCTL2               (0x0142)  /* FLASH Control 2 */
#define FCTL3_                0x0144    /* FLASH Control 3 */
sfrb(FCTL3_L, FCTL3_);
sfrb(FCTL3_H, FCTL3_+1);
sfrw(FCTL3, FCTL3_);
#define FCTL4_                0x0146    /* FLASH Control 4 */
sfrb(FCTL4_L, FCTL4_);
sfrb(FCTL4_H, FCTL4_+1);
sfrw(FCTL4, FCTL4_);

#define FRPW                (0x9600)  /* Flash password returned by read */
#define FWPW                (0xA500)  /* Flash password for write */
#define FXPW                (0x3300)  /* for use with XOR instruction */
#define FRKEY               (0x9600)  /* (legacy definition) Flash key returned by read */
#define FWKEY               (0xA500)  /* (legacy definition) Flash key for write */
#define FXKEY               (0x3300)  /* (legacy definition) for use with XOR instruction */

/* FCTL1 Control Bits */
//#define RESERVED            (0x0001)  /* Reserved */
#define ERASE               (0x0002)  /* Enable bit for Flash segment erase */
#define MERAS               (0x0004)  /* Enable bit for Flash mass erase */
//#define RESERVED            (0x0008)  /* Reserved */
//#define RESERVED            (0x0010)  /* Reserved */
#define SWRT                (0x0020)  /* Smart Write enable */
#define WRT                 (0x0040)  /* Enable bit for Flash write */
#define BLKWRT              (0x0080)  /* Enable bit for Flash segment write */

/* FCTL1 Control Bits */
//#define RESERVED            (0x0001)  /* Reserved */
#define ERASE_L             (0x0002)  /* Enable bit for Flash segment erase */
#define MERAS_L             (0x0004)  /* Enable bit for Flash mass erase */
//#define RESERVED            (0x0008)  /* Reserved */
//#define RESERVED            (0x0010)  /* Reserved */
#define SWRT_L              (0x0020)  /* Smart Write enable */
#define WRT_L               (0x0040)  /* Enable bit for Flash write */
#define BLKWRT_L            (0x0080)  /* Enable bit for Flash segment write */

/* FCTL1 Control Bits */
//#define RESERVED            (0x0001)  /* Reserved */
//#define RESERVED            (0x0008)  /* Reserved */
//#define RESERVED            (0x0010)  /* Reserved */

/* FCTL3 Control Bits */
#define BUSY                (0x0001)  /* Flash busy: 1 */
#define KEYV                (0x0002)  /* Flash Key violation flag */
#define ACCVIFG             (0x0004)  /* Flash Access violation flag */
#define WAIT                (0x0008)  /* Wait flag for segment write */
#define LOCK                (0x0010)  /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX                (0x0020)  /* Flash Emergency Exit */
#define LOCKA               (0x0040)  /* Segment A Lock bit: read = 1 - Segment is locked (read only) */
//#define RESERVED            (0x0080)  /* Reserved */

/* FCTL3 Control Bits */
#define BUSY_L              (0x0001)  /* Flash busy: 1 */
#define KEYV_L              (0x0002)  /* Flash Key violation flag */
#define ACCVIFG_L           (0x0004)  /* Flash Access violation flag */
#define WAIT_L              (0x0008)  /* Wait flag for segment write */
#define LOCK_L              (0x0010)  /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX_L              (0x0020)  /* Flash Emergency Exit */
#define LOCKA_L             (0x0040)  /* Segment A Lock bit: read = 1 - Segment is locked (read only) */
//#define RESERVED            (0x0080)  /* Reserved */

/* FCTL3 Control Bits */
//#define RESERVED            (0x0080)  /* Reserved */

/* FCTL4 Control Bits */
#define VPE                 (0x0001)  /* Voltage Changed during Program Error Flag */
#define MGR0                (0x0010)  /* Marginal read 0 mode. */
#define MGR1                (0x0020)  /* Marginal read 1 mode. */
#define LOCKINFO            (0x0080)  /* Lock INFO Memory bit: read = 1 - Segment is locked (read only) */

/* FCTL4 Control Bits */
#define VPE_L               (0x0001)  /* Voltage Changed during Program Error Flag */
#define MGR0_L              (0x0010)  /* Marginal read 0 mode. */
#define MGR1_L              (0x0020)  /* Marginal read 1 mode. */
#define LOCKINFO_L          (0x0080)  /* Lock INFO Memory bit: read = 1 - Segment is locked (read only) */

/* FCTL4 Control Bits */

/************************************************************
* HARDWARE MULTIPLIER 32Bit
************************************************************/
#define __MSP430_HAS_MPY32__          /* Definition to show that Module is available */

#define MPY_                  0x04C0    /* Multiply Unsigned/Operand 1 */
sfrb(MPY_L, MPY_);
sfrb(MPY_H, MPY_+1);
sfrw(MPY, MPY_);
#define MPYS_                 0x04C2    /* Multiply Signed/Operand 1 */
sfrb(MPYS_L, MPYS_);
sfrb(MPYS_H, MPYS_+1);
sfrw(MPYS, MPYS_);
#define MAC_                  0x04C4    /* Multiply Unsigned and Accumulate/Operand 1 */
sfrb(MAC_L, MAC_);
sfrb(MAC_H, MAC_+1);
sfrw(MAC, MAC_);
#define MACS_                 0x04C6    /* Multiply Signed and Accumulate/Operand 1 */
sfrb(MACS_L, MACS_);
sfrb(MACS_H, MACS_+1);
sfrw(MACS, MACS_);
#define OP2_                  0x04C8    /* Operand 2 */
sfrb(OP2_L, OP2_);
sfrb(OP2_H, OP2_+1);
sfrw(OP2, OP2_);
#define RESLO_                0x04CA    /* Result Low Word */
sfrb(RESLO_L, RESLO_);
sfrb(RESLO_H, RESLO_+1);
sfrw(RESLO, RESLO_);
#define RESHI_                0x04CC    /* Result High Word */
sfrb(RESHI_L, RESHI_);
sfrb(RESHI_H, RESHI_+1);
sfrw(RESHI, RESHI_);
#define SUMEXT_               0x04CE    /* Sum Extend */
const_sfrb(SUMEXT_L, SUMEXT_);
const_sfrb(SUMEXT_H, SUMEXT_+1);
const_sfrw(SUMEXT, SUMEXT_);

#define MPY32L_               0x04D0    /* 32-bit operand 1 - multiply - low word */
sfrb(MPY32L_L, MPY32L_);
sfrb(MPY32L_H, MPY32L_+1);
sfrw(MPY32L, MPY32L_);
#define MPY32H_               0x04D2    /* 32-bit operand 1 - multiply - high word */
sfrb(MPY32H_L, MPY32H_);
sfrb(MPY32H_H, MPY32H_+1);
sfrw(MPY32H, MPY32H_);
#define MPYS32L_              0x04D4    /* 32-bit operand 1 - signed multiply - low word */
sfrb(MPYS32L_L, MPYS32L_);
sfrb(MPYS32L_H, MPYS32L_+1);
sfrw(MPYS32L, MPYS32L_);
#define MPYS32H_              0x04D6    /* 32-bit operand 1 - signed multiply - high word */
sfrb(MPYS32H_L, MPYS32H_);
sfrb(MPYS32H_H, MPYS32H_+1);
sfrw(MPYS32H, MPYS32H_);
#define MAC32L_               0x04D8    /* 32-bit operand 1 - multiply accumulate - low word */
sfrb(MAC32L_L, MAC32L_);
sfrb(MAC32L_H, MAC32L_+1);
sfrw(MAC32L, MAC32L_);
#define MAC32H_               0x04DA    /* 32-bit operand 1 - multiply accumulate - high word */
sfrb(MAC32H_L, MAC32H_);
sfrb(MAC32H_H, MAC32H_+1);
sfrw(MAC32H, MAC32H_);
#define MACS32L_              0x04DC    /* 32-bit operand 1 - signed multiply accumulate - low word */
sfrb(MACS32L_L, MACS32L_);
sfrb(MACS32L_H, MACS32L_+1);
sfrw(MACS32L, MACS32L_);
#define MACS32H_              0x04DE    /* 32-bit operand 1 - signed multiply accumulate - high word */
sfrb(MACS32H_L, MACS32H_);
sfrb(MACS32H_H, MACS32H_+1);
sfrw(MACS32H, MACS32H_);
#define OP2L_                 0x04E0    /* 32-bit operand 2 - low word */
sfrb(OP2L_L, OP2L_);
sfrb(OP2L_H, OP2L_+1);
sfrw(OP2L, OP2L_);
#define OP2H_                 0x04E2    /* 32-bit operand 2 - high word */
sfrb(OP2H_L, OP2H_);
sfrb(OP2H_H, OP2H_+1);
sfrw(OP2H, OP2H_);
#define RES0_                 0x04E4    /* 32x32-bit result 0 - least significant word */
sfrb(RES0_L, RES0_);
sfrb(RES0_H, RES0_+1);
sfrw(RES0, RES0_);
#define RES1_                 0x04E6    /* 32x32-bit result 1 */
sfrb(RES1_L, RES1_);
sfrb(RES1_H, RES1_+1);
sfrw(RES1, RES1_);
#define RES2_                 0x04E8    /* 32x32-bit result 2 */
sfrb(RES2_L, RES2_);
sfrb(RES2_H, RES2_+1);
sfrw(RES2, RES2_);
#define RES3_                 0x04EA    /* 32x32-bit result 3 - most significant word */
sfrb(RES3_L, RES3_);
sfrb(RES3_H, RES3_+1);
sfrw(RES3, RES3_);
#define MPY32CTL0_            0x04EC    /* MPY32 Control Register 0 */
sfrb(MPY32CTL0_L, MPY32CTL0_);
sfrb(MPY32CTL0_H, MPY32CTL0_+1);
sfrw(MPY32CTL0, MPY32CTL0_);

#define MPY_B               MPY_L      /* Multiply Unsigned/Operand 1 (Byte Access) */
#define MPYS_B              MPYS_L     /* Multiply Signed/Operand 1 (Byte Access) */
#define MAC_B               MAC_L      /* Multiply Unsigned and Accumulate/Operand 1 (Byte Access) */
#define MACS_B              MACS_L     /* Multiply Signed and Accumulate/Operand 1 (Byte Access) */
#define OP2_B               OP2_L      /* Operand 2 (Byte Access) */
#define MPY32L_B            MPY32L_L   /* 32-bit operand 1 - multiply - low word (Byte Access) */
#define MPY32H_B            MPY32H_L   /* 32-bit operand 1 - multiply - high word (Byte Access) */
#define MPYS32L_B           MPYS32L_L  /* 32-bit operand 1 - signed multiply - low word (Byte Access) */
#define MPYS32H_B           MPYS32H_L  /* 32-bit operand 1 - signed multiply - high word (Byte Access) */
#define MAC32L_B            MAC32L_L   /* 32-bit operand 1 - multiply accumulate - low word (Byte Access) */
#define MAC32H_B            MAC32H_L   /* 32-bit operand 1 - multiply accumulate - high word (Byte Access) */
#define MACS32L_B           MACS32L_L  /* 32-bit operand 1 - signed multiply accumulate - low word (Byte Access) */
#define MACS32H_B           MACS32H_L  /* 32-bit operand 1 - signed multiply accumulate - high word (Byte Access) */
#define OP2L_B              OP2L_L     /* 32-bit operand 2 - low word (Byte Access) */
#define OP2H_B              OP2H_L     /* 32-bit operand 2 - high word (Byte Access) */


/* MPY32CTL0 Control Bits */
#define MPYC                (0x0001)  /* Carry of the multiplier */
//#define RESERVED            (0x0002)  /* Reserved */
#define MPYFRAC             (0x0004)  /* Fractional mode */
#define MPYSAT              (0x0008)  /* Saturation mode */
#define MPYM0               (0x0010)  /* Multiplier mode Bit:0 */
#define MPYM1               (0x0020)  /* Multiplier mode Bit:1 */
#define OP1_32              (0x0040)  /* Bit-width of operand 1 0:16Bit / 1:32Bit */
#define OP2_32              (0x0080)  /* Bit-width of operand 2 0:16Bit / 1:32Bit */
#define MPYDLYWRTEN         (0x0100)  /* Delayed write enable */
#define MPYDLY32            (0x0200)  /* Delayed write mode */

/* MPY32CTL0 Control Bits */
#define MPYC_L              (0x0001)  /* Carry of the multiplier */
//#define RESERVED            (0x0002)  /* Reserved */
#define MPYFRAC_L           (0x0004)  /* Fractional mode */
#define MPYSAT_L            (0x0008)  /* Saturation mode */
#define MPYM0_L             (0x0010)  /* Multiplier mode Bit:0 */
#define MPYM1_L             (0x0020)  /* Multiplier mode Bit:1 */
#define OP1_32_L            (0x0040)  /* Bit-width of operand 1 0:16Bit / 1:32Bit */
#define OP2_32_L            (0x0080)  /* Bit-width of operand 2 0:16Bit / 1:32Bit */

/* MPY32CTL0 Control Bits */
//#define RESERVED            (0x0002)  /* Reserved */
#define MPYDLYWRTEN_H       (0x0001)  /* Delayed write enable */
#define MPYDLY32_H          (0x0002)  /* Delayed write mode */

#define MPYM_0              (0x0000)  /* Multiplier mode: MPY */
#define MPYM_1              (0x0010)  /* Multiplier mode: MPYS */
#define MPYM_2              (0x0020)  /* Multiplier mode: MAC */
#define MPYM_3              (0x0030)  /* Multiplier mode: MACS */
#define MPYM__MPY           (0x0000)  /* Multiplier mode: MPY */
#define MPYM__MPYS          (0x0010)  /* Multiplier mode: MPYS */
#define MPYM__MAC           (0x0020)  /* Multiplier mode: MAC */
#define MPYM__MACS          (0x0030)  /* Multiplier mode: MACS */

/************************************************************
* DIGITAL I/O Port1/2 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT1_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORT2_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORTA_R__        /* Definition to show that Module is available */

#define PAIN_		0x0200    /* Port A Input */
const_sfrb(PAIN_L, PAIN_);
const_sfrb(PAIN_H, PAIN_+1);
const_sfrw(PAIN, PAIN_);
#define PAOUT_		0x0202    /* Port A Output */
sfrb(PAOUT_L, PAOUT_);
sfrb(PAOUT_H, PAOUT_+1);
sfrw(PAOUT, PAOUT_);
#define PADIR_		0x0204    /* Port A Direction */
sfrb(PADIR_L, PADIR_);
sfrb(PADIR_H, PADIR_+1);
sfrw(PADIR, PADIR_);
#define PAREN_		0x0206    /* Port A Resistor Enable */
sfrb(PAREN_L, PAREN_);
sfrb(PAREN_H, PAREN_+1);
sfrw(PAREN, PAREN_);
#define PADS_		0x0208    /* Port A Resistor Drive Strenght */
sfrb(PADS_L, PADS_);
sfrb(PADS_H, PADS_+1);
sfrw(PADS, PADS_);
#define PASEL_		0x020A    /* Port A Selection */
sfrb(PASEL_L, PASEL_);
sfrb(PASEL_H, PASEL_+1);
sfrw(PASEL, PASEL_);
#define PAIES_		0x0218    /* Port A Interrupt Edge Select */
sfrb(PAIES_L, PAIES_);
sfrb(PAIES_H, PAIES_+1);
sfrw(PAIES, PAIES_);
#define PAIE_		0x021A    /* Port A Interrupt Enable */
sfrb(PAIE_L, PAIE_);
sfrb(PAIE_H, PAIE_+1);
sfrw(PAIE, PAIE_);
#define PAIFG_		0x021C    /* Port A Interrupt Flag */
sfrb(PAIFG_L, PAIFG_);
sfrb(PAIFG_H, PAIFG_+1);
sfrw(PAIFG, PAIFG_);



#define P1IV_                 0x020E    /* Port 1 Interrupt Vector Word */
sfrw(P1IV, P1IV_);
#define P2IV_                 0x021E    /* Port 2 Interrupt Vector Word */
sfrw(P2IV, P2IV_);
#define P1IN                (PAIN_L)  /* Port 1 Input */
#define P1OUT               (PAOUT_L) /* Port 1 Output */
#define P1DIR               (PADIR_L) /* Port 1 Direction */
#define P1REN               (PAREN_L) /* Port 1 Resistor Enable */
#define P1DS                (PADS_L)  /* Port 1 Resistor Drive Strenght */
#define P1SEL               (PASEL_L) /* Port 1 Selection */
#define P1IES               (PAIES_L) /* Port 1 Interrupt Edge Select */
#define P1IE                (PAIE_L)  /* Port 1 Interrupt Enable */
#define P1IFG               (PAIFG_L) /* Port 1 Interrupt Flag */

//Definitions for P1IV
#define P1IV_NONE            (0x0000)    /* No Interrupt pending */
#define P1IV_P1IFG0          (0x0002)    /* P1IV P1IFG.0 */
#define P1IV_P1IFG1          (0x0004)    /* P1IV P1IFG.1 */
#define P1IV_P1IFG2          (0x0006)    /* P1IV P1IFG.2 */
#define P1IV_P1IFG3          (0x0008)    /* P1IV P1IFG.3 */
#define P1IV_P1IFG4          (0x000A)    /* P1IV P1IFG.4 */
#define P1IV_P1IFG5          (0x000C)    /* P1IV P1IFG.5 */
#define P1IV_P1IFG6          (0x000E)    /* P1IV P1IFG.6 */
#define P1IV_P1IFG7          (0x0010)    /* P1IV P1IFG.7 */


#define P2IN                (PAIN_H)  /* Port 2 Input */
#define P2OUT               (PAOUT_H) /* Port 2 Output */
#define P2DIR               (PADIR_H) /* Port 2 Direction */
#define P2REN               (PAREN_H) /* Port 2 Resistor Enable */
#define P2DS                (PADS_H)  /* Port 2 Resistor Drive Strenght */
#define P2SEL               (PASEL_H) /* Port 2 Selection */
#define P2IES               (PAIES_H) /* Port 2 Interrupt Edge Select */
#define P2IE                (PAIE_H)  /* Port 2 Interrupt Enable */
#define P2IFG               (PAIFG_H) /* Port 2 Interrupt Flag */

//Definitions for P2IV
#define P2IV_NONE            (0x0000)    /* No Interrupt pending */
#define P2IV_P2IFG0          (0x0002)    /* P2IV P2IFG.0 */
#define P2IV_P2IFG1          (0x0004)    /* P2IV P2IFG.1 */
#define P2IV_P2IFG2          (0x0006)    /* P2IV P2IFG.2 */
#define P2IV_P2IFG3          (0x0008)    /* P2IV P2IFG.3 */
#define P2IV_P2IFG4          (0x000A)    /* P2IV P2IFG.4 */
#define P2IV_P2IFG5          (0x000C)    /* P2IV P2IFG.5 */
#define P2IV_P2IFG6          (0x000E)    /* P2IV P2IFG.6 */
#define P2IV_P2IFG7          (0x0010)    /* P2IV P2IFG.7 */

                       
                   
/************************************************************
* DIGITAL I/O Port3/4 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT3_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORT4_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORTB_R__        /* Definition to show that Module is available */

#define PBIN_		0x0220    /* Port B Input */
const_sfrb(PBIN_L, PBIN_);
const_sfrb(PBIN_H, PBIN_+1);
const_sfrw(PBIN, PBIN_);
#define PBOUT_		0x0222    /* Port B Output */
sfrb(PBOUT_L, PBOUT_);
sfrb(PBOUT_H, PBOUT_+1);
sfrw(PBOUT, PBOUT_);
#define PBDIR_		0x0224    /* Port B Direction */
sfrb(PBDIR_L, PBDIR_);
sfrb(PBDIR_H, PBDIR_+1);
sfrw(PBDIR, PBDIR_);
#define PBREN_		0x0226    /* Port B Resistor Enable */
sfrb(PBREN_L, PBREN_);
sfrb(PBREN_H, PBREN_+1);
sfrw(PBREN, PBREN_);
#define PBDS_		0x0228    /* Port B Resistor Drive Strenght */
sfrb(PBDS_L, PBDS_);
sfrb(PBDS_H, PBDS_+1);
sfrw(PBDS, PBDS_);
#define PBSEL_		0x022A    /* Port B Selection */
sfrb(PBSEL_L, PBSEL_);
sfrb(PBSEL_H, PBSEL_+1);
sfrw(PBSEL, PBSEL_);



#define P3IN                (PBIN_L)  /* Port 3 Input */
#define P3OUT               (PBOUT_L) /* Port 3 Output */
#define P3DIR               (PBDIR_L) /* Port 3 Direction */
#define P3REN               (PBREN_L) /* Port 3 Resistor Enable */
#define P3DS                (PBDS_L)  /* Port 3 Resistor Drive Strenght */
#define P3SEL               (PBSEL_L) /* Port 3 Selection */


#define P4IN                (PBIN_H)  /* Port 4 Input */
#define P4OUT               (PBOUT_H) /* Port 4 Output */
#define P4DIR               (PBDIR_H) /* Port 4 Direction */
#define P4REN               (PBREN_H) /* Port 4 Resistor Enable */
#define P4DS                (PBDS_H)  /* Port 4 Resistor Drive Strenght */
#define P4SEL               (PBSEL_H) /* Port 4 Selection */
                       
                   
/************************************************************
* DIGITAL I/O Port5/6 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT5_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORT6_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORTC_R__        /* Definition to show that Module is available */

#define PCIN_                 0x0240    /* Port C Input */
const_sfrb(PCIN_L, PCIN_);
const_sfrb(PCIN_H, PCIN_+1);
const_sfrw(PCIN, PCIN_);
#define PCOUT_                0x0242    /* Port C Output */
sfrb(PCOUT_L, PCOUT_);
sfrb(PCOUT_H, PCOUT_+1);
sfrw(PCOUT, PCOUT_);
#define PCDIR_                0x0244    /* Port C Direction */
sfrb(PCDIR_L, PCDIR_);
sfrb(PCDIR_H, PCDIR_+1);
sfrw(PCDIR, PCDIR_);
#define PCREN_                0x0246    /* Port C Resistor Enable */
sfrb(PCREN_L, PCREN_);
sfrb(PCREN_H, PCREN_+1);
sfrw(PCREN, PCREN_);
#define PCDS_                 0x0248    /* Port C Resistor Drive Strenght */
sfrb(PCDS_L, PCDS_);
sfrb(PCDS_H, PCDS_+1);
sfrw(PCDS, PCDS_);
#define PCSEL_                0x024A    /* Port C Selection */
sfrb(PCSEL_L, PCSEL_);
sfrb(PCSEL_H, PCSEL_+1);
sfrw(PCSEL, PCSEL_);



#define P5IN                (PCIN_L)  /* Port 5 Input */
#define P5OUT               (PCOUT_L) /* Port 5 Output */
#define P5DIR               (PCDIR_L) /* Port 5 Direction */
#define P5REN               (PCREN_L) /* Port 5 Resistor Enable */
#define P5DS                (PCDS_L)  /* Port 5 Resistor Drive Strenght */
#define P5SEL               (PCSEL_L) /* Port 5 Selection */


#define P6IN                (PCIN_H)  /* Port 6 Input */
#define P6OUT               (PCOUT_H) /* Port 6 Output */
#define P6DIR               (PCDIR_H) /* Port 6 Direction */
#define P6REN               (PCREN_H) /* Port 6 Resistor Enable */
#define P6DS                (PCDS_H)  /* Port 6 Resistor Drive Strenght */
#define P6SEL               (PCSEL_H) /* Port 6 Selection */
                       
                   
/************************************************************
* DIGITAL I/O Port7/8 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT7_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORT8_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORTD_R__        /* Definition to show that Module is available */

#define PDIN_                 0x0260    /* Port D Input */
const_sfrb(PDIN_L, PDIN_);
const_sfrb(PDIN_H, PDIN_+1);
const_sfrw(PDIN, PDIN_);
#define PDOUT_                0x0262    /* Port D Output */
sfrb(PDOUT_L, PDOUT_);
sfrb(PDOUT_H, PDOUT_+1);
sfrw(PDOUT, PDOUT_);
#define PDDIR_                0x0264    /* Port D Direction */
sfrb(PDDIR_L, PDDIR_);
sfrb(PDDIR_H, PDDIR_+1);
sfrw(PDDIR, PDDIR_);
#define PDREN_                0x0266    /* Port D Resistor Enable */
sfrb(PDREN_L, PDREN_);
sfrb(PDREN_H, PDREN_+1);
sfrw(PDREN, PDREN_);
#define PDDS_                 0x0268    /* Port D Resistor Drive Strenght */
sfrb(PDDS_L, PDDS_);
sfrb(PDDS_H, PDDS_+1);
sfrw(PDDS, PDDS_);
#define PDSEL_                0x026A    /* Port D Selection */
sfrb(PDSEL_L, PDSEL_);
sfrb(PDSEL_H, PDSEL_+1);
sfrw(PDSEL, PDSEL_);



#define P7IN                (PDIN_L)  /* Port 7 Input */
#define P7OUT               (PDOUT_L) /* Port 7 Output */
#define P7DIR               (PDDIR_L) /* Port 7 Direction */
#define P7REN               (PDREN_L) /* Port 7 Resistor Enable */
#define P7DS                (PDDS_L)  /* Port 7 Resistor Drive Strenght */
#define P7SEL               (PDSEL_L) /* Port 7 Selection */


#define P8IN                (PDIN_H)  /* Port 8 Input */
#define P8OUT               (PDOUT_H) /* Port 8 Output */
#define P8DIR               (PDDIR_H) /* Port 8 Direction */
#define P8REN               (PDREN_H) /* Port 8 Resistor Enable */
#define P8DS                (PDDS_H)  /* Port 8 Resistor Drive Strenght */
#define P8SEL               (PDSEL_H) /* Port 8 Selection */
                       
                   
/************************************************************
* DIGITAL I/O PortJ Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORTJ_R__        /* Definition to show that Module is available */

#define PJIN_                 0x0320    /* Port J Input */
const_sfrb(PJIN_L, PJIN_);
const_sfrb(PJIN_H, PJIN_+1);
const_sfrw(PJIN, PJIN_);
#define PJOUT_                0x0322    /* Port J Output */
sfrb(PJOUT_L, PJOUT_);
sfrb(PJOUT_H, PJOUT_+1);
sfrw(PJOUT, PJOUT_);
#define PJDIR_                0x0324    /* Port J Direction */
sfrb(PJDIR_L, PJDIR_);
sfrb(PJDIR_H, PJDIR_+1);
sfrw(PJDIR, PJDIR_);
#define PJREN_                0x0326    /* Port J Resistor Enable */
sfrb(PJREN_L, PJREN_);
sfrb(PJREN_H, PJREN_+1);
sfrw(PJREN, PJREN_);
#define PJDS_                 0x0328    /* Port J Resistor Drive Strenght */
sfrb(PJDS_L, PJDS_);
sfrb(PJDS_H, PJDS_+1);
sfrw(PJDS, PJDS_);



/************************************************************
* PORT MAPPING CONTROLLER
************************************************************/
#define __MSP430_HAS_PORT_MAPPING__   /* Definition to show that Module is available */

#define PMAPKEYID_	0x01C0    /* Port Mapping Key register */
sfrb(PMAPKEYID_L, PMAPKEYID_);
sfrb(PMAPKEYID_H, PMAPKEYID_+1);
sfrw(PMAPKEYID, PMAPKEYID_);
#define PMAPCTL_	0x01C2    /* Port Mapping control register */
sfrb(PMAPCTL_L, PMAPCTL_);
sfrb(PMAPCTL_H, PMAPCTL_+1);
sfrw(PMAPCTL, PMAPCTL_);

#define  PMAPKEY	0x2D52  /* Port Mapping Key */
#define  PMAPPWD	PMAPKEYID /* Legacy Definition: Mapping Key register */
#define  PMAPPW		0x2D52  /* Legacy Definition: Port Mapping Password */

/* PMAPCTL Control Bits */
#define PMAPLOCKED	0x0001  /* Port Mapping Lock bit. Read only */
#define PMAPRECFG	0x0002  /* Port Mapping re-configuration control bit */

/* PMAPCTL Control Bits */
#define PMAPLOCKED_L	0x0001  /* Port Mapping Lock bit. Read only */
#define PMAPRECFG_L	0x0002  /* Port Mapping re-configuration control bit */

/* PMAPCTL Control Bits */

/************************************************************
* PORT 4 MAPPING CONTROLLER
************************************************************/
#define __MSP430_HAS_PORT4_MAPPING__   /* Definition to show that Module is available */

#define P4MAP01_              0x01E0    /* Port P4.0/1 mapping register */
sfrb(P4MAP01_L, P4MAP01_);
sfrb(P4MAP01_H, P4MAP01_+1);
sfrw(P4MAP01, P4MAP01_);
#define P4MAP23_              0x01E2    /* Port P4.2/3 mapping register */
sfrb(P4MAP23_L, P4MAP23_);
sfrb(P4MAP23_H, P4MAP23_+1);
sfrw(P4MAP23, P4MAP23_);
#define P4MAP45_              0x01E4    /* Port P4.4/5 mapping register */
sfrb(P4MAP45_L, P4MAP45_);
sfrb(P4MAP45_H, P4MAP45_+1);
sfrw(P4MAP45, P4MAP45_);
#define P4MAP67_              0x01E6    /* Port P4.6/7 mapping register */
sfrb(P4MAP67_L, P4MAP67_);
sfrb(P4MAP67_H, P4MAP67_+1);
sfrw(P4MAP67, P4MAP67_);

#define  P4MAP0              P4MAP01_L /* Port P4.0 mapping register */
#define  P4MAP1              P4MAP01_H /* Port P4.1 mapping register */
#define  P4MAP2              P4MAP23_L /* Port P4.2 mapping register */
#define  P4MAP3              P4MAP23_H /* Port P4.3 mapping register */
#define  P4MAP4              P4MAP45_L /* Port P4.4 mapping register */
#define  P4MAP5              P4MAP45_H /* Port P4.5 mapping register */
#define  P4MAP6              P4MAP67_L /* Port P4.6 mapping register */
#define  P4MAP7              P4MAP67_H /* Port P4.7 mapping register */



#define PM_NONE       0
#define PM_CBOUT0     1
#define PM_TB0CLK     1
#define PM_ADC12CLK   2
#define PM_DMAE0      2
#define PM_SVMOUT     3
#define PM_TB0OUTH    3
#define PM_TB0CCR0A   4
#define PM_TB0CCR1A   5
#define PM_TB0CCR2A   6
#define PM_TB0CCR3A   7
#define PM_TB0CCR4A   8
#define PM_TB0CCR5A   9
#define PM_TB0CCR6A   10
#define PM_UCA1RXD    11
#define PM_UCA1SOMI   11
#define PM_UCA1TXD    12
#define PM_UCA1SIMO   12
#define PM_UCA1CLK    13
#define PM_UCB1STE    13
#define PM_UCB1SOMI   14
#define PM_UCB1SCL    14
#define PM_UCB1SIMO   15
#define PM_UCB1SDA    15
#define PM_UCB1CLK    16
#define PM_UCA1STE    16
#define PM_CBOUT1     17
#define PM_MCLK       18
#define PM_ANALOG     31

/************************************************************
* PMM - Power Management System
************************************************************/
#define __MSP430_HAS_PMM__            /* Definition to show that Module is available */

#define PMMCTL0_              0x0120    /* PMM Control 0 */
sfrb(PMMCTL0_L, PMMCTL0_);
sfrb(PMMCTL0_H, PMMCTL0_+1);
sfrw(PMMCTL0, PMMCTL0_);
#define PMMCTL1_              0x0122    /* PMM Control 1 */
sfrb(PMMCTL1_L, PMMCTL1_);
sfrb(PMMCTL1_H, PMMCTL1_+1);
sfrw(PMMCTL1, PMMCTL1_);
#define SVSMHCTL_             0x0124    /* SVS and SVM high side control register */
sfrb(SVSMHCTL_L, SVSMHCTL_);
sfrb(SVSMHCTL_H, SVSMHCTL_+1);
sfrw(SVSMHCTL, SVSMHCTL_);
#define SVSMLCTL_             0x0126    /* SVS and SVM low side control register */
sfrb(SVSMLCTL_L, SVSMLCTL_);
sfrb(SVSMLCTL_H, SVSMLCTL_+1);
sfrw(SVSMLCTL, SVSMLCTL_);
#define SVSMIO_               0x0128    /* SVSIN and SVSOUT control register */
sfrb(SVSMIO_L, SVSMIO_);
sfrb(SVSMIO_H, SVSMIO_+1);
sfrw(SVSMIO, SVSMIO_);
#define PMMIFG_               0x012C    /* PMM Interrupt Flag */
sfrb(PMMIFG_L, PMMIFG_);
sfrb(PMMIFG_H, PMMIFG_+1);
sfrw(PMMIFG, PMMIFG_);
#define PMMRIE_               0x012E    /* PMM and RESET Interrupt Enable */
sfrb(PMMRIE_L, PMMRIE_);
sfrb(PMMRIE_H, PMMRIE_+1);
sfrw(PMMRIE, PMMRIE_);
#define PM5CTL0_              0x0130    /* PMM Power Mode 5 Control Register 0 */
sfrb(PM5CTL0_L, PM5CTL0_);
sfrb(PM5CTL0_H, PM5CTL0_+1);
sfrw(PM5CTL0, PM5CTL0_);

#define PMMPW               (0xA500)  /* PMM Register Write Password */
#define PMMPW_H             (0xA5)    /* PMM Register Write Password for high word access */

/* PMMCTL0 Control Bits */
#define PMMCOREV0           (0x0001)  /* PMM Core Voltage Bit: 0 */
#define PMMCOREV1           (0x0002)  /* PMM Core Voltage Bit: 1 */
#define PMMSWBOR            (0x0004)  /* PMM Software BOR */
#define PMMSWPOR            (0x0008)  /* PMM Software POR */
#define PMMREGOFF           (0x0010)  /* PMM Turn Regulator off */
#define PMMHPMRE            (0x0080)  /* PMM Global High Power Module Request Enable */

/* PMMCTL0 Control Bits */
#define PMMCOREV0_L         (0x0001)  /* PMM Core Voltage Bit: 0 */
#define PMMCOREV1_L         (0x0002)  /* PMM Core Voltage Bit: 1 */
#define PMMSWBOR_L          (0x0004)  /* PMM Software BOR */
#define PMMSWPOR_L          (0x0008)  /* PMM Software POR */
#define PMMREGOFF_L         (0x0010)  /* PMM Turn Regulator off */
#define PMMHPMRE_L          (0x0080)  /* PMM Global High Power Module Request Enable */

/* PMMCTL0 Control Bits */

#define PMMCOREV_0          (0x0000)  /* PMM Core Voltage 0 (1.35V) */
#define PMMCOREV_1          (0x0001)  /* PMM Core Voltage 1 (1.55V) */
#define PMMCOREV_2          (0x0002)  /* PMM Core Voltage 2 (1.75V) */
#define PMMCOREV_3          (0x0003)  /* PMM Core Voltage 3 (1.85V) */


/* PMMCTL1 Control Bits */
#define PMMREFMD            (0x0001)  /* PMM Reference Mode */
#define PMMCMD0             (0x0010)  /* PMM Voltage Regulator Current Mode Bit: 0 */
#define PMMCMD1             (0x0020)  /* PMM Voltage Regulator Current Mode Bit: 1 */

/* PMMCTL1 Control Bits */
#define PMMREFMD_L          (0x0001)  /* PMM Reference Mode */
#define PMMCMD0_L           (0x0010)  /* PMM Voltage Regulator Current Mode Bit: 0 */
#define PMMCMD1_L           (0x0020)  /* PMM Voltage Regulator Current Mode Bit: 1 */

/* PMMCTL1 Control Bits */

/* SVSMHCTL Control Bits */
#define SVSMHRRL0           (0x0001)  /* SVS and SVM high side Reset Release Voltage Level Bit: 0 */
#define SVSMHRRL1           (0x0002)  /* SVS and SVM high side Reset Release Voltage Level Bit: 1 */
#define SVSMHRRL2           (0x0004)  /* SVS and SVM high side Reset Release Voltage Level Bit: 2 */
#define SVSMHDLYST          (0x0008)  /* SVS and SVM high side delay status */
#define SVSHMD              (0x0010)  /* SVS high side mode */
#define SVSMHEVM            (0x0040)  /* SVS and SVM high side event mask */
#define SVSMHACE            (0x0080)  /* SVS and SVM high side auto control enable */
#define SVSHRVL0            (0x0100)  /* SVS high side reset voltage level Bit: 0 */
#define SVSHRVL1            (0x0200)  /* SVS high side reset voltage level Bit: 1 */
#define SVSHE               (0x0400)  /* SVS high side enable */
#define SVSHFP              (0x0800)  /* SVS high side full performace mode */
#define SVMHOVPE            (0x1000)  /* SVM high side over-voltage enable */
#define SVMHE               (0x4000)  /* SVM high side enable */
#define SVMHFP              (0x8000)  /* SVM high side full performace mode */

/* SVSMHCTL Control Bits */
#define SVSMHRRL0_L         (0x0001)  /* SVS and SVM high side Reset Release Voltage Level Bit: 0 */
#define SVSMHRRL1_L         (0x0002)  /* SVS and SVM high side Reset Release Voltage Level Bit: 1 */
#define SVSMHRRL2_L         (0x0004)  /* SVS and SVM high side Reset Release Voltage Level Bit: 2 */
#define SVSMHDLYST_L        (0x0008)  /* SVS and SVM high side delay status */
#define SVSHMD_L            (0x0010)  /* SVS high side mode */
#define SVSMHEVM_L          (0x0040)  /* SVS and SVM high side event mask */
#define SVSMHACE_L          (0x0080)  /* SVS and SVM high side auto control enable */

/* SVSMHCTL Control Bits */
#define SVSHRVL0_H          (0x0001)  /* SVS high side reset voltage level Bit: 0 */
#define SVSHRVL1_H          (0x0002)  /* SVS high side reset voltage level Bit: 1 */
#define SVSHE_H             (0x0004)  /* SVS high side enable */
#define SVSHFP_H            (0x0008)  /* SVS high side full performace mode */
#define SVMHOVPE_H          (0x0010)  /* SVM high side over-voltage enable */
#define SVMHE_H             (0x0040)  /* SVM high side enable */
#define SVMHFP_H            (0x0080)  /* SVM high side full performace mode */

#define SVSMHRRL_0          (0x0000)  /* SVS and SVM high side Reset Release Voltage Level 0 */
#define SVSMHRRL_1          (0x0001)  /* SVS and SVM high side Reset Release Voltage Level 1 */
#define SVSMHRRL_2          (0x0002)  /* SVS and SVM high side Reset Release Voltage Level 2 */
#define SVSMHRRL_3          (0x0003)  /* SVS and SVM high side Reset Release Voltage Level 3 */
#define SVSMHRRL_4          (0x0004)  /* SVS and SVM high side Reset Release Voltage Level 4 */
#define SVSMHRRL_5          (0x0005)  /* SVS and SVM high side Reset Release Voltage Level 5 */
#define SVSMHRRL_6          (0x0006)  /* SVS and SVM high side Reset Release Voltage Level 6 */
#define SVSMHRRL_7          (0x0007)  /* SVS and SVM high side Reset Release Voltage Level 7 */

#define SVSHRVL_0           (0x0000)  /* SVS high side Reset Release Voltage Level 0 */
#define SVSHRVL_1           (0x0100)  /* SVS high side Reset Release Voltage Level 1 */
#define SVSHRVL_2           (0x0200)  /* SVS high side Reset Release Voltage Level 2 */
#define SVSHRVL_3           (0x0300)  /* SVS high side Reset Release Voltage Level 3 */


/* SVSMLCTL Control Bits */
#define SVSMLRRL0           (0x0001)  /* SVS and SVM low side Reset Release Voltage Level Bit: 0 */
#define SVSMLRRL1           (0x0002)  /* SVS and SVM low side Reset Release Voltage Level Bit: 1 */
#define SVSMLRRL2           (0x0004)  /* SVS and SVM low side Reset Release Voltage Level Bit: 2 */
#define SVSMLDLYST          (0x0008)  /* SVS and SVM low side delay status */
#define SVSLMD              (0x0010)  /* SVS low side mode */
#define SVSMLEVM            (0x0040)  /* SVS and SVM low side event mask */
#define SVSMLACE            (0x0080)  /* SVS and SVM low side auto control enable */
#define SVSLRVL0            (0x0100)  /* SVS low side reset voltage level Bit: 0 */
#define SVSLRVL1            (0x0200)  /* SVS low side reset voltage level Bit: 1 */
#define SVSLE               (0x0400)  /* SVS low side enable */
#define SVSLFP              (0x0800)  /* SVS low side full performace mode */
#define SVMLOVPE            (0x1000)  /* SVM low side over-voltage enable */
#define SVMLE               (0x4000)  /* SVM low side enable */
#define SVMLFP              (0x8000)  /* SVM low side full performace mode */

/* SVSMLCTL Control Bits */
#define SVSMLRRL0_L         (0x0001)  /* SVS and SVM low side Reset Release Voltage Level Bit: 0 */
#define SVSMLRRL1_L         (0x0002)  /* SVS and SVM low side Reset Release Voltage Level Bit: 1 */
#define SVSMLRRL2_L         (0x0004)  /* SVS and SVM low side Reset Release Voltage Level Bit: 2 */
#define SVSMLDLYST_L        (0x0008)  /* SVS and SVM low side delay status */
#define SVSLMD_L            (0x0010)  /* SVS low side mode */
#define SVSMLEVM_L          (0x0040)  /* SVS and SVM low side event mask */
#define SVSMLACE_L          (0x0080)  /* SVS and SVM low side auto control enable */

/* SVSMLCTL Control Bits */
#define SVSLRVL0_H          (0x0001)  /* SVS low side reset voltage level Bit: 0 */
#define SVSLRVL1_H          (0x0002)  /* SVS low side reset voltage level Bit: 1 */
#define SVSLE_H             (0x0004)  /* SVS low side enable */
#define SVSLFP_H            (0x0008)  /* SVS low side full performace mode */
#define SVMLOVPE_H          (0x0010)  /* SVM low side over-voltage enable */
#define SVMLE_H             (0x0040)  /* SVM low side enable */
#define SVMLFP_H            (0x0080)  /* SVM low side full performace mode */

#define SVSMLRRL_0          (0x0000)  /* SVS and SVM low side Reset Release Voltage Level 0 */
#define SVSMLRRL_1          (0x0001)  /* SVS and SVM low side Reset Release Voltage Level 1 */
#define SVSMLRRL_2          (0x0002)  /* SVS and SVM low side Reset Release Voltage Level 2 */
#define SVSMLRRL_3          (0x0003)  /* SVS and SVM low side Reset Release Voltage Level 3 */
#define SVSMLRRL_4          (0x0004)  /* SVS and SVM low side Reset Release Voltage Level 4 */
#define SVSMLRRL_5          (0x0005)  /* SVS and SVM low side Reset Release Voltage Level 5 */
#define SVSMLRRL_6          (0x0006)  /* SVS and SVM low side Reset Release Voltage Level 6 */
#define SVSMLRRL_7          (0x0007)  /* SVS and SVM low side Reset Release Voltage Level 7 */

#define SVSLRVL_0           (0x0000)  /* SVS low side Reset Release Voltage Level 0 */
#define SVSLRVL_1           (0x0100)  /* SVS low side Reset Release Voltage Level 1 */
#define SVSLRVL_2           (0x0200)  /* SVS low side Reset Release Voltage Level 2 */
#define SVSLRVL_3           (0x0300)  /* SVS low side Reset Release Voltage Level 3 */


/* SVSMIO Control Bits */
#define SVMLOE              (0x0008)  /* SVM low side output enable */
#define SVMLVLROE           (0x0010)  /* SVM low side voltage level reached output enable */
#define SVMOUTPOL           (0x0020)  /* SVMOUT pin polarity */
#define SVMHOE              (0x0800)  /* SVM high side output enable */
#define SVMHVLROE           (0x1000)  /* SVM high side voltage level reached output enable */

/* SVSMIO Control Bits */
#define SVMLOE_L            (0x0008)  /* SVM low side output enable */
#define SVMLVLROE_L         (0x0010)  /* SVM low side voltage level reached output enable */
#define SVMOUTPOL_L         (0x0020)  /* SVMOUT pin polarity */

/* SVSMIO Control Bits */
#define SVMHOE_H            (0x0008)  /* SVM high side output enable */
#define SVMHVLROE_H         (0x0010)  /* SVM high side voltage level reached output enable */


/* PMMIFG Control Bits */
#define SVSMLDLYIFG         (0x0001)  /* SVS and SVM low side Delay expired interrupt flag */
#define SVMLIFG             (0x0002)  /* SVM low side interrupt flag */
#define SVMLVLRIFG          (0x0004)  /* SVM low side Voltage Level Reached interrupt flag */
#define SVSMHDLYIFG         (0x0010)  /* SVS and SVM high side Delay expired interrupt flag */
#define SVMHIFG             (0x0020)  /* SVM high side interrupt flag */
#define SVMHVLRIFG          (0x0040)  /* SVM high side Voltage Level Reached interrupt flag */
#define PMMBORIFG           (0x0100)  /* PMM Software BOR interrupt flag */
#define PMMRSTIFG           (0x0200)  /* PMM RESET pin interrupt flag */
#define PMMPORIFG           (0x0400)  /* PMM Software POR interrupt flag */
#define SVSHIFG             (0x1000)  /* SVS low side interrupt flag */
#define SVSLIFG             (0x2000)  /* SVS high side interrupt flag */
#define PMMLPM5IFG          (0x8000)  /* LPM5 indication Flag */

/* PMMIFG Control Bits */
#define SVSMLDLYIFG_L       (0x0001)  /* SVS and SVM low side Delay expired interrupt flag */
#define SVMLIFG_L           (0x0002)  /* SVM low side interrupt flag */
#define SVMLVLRIFG_L        (0x0004)  /* SVM low side Voltage Level Reached interrupt flag */
#define SVSMHDLYIFG_L       (0x0010)  /* SVS and SVM high side Delay expired interrupt flag */
#define SVMHIFG_L           (0x0020)  /* SVM high side interrupt flag */
#define SVMHVLRIFG_L        (0x0040)  /* SVM high side Voltage Level Reached interrupt flag */

/* PMMIFG Control Bits */
#define PMMBORIFG_H         (0x0001)  /* PMM Software BOR interrupt flag */
#define PMMRSTIFG_H         (0x0002)  /* PMM RESET pin interrupt flag */
#define PMMPORIFG_H         (0x0004)  /* PMM Software POR interrupt flag */
#define SVSHIFG_H           (0x0010)  /* SVS low side interrupt flag */
#define SVSLIFG_H           (0x0020)  /* SVS high side interrupt flag */
#define PMMLPM5IFG_H        (0x0080)  /* LPM5 indication Flag */

#define PMMRSTLPM5IFG       PMMLPM5IFG /* LPM5 indication Flag */


/* PMMIE and RESET Control Bits */
#define SVSMLDLYIE          (0x0001)  /* SVS and SVM low side Delay expired interrupt enable */
#define SVMLIE              (0x0002)  /* SVM low side interrupt enable */
#define SVMLVLRIE           (0x0004)  /* SVM low side Voltage Level Reached interrupt enable */
#define SVSMHDLYIE          (0x0010)  /* SVS and SVM high side Delay expired interrupt enable */
#define SVMHIE              (0x0020)  /* SVM high side interrupt enable */
#define SVMHVLRIE           (0x0040)  /* SVM high side Voltage Level Reached interrupt enable */
#define SVSLPE              (0x0100)  /* SVS low side POR enable */
#define SVMLVLRPE           (0x0200)  /* SVM low side Voltage Level reached POR enable */
#define SVSHPE              (0x1000)  /* SVS high side POR enable */
#define SVMHVLRPE           (0x2000)  /* SVM high side Voltage Level reached POR enable */

/* PMMIE and RESET Control Bits */
#define SVSMLDLYIE_L        (0x0001)  /* SVS and SVM low side Delay expired interrupt enable */
#define SVMLIE_L            (0x0002)  /* SVM low side interrupt enable */
#define SVMLVLRIE_L         (0x0004)  /* SVM low side Voltage Level Reached interrupt enable */
#define SVSMHDLYIE_L        (0x0010)  /* SVS and SVM high side Delay expired interrupt enable */
#define SVMHIE_L            (0x0020)  /* SVM high side interrupt enable */
#define SVMHVLRIE_L         (0x0040)  /* SVM high side Voltage Level Reached interrupt enable */

/* PMMIE and RESET Control Bits */
#define SVSLPE_H            (0x0001)  /* SVS low side POR enable */
#define SVMLVLRPE_H         (0x0002)  /* SVM low side Voltage Level reached POR enable */
#define SVSHPE_H            (0x0010)  /* SVS high side POR enable */
#define SVMHVLRPE_H         (0x0020)  /* SVM high side Voltage Level reached POR enable */

/* PM5CTL0 Power Mode 5 Control Bits */
#define LOCKLPM5            (0x0001)  /* Lock I/O pin configuration upon entry/exit to/from LPM5 */

/* PM5CTL0 Power Mode 5 Control Bits */
#define LOCKLPM5_L          (0x0001)  /* Lock I/O pin configuration upon entry/exit to/from LPM5 */

/* PM5CTL0 Power Mode 5 Control Bits */
#define LOCKIO              LOCKLPM5  /* Lock I/O pin configuration upon entry/exit to/from LPM5 */

/*************************************************************
* RAM Control Module
*************************************************************/
#define __MSP430_HAS_RC__             /* Definition to show that Module is available */

#define RCCTL0_               0x0158    /* Ram Controller Control Register */
sfrb(RCCTL0_L, RCCTL0_);
sfrb(RCCTL0_H, RCCTL0_+1);
sfrw(RCCTL0, RCCTL0_);

/* RCCTL0 Control Bits */
#define RCRS0OFF            (0x0001)  /* RAM Controller RAM Sector 0 Off */
#define RCRS1OFF            (0x0002)  /* RAM Controller RAM Sector 1 Off */
#define RCRS2OFF            (0x0004)  /* RAM Controller RAM Sector 2 Off */
#define RCRS3OFF            (0x0008)  /* RAM Controller RAM Sector 3 Off */
#define RCRS7OFF            (0x0080)  /* RAM Controller RAM Sector 7 (USB) Off */

/* RCCTL0 Control Bits */
#define RCRS0OFF_L          (0x0001)  /* RAM Controller RAM Sector 0 Off */
#define RCRS1OFF_L          (0x0002)  /* RAM Controller RAM Sector 1 Off */
#define RCRS2OFF_L          (0x0004)  /* RAM Controller RAM Sector 2 Off */
#define RCRS3OFF_L          (0x0008)  /* RAM Controller RAM Sector 3 Off */
#define RCRS7OFF_L          (0x0080)  /* RAM Controller RAM Sector 7 (USB) Off */

/* RCCTL0 Control Bits */

#define RCKEY               (0x5A00)

/************************************************************
* Shared Reference
************************************************************/
#define __MSP430_HAS_REF__          /* Definition to show that Module is available */

#define REFCTL0_              0x01B0    /* REF Shared Reference control register 0 */
sfrb(REFCTL0_L, REFCTL0_);
sfrb(REFCTL0_H, REFCTL0_+1);
sfrw(REFCTL0, REFCTL0_);

/* REFCTL0 Control Bits */
#define REFON               (0x0001)  /* REF Reference On */
#define REFOUT              (0x0002)  /* REF Reference output Buffer On */
//#define RESERVED            (0x0004)  /* Reserved */
#define REFTCOFF            (0x0008)  /* REF Temp.Sensor off */
#define REFVSEL0            (0x0010)  /* REF Reference Voltage Level Select Bit:0 */
#define REFVSEL1            (0x0020)  /* REF Reference Voltage Level Select Bit:1 */
//#define RESERVED            (0x0040)  /* Reserved */
#define REFMSTR             (0x0080)  /* REF Master Control */
#define REFGENACT           (0x0100)  /* REF Reference generator active */
#define REFBGACT            (0x0200)  /* REF Reference bandgap active */
#define REFGENBUSY          (0x0400)  /* REF Reference generator busy */
#define BGMODE              (0x0800)  /* REF Bandgap mode */
//#define RESERVED            (0x1000)  /* Reserved */
//#define RESERVED            (0x2000)  /* Reserved */
//#define RESERVED            (0x4000)  /* Reserved */
//#define RESERVED            (0x8000)  /* Reserved */

/* REFCTL0 Control Bits */
#define REFON_L             (0x0001)  /* REF Reference On */
#define REFOUT_L            (0x0002)  /* REF Reference output Buffer On */
//#define RESERVED            (0x0004)  /* Reserved */
#define REFTCOFF_L          (0x0008)  /* REF Temp.Sensor off */
#define REFVSEL0_L          (0x0010)  /* REF Reference Voltage Level Select Bit:0 */
#define REFVSEL1_L          (0x0020)  /* REF Reference Voltage Level Select Bit:1 */
//#define RESERVED            (0x0040)  /* Reserved */
#define REFMSTR_L           (0x0080)  /* REF Master Control */
//#define RESERVED            (0x1000)  /* Reserved */
//#define RESERVED            (0x2000)  /* Reserved */
//#define RESERVED            (0x4000)  /* Reserved */
//#define RESERVED            (0x8000)  /* Reserved */

/* REFCTL0 Control Bits */
//#define RESERVED            (0x0004)  /* Reserved */
//#define RESERVED            (0x0040)  /* Reserved */
#define REFGENACT_H         (0x0001)  /* REF Reference generator active */
#define REFBGACT_H          (0x0002)  /* REF Reference bandgap active */
#define REFGENBUSY_H        (0x0004)  /* REF Reference generator busy */
#define BGMODE_H            (0x0008)  /* REF Bandgap mode */
//#define RESERVED            (0x1000)  /* Reserved */
//#define RESERVED            (0x2000)  /* Reserved */
//#define RESERVED            (0x4000)  /* Reserved */
//#define RESERVED            (0x8000)  /* Reserved */

#define REFVSEL_0           (0x0000)  /* REF Reference Voltage Level Select 1.5V */
#define REFVSEL_1           (0x0010)  /* REF Reference Voltage Level Select 2.0V */
#define REFVSEL_2           (0x0020)  /* REF Reference Voltage Level Select 2.5V */
#define REFVSEL_3           (0x0030)  /* REF Reference Voltage Level Select 2.5V */

/************************************************************
* Real Time Clock
************************************************************/
#define __MSP430_HAS_RTC__            /* Definition to show that Module is available */

#define RTCCTL01_             0x04A0    /* Real Timer Control 0/1 */
sfrb(RTCCTL01_L, RTCCTL01_);
sfrb(RTCCTL01_H, RTCCTL01_+1);
sfrw(RTCCTL01, RTCCTL01_);
#define RTCCTL23_             0x04A2    /* Real Timer Control 2/3 */
sfrb(RTCCTL23_L, RTCCTL23_);
sfrb(RTCCTL23_H, RTCCTL23_+1);
sfrw(RTCCTL23, RTCCTL23_);
#define RTCPS0CTL_            0x04A8    /* Real Timer Prescale Timer 0 Control */
sfrb(RTCPS0CTL_L, RTCPS0CTL_);
sfrb(RTCPS0CTL_H, RTCPS0CTL_+1);
sfrw(RTCPS0CTL, RTCPS0CTL_);
#define RTCPS1CTL_            0x04AA    /* Real Timer Prescale Timer 1 Control */
sfrb(RTCPS1CTL_L, RTCPS1CTL_);
sfrb(RTCPS1CTL_H, RTCPS1CTL_+1);
sfrw(RTCPS1CTL, RTCPS1CTL_);
#define RTCPS_                0x04AC    /* Real Timer Prescale Timer Control */
sfrb(RTCPS_L, RTCPS_);
sfrb(RTCPS_H, RTCPS_+1);
sfrw(RTCPS, RTCPS_);
#define RTCIV_                0x04AE    /* Real Time Clock Interrupt Vector */
sfrw(RTCIV, RTCIV_);
#define RTCTIM0_              0x04B0    /* Real Time Clock Time 0 */
sfrb(RTCTIM0_L, RTCTIM0_);
sfrb(RTCTIM0_H, RTCTIM0_+1);
sfrw(RTCTIM0, RTCTIM0_);
#define RTCTIM1_              0x04B2    /* Real Time Clock Time 1 */
sfrb(RTCTIM1_L, RTCTIM1_);
sfrb(RTCTIM1_H, RTCTIM1_+1);
sfrw(RTCTIM1, RTCTIM1_);
#define RTCDATE_              0x04B4    /* Real Time Clock Date */
sfrb(RTCDATE_L, RTCDATE_);
sfrb(RTCDATE_H, RTCDATE_+1);
sfrw(RTCDATE, RTCDATE_);
#define RTCYEAR_              0x04B6    /* Real Time Clock Year */
sfrb(RTCYEAR_L, RTCYEAR_);
sfrb(RTCYEAR_H, RTCYEAR_+1);
sfrw(RTCYEAR, RTCYEAR_);
#define RTCAMINHR_            0x04B8    /* Real Time Clock Alarm Min/Hour */
sfrb(RTCAMINHR_L, RTCAMINHR_);
sfrb(RTCAMINHR_H, RTCAMINHR_+1);
sfrw(RTCAMINHR, RTCAMINHR_);
#define RTCADOWDAY_           0x04BA    /* Real Time Clock Alarm day of week/day */
sfrb(RTCADOWDAY_L, RTCADOWDAY_);
sfrb(RTCADOWDAY_H, RTCADOWDAY_+1);
sfrw(RTCADOWDAY, RTCADOWDAY_);

#define RTCCTL0             RTCCTL01_L  /* Real Time Clock Control 0 */
#define RTCCTL1             RTCCTL01_H  /* Real Time Clock Control 1 */
#define RTCCTL2             RTCCTL23_L  /* Real Time Clock Control 2 */
#define RTCCTL3             RTCCTL23_H  /* Real Time Clock Control 3 */
#define RTCNT12             RTCTIM0
#define RTCNT34             RTCTIM1
#define RTCNT1              RTCTIM0_L
#define RTCNT2              RTCTIM0_H
#define RTCNT3              RTCTIM1_L
#define RTCNT4              RTCTIM1_H
#define RTCSEC              RTCTIM0_L
#define RTCMIN              RTCTIM0_H
#define RTCHOUR             RTCTIM1_L
#define RTCDOW              RTCTIM1_H
#define RTCDAY              RTCDATE_L
#define RTCMON              RTCDATE_H
#define RTCYEARL            RTCYEAR_L
#define RTCYEARH            RTCYEAR_H
#define RT0PS               RTCPS_L
#define RT1PS               RTCPS_H
#define RTCAMIN             RTCAMINHR_L  /* Real Time Clock Alarm Min */
#define RTCAHOUR            RTCAMINHR_H  /* Real Time Clock Alarm Hour */
#define RTCADOW             RTCADOWDAY_L /* Real Time Clock Alarm day of week */
#define RTCADAY             RTCADOWDAY_H /* Real Time Clock Alarm day */

/* RTCCTL01 Control Bits */
#define RTCBCD              (0x8000)                   /* RTC BCD  0:Binary / 1:BCD */
#define RTCHOLD             (0x4000)                   /* RTC Hold */
#define RTCMODE             (0x2000)                   /* RTC Mode 0:Counter / 1: Calendar */
#define RTCRDY              (0x1000)                   /* RTC Ready */
#define RTCSSEL1            (0x0800)                   /* RTC Source Select 1 */
#define RTCSSEL0            (0x0400)                   /* RTC Source Select 0 */
#define RTCTEV1             (0x0200)                   /* RTC Time Event 1 */
#define RTCTEV0             (0x0100)                   /* RTC Time Event 0 */
//#define Reserved          (0x0080)
#define RTCTEVIE            (0x0040)                   /* RTC Time Event Interrupt Enable Flag */
#define RTCAIE              (0x0020)                   /* RTC Alarm Interrupt Enable Flag */
#define RTCRDYIE            (0x0010)                   /* RTC Ready Interrupt Enable Flag */
//#define Reserved          (0x0008)
#define RTCTEVIFG           (0x0004)                   /* RTC Time Event Interrupt Flag */
#define RTCAIFG             (0x0002)                   /* RTC Alarm Interrupt Flag */
#define RTCRDYIFG           (0x0001)                   /* RTC Ready Interrupt Flag */

/* RTCCTL01 Control Bits */
//#define Reserved          (0x0080)
#define RTCTEVIE_L          (0x0040)                   /* RTC Time Event Interrupt Enable Flag */
#define RTCAIE_L            (0x0020)                   /* RTC Alarm Interrupt Enable Flag */
#define RTCRDYIE_L          (0x0010)                   /* RTC Ready Interrupt Enable Flag */
//#define Reserved          (0x0008)
#define RTCTEVIFG_L         (0x0004)                   /* RTC Time Event Interrupt Flag */
#define RTCAIFG_L           (0x0002)                   /* RTC Alarm Interrupt Flag */
#define RTCRDYIFG_L         (0x0001)                   /* RTC Ready Interrupt Flag */

/* RTCCTL01 Control Bits */
#define RTCBCD_H            (0x0080)                   /* RTC BCD  0:Binary / 1:BCD */
#define RTCHOLD_H           (0x0040)                   /* RTC Hold */
#define RTCMODE_H           (0x0020)                   /* RTC Mode 0:Counter / 1: Calendar */
#define RTCRDY_H            (0x0010)                   /* RTC Ready */
#define RTCSSEL1_H          (0x0008)                   /* RTC Source Select 1 */
#define RTCSSEL0_H          (0x0004)                   /* RTC Source Select 0 */
#define RTCTEV1_H           (0x0002)                   /* RTC Time Event 1 */
#define RTCTEV0_H           (0x0001)                   /* RTC Time Event 0 */
//#define Reserved          (0x0080)
//#define Reserved          (0x0008)

#define RTCSSEL_0           (0x0000)                   /* RTC Source Select ACLK */
#define RTCSSEL_1           (0x0400)                   /* RTC Source Select SMCLK */
#define RTCSSEL_2           (0x0800)                   /* RTC Source Select RT1PS */
#define RTCSSEL_3           (0x0C00)                   /* RTC Source Select RT1PS */
#define RTCSSEL__ACLK       (0x0000)                   /* RTC Source Select ACLK */
#define RTCSSEL__SMCLK      (0x0400)                   /* RTC Source Select SMCLK */
#define RTCSSEL__RT1PS      (0x0800)                   /* RTC Source Select RT1PS */
#define RTCTEV_0            (0x0000)                   /* RTC Time Event: 0 (Min. changed) */
#define RTCTEV_1            (0x0100)                   /* RTC Time Event: 1 (Hour changed) */
#define RTCTEV_2            (0x0200)                   /* RTC Time Event: 2 (12:00 changed) */
#define RTCTEV_3            (0x0300)                   /* RTC Time Event: 3 (00:00 changed) */
#define RTCTEV__MIN         (0x0000)                   /* RTC Time Event: 0 (Min. changed) */
#define RTCTEV__HOUR        (0x0100)                   /* RTC Time Event: 1 (Hour changed) */
#define RTCTEV__1200        (0x0200)                   /* RTC Time Event: 2 (12:00 changed) */
#define RTCTEV__0000        (0x0300)                   /* RTC Time Event: 3 (00:00 changed) */

/* RTCCTL23 Control Bits */
#define RTCCALF1            (0x0200)                   /* RTC Calibration Frequency Bit 1 */
#define RTCCALF0            (0x0100)                   /* RTC Calibration Frequency Bit 0 */
#define RTCCALS             (0x0080)                   /* RTC Calibration Sign */
//#define Reserved          (0x0040)
#define RTCCAL5             (0x0020)                   /* RTC Calibration Bit 5 */
#define RTCCAL4             (0x0010)                   /* RTC Calibration Bit 4 */
#define RTCCAL3             (0x0008)                   /* RTC Calibration Bit 3 */
#define RTCCAL2             (0x0004)                   /* RTC Calibration Bit 2 */
#define RTCCAL1             (0x0002)                   /* RTC Calibration Bit 1 */
#define RTCCAL0             (0x0001)                   /* RTC Calibration Bit 0 */

/* RTCCTL23 Control Bits */
#define RTCCALS_L           (0x0080)                   /* RTC Calibration Sign */
//#define Reserved          (0x0040)
#define RTCCAL5_L           (0x0020)                   /* RTC Calibration Bit 5 */
#define RTCCAL4_L           (0x0010)                   /* RTC Calibration Bit 4 */
#define RTCCAL3_L           (0x0008)                   /* RTC Calibration Bit 3 */
#define RTCCAL2_L           (0x0004)                   /* RTC Calibration Bit 2 */
#define RTCCAL1_L           (0x0002)                   /* RTC Calibration Bit 1 */
#define RTCCAL0_L           (0x0001)                   /* RTC Calibration Bit 0 */

/* RTCCTL23 Control Bits */
#define RTCCALF1_H          (0x0002)                   /* RTC Calibration Frequency Bit 1 */
#define RTCCALF0_H          (0x0001)                   /* RTC Calibration Frequency Bit 0 */
//#define Reserved          (0x0040)

#define RTCCALF_0           (0x0000)                   /* RTC Calibration Frequency: No Output */
#define RTCCALF_1           (0x0100)                   /* RTC Calibration Frequency: 512 Hz */
#define RTCCALF_2           (0x0200)                   /* RTC Calibration Frequency: 256 Hz */
#define RTCCALF_3           (0x0300)                   /* RTC Calibration Frequency: 1 Hz */

/* RTCPS0CTL Control Bits */
//#define Reserved          (0x8000)
#define RT0SSEL             (0x4000)                   /* RTC Prescale Timer 0 Source Select 0:ACLK / 1:SMCLK */
#define RT0PSDIV2           (0x2000)                   /* RTC Prescale Timer 0 Clock Divide Bit: 2 */
#define RT0PSDIV1           (0x1000)                   /* RTC Prescale Timer 0 Clock Divide Bit: 1 */
#define RT0PSDIV0           (0x0800)                   /* RTC Prescale Timer 0 Clock Divide Bit: 0 */
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
#define RT0PSHOLD           (0x0100)                   /* RTC Prescale Timer 0 Hold */
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)
#define RT0IP2              (0x0010)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 2 */
#define RT0IP1              (0x0008)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 1 */
#define RT0IP0              (0x0004)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 0 */
#define RT0PSIE             (0x0002)                   /* RTC Prescale Timer 0 Interrupt Enable Flag */
#define RT0PSIFG            (0x0001)                   /* RTC Prescale Timer 0 Interrupt Flag */

/* RTCPS0CTL Control Bits */
//#define Reserved          (0x8000)
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)
#define RT0IP2_L            (0x0010)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 2 */
#define RT0IP1_L            (0x0008)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 1 */
#define RT0IP0_L            (0x0004)                   /* RTC Prescale Timer 0 Interrupt Interval Bit: 0 */
#define RT0PSIE_L           (0x0002)                   /* RTC Prescale Timer 0 Interrupt Enable Flag */
#define RT0PSIFG_L          (0x0001)                   /* RTC Prescale Timer 0 Interrupt Flag */

/* RTCPS0CTL Control Bits */
//#define Reserved          (0x8000)
#define RT0SSEL_H           (0x0040)                   /* RTC Prescale Timer 0 Source Select 0:ACLK / 1:SMCLK */
#define RT0PSDIV2_H         (0x0020)                   /* RTC Prescale Timer 0 Clock Divide Bit: 2 */
#define RT0PSDIV1_H         (0x0010)                   /* RTC Prescale Timer 0 Clock Divide Bit: 1 */
#define RT0PSDIV0_H         (0x0008)                   /* RTC Prescale Timer 0 Clock Divide Bit: 0 */
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
#define RT0PSHOLD_H         (0x0001)                   /* RTC Prescale Timer 0 Hold */
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)

#define RT0IP_0             (0x0000)                   /* RTC Prescale Timer 0 Interrupt Interval /2 */
#define RT0IP_1             (0x0004)                   /* RTC Prescale Timer 0 Interrupt Interval /4 */
#define RT0IP_2             (0x0008)                   /* RTC Prescale Timer 0 Interrupt Interval /8 */
#define RT0IP_3             (0x000C)                   /* RTC Prescale Timer 0 Interrupt Interval /16 */
#define RT0IP_4             (0x0010)                   /* RTC Prescale Timer 0 Interrupt Interval /32 */
#define RT0IP_5             (0x0014)                   /* RTC Prescale Timer 0 Interrupt Interval /64 */
#define RT0IP_6             (0x0018)                   /* RTC Prescale Timer 0 Interrupt Interval /128 */
#define RT0IP_7             (0x001C)                   /* RTC Prescale Timer 0 Interrupt Interval /256 */

#define RT0PSDIV_0          (0x0000)                   /* RTC Prescale Timer 0 Clock Divide /2 */
#define RT0PSDIV_1          (0x0800)                   /* RTC Prescale Timer 0 Clock Divide /4 */
#define RT0PSDIV_2          (0x1000)                   /* RTC Prescale Timer 0 Clock Divide /8 */
#define RT0PSDIV_3          (0x1800)                   /* RTC Prescale Timer 0 Clock Divide /16 */
#define RT0PSDIV_4          (0x2000)                   /* RTC Prescale Timer 0 Clock Divide /32 */
#define RT0PSDIV_5          (0x2800)                   /* RTC Prescale Timer 0 Clock Divide /64 */
#define RT0PSDIV_6          (0x3000)                   /* RTC Prescale Timer 0 Clock Divide /128 */
#define RT0PSDIV_7          (0x3800)                   /* RTC Prescale Timer 0 Clock Divide /256 */


/* RTCPS1CTL Control Bits */
#define RT1SSEL1            (0x8000)                   /* RTC Prescale Timer 1 Source Select Bit 1 */
#define RT1SSEL0            (0x4000)                   /* RTC Prescale Timer 1 Source Select Bit 0 */
#define RT1PSDIV2           (0x2000)                   /* RTC Prescale Timer 1 Clock Divide Bit: 2 */
#define RT1PSDIV1           (0x1000)                   /* RTC Prescale Timer 1 Clock Divide Bit: 1 */
#define RT1PSDIV0           (0x0800)                   /* RTC Prescale Timer 1 Clock Divide Bit: 0 */
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
#define RT1PSHOLD           (0x0100)                   /* RTC Prescale Timer 1 Hold */
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)
#define RT1IP2              (0x0010)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 2 */
#define RT1IP1              (0x0008)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 1 */
#define RT1IP0              (0x0004)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 0 */
#define RT1PSIE             (0x0002)                   /* RTC Prescale Timer 1 Interrupt Enable Flag */
#define RT1PSIFG            (0x0001)                   /* RTC Prescale Timer 1 Interrupt Flag */

/* RTCPS1CTL Control Bits */
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)
#define RT1IP2_L            (0x0010)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 2 */
#define RT1IP1_L            (0x0008)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 1 */
#define RT1IP0_L            (0x0004)                   /* RTC Prescale Timer 1 Interrupt Interval Bit: 0 */
#define RT1PSIE_L           (0x0002)                   /* RTC Prescale Timer 1 Interrupt Enable Flag */
#define RT1PSIFG_L          (0x0001)                   /* RTC Prescale Timer 1 Interrupt Flag */

/* RTCPS1CTL Control Bits */
#define RT1SSEL1_H          (0x0080)                   /* RTC Prescale Timer 1 Source Select Bit 1 */
#define RT1SSEL0_H          (0x0040)                   /* RTC Prescale Timer 1 Source Select Bit 0 */
#define RT1PSDIV2_H         (0x0020)                   /* RTC Prescale Timer 1 Clock Divide Bit: 2 */
#define RT1PSDIV1_H         (0x0010)                   /* RTC Prescale Timer 1 Clock Divide Bit: 1 */
#define RT1PSDIV0_H         (0x0008)                   /* RTC Prescale Timer 1 Clock Divide Bit: 0 */
//#define Reserved          (0x0400)
//#define Reserved          (0x0200)
#define RT1PSHOLD_H         (0x0001)                   /* RTC Prescale Timer 1 Hold */
//#define Reserved          (0x0080)
//#define Reserved          (0x0040)
//#define Reserved          (0x0020)

#define RT1IP_0             (0x0000)                   /* RTC Prescale Timer 1 Interrupt Interval /2 */
#define RT1IP_1             (0x0004)                   /* RTC Prescale Timer 1 Interrupt Interval /4 */
#define RT1IP_2             (0x0008)                   /* RTC Prescale Timer 1 Interrupt Interval /8 */
#define RT1IP_3             (0x000C)                   /* RTC Prescale Timer 1 Interrupt Interval /16 */
#define RT1IP_4             (0x0010)                   /* RTC Prescale Timer 1 Interrupt Interval /32 */
#define RT1IP_5             (0x0014)                   /* RTC Prescale Timer 1 Interrupt Interval /64 */
#define RT1IP_6             (0x0018)                   /* RTC Prescale Timer 1 Interrupt Interval /128 */
#define RT1IP_7             (0x001C)                   /* RTC Prescale Timer 1 Interrupt Interval /256 */

#define RT1PSDIV_0          (0x0000)                   /* RTC Prescale Timer 1 Clock Divide /2 */
#define RT1PSDIV_1          (0x0800)                   /* RTC Prescale Timer 1 Clock Divide /4 */
#define RT1PSDIV_2          (0x1000)                   /* RTC Prescale Timer 1 Clock Divide /8 */
#define RT1PSDIV_3          (0x1800)                   /* RTC Prescale Timer 1 Clock Divide /16 */
#define RT1PSDIV_4          (0x2000)                   /* RTC Prescale Timer 1 Clock Divide /32 */
#define RT1PSDIV_5          (0x2800)                   /* RTC Prescale Timer 1 Clock Divide /64 */
#define RT1PSDIV_6          (0x3000)                   /* RTC Prescale Timer 1 Clock Divide /128 */
#define RT1PSDIV_7          (0x3800)                   /* RTC Prescale Timer 1 Clock Divide /256 */

#define RT1SSEL_0           (0x0000)                   /* RTC Prescale Timer Source Select ACLK */
#define RT1SSEL_1           (0x4000)                   /* RTC Prescale Timer Source Select SMCLK */
#define RT1SSEL_2           (0x8000)                   /* RTC Prescale Timer Source Select RT0PS */
#define RT1SSEL_3           (0xC000)                   /* RTC Prescale Timer Source Select RT0PS */

/* RTC Definitions */
#define RTC_NONE           (0x0000)    /* No Interrupt pending */
#define RTC_RTCRDYIFG      (0x0002)    /* RTC ready: RTCRDYIFG */
#define RTC_RTCTEVIFG      (0x0004)    /* RTC interval timer: RTCTEVIFG */
#define RTC_RTCAIFG        (0x0006)    /* RTC user alarm: RTCAIFG */
#define RTC_RT0PSIFG       (0x0008)    /* RTC prescaler 0: RT0PSIFG */
#define RTC_RT1PSIFG       (0x000A)    /* RTC prescaler 1: RT1PSIFG */

/************************************************************
* SFR - Special Function Register Module
************************************************************/
#define __MSP430_HAS_SFR__            /* Definition to show that Module is available */

#define SFRIE1_               0x0100    /* Interrupt Enable 1 */
sfrb(SFRIE1_L, SFRIE1_);
sfrb(SFRIE1_H, SFRIE1_+1);
sfrw(SFRIE1, SFRIE1_);

/* SFRIE1 Control Bits */
#define WDTIE               (0x0001)  /* WDT Interrupt Enable */
#define OFIE                (0x0002)  /* Osc Fault Enable */
//#define Reserved          (0x0004)
#define VMAIE               (0x0008)  /* Vacant Memory Interrupt Enable */
#define NMIIE               (0x0010)  /* NMI Interrupt Enable */
#define ACCVIE              (0x0020)  /* Flash Access Violation Interrupt Enable */
#define JMBINIE             (0x0040)  /* JTAG Mail Box input Interrupt Enable */
#define JMBOUTIE            (0x0080)  /* JTAG Mail Box output Interrupt Enable */

#define WDTIE_L             (0x0001)  /* WDT Interrupt Enable */
#define OFIE_L              (0x0002)  /* Osc Fault Enable */
//#define Reserved          (0x0004)
#define VMAIE_L             (0x0008)  /* Vacant Memory Interrupt Enable */
#define NMIIE_L             (0x0010)  /* NMI Interrupt Enable */
#define ACCVIE_L            (0x0020)  /* Flash Access Violation Interrupt Enable */
#define JMBINIE_L           (0x0040)  /* JTAG Mail Box input Interrupt Enable */
#define JMBOUTIE_L          (0x0080)  /* JTAG Mail Box output Interrupt Enable */

//#define Reserved          (0x0004)

#define SFRIFG1_              0x0102    /* Interrupt Flag 1 */
sfrb(SFRIFG1_L, SFRIFG1_);
sfrb(SFRIFG1_H, SFRIFG1_+1);
sfrw(SFRIFG1, SFRIFG1_);
/* SFRIFG1 Control Bits */
#define WDTIFG              (0x0001)  /* WDT Interrupt Flag */
#define OFIFG               (0x0002)  /* Osc Fault Flag */
//#define Reserved          (0x0004)
#define VMAIFG              (0x0008)  /* Vacant Memory Interrupt Flag */
#define NMIIFG              (0x0010)  /* NMI Interrupt Flag */
//#define Reserved          (0x0020)
#define JMBINIFG            (0x0040)  /* JTAG Mail Box input Interrupt Flag */
#define JMBOUTIFG           (0x0080)  /* JTAG Mail Box output Interrupt Flag */

#define WDTIFG_L            (0x0001)  /* WDT Interrupt Flag */
#define OFIFG_L             (0x0002)  /* Osc Fault Flag */
//#define Reserved          (0x0004)
#define VMAIFG_L            (0x0008)  /* Vacant Memory Interrupt Flag */
#define NMIIFG_L            (0x0010)  /* NMI Interrupt Flag */
//#define Reserved          (0x0020)
#define JMBINIFG_L          (0x0040)  /* JTAG Mail Box input Interrupt Flag */
#define JMBOUTIFG_L         (0x0080)  /* JTAG Mail Box output Interrupt Flag */

//#define Reserved          (0x0004)
//#define Reserved          (0x0020)

#define SFRRPCR_              0x0104    /* RESET Pin Control Register */
sfrb(SFRRPCR_L, SFRRPCR_);
sfrb(SFRRPCR_H, SFRRPCR_+1);
sfrw(SFRRPCR, SFRRPCR_);
/* SFRRPCR Control Bits */
#define SYSNMI              (0x0001)  /* NMI select */
#define SYSNMIIES           (0x0002)  /* NMI edge select */
#define SYSRSTUP            (0x0004)  /* RESET Pin pull down/up select */
#define SYSRSTRE            (0x0008)  /* RESET Pin Resistor enable */

#define SYSNMI_L            (0x0001)  /* NMI select */
#define SYSNMIIES_L         (0x0002)  /* NMI edge select */
#define SYSRSTUP_L          (0x0004)  /* RESET Pin pull down/up select */
#define SYSRSTRE_L          (0x0008)  /* RESET Pin Resistor enable */


/************************************************************
* SYS - System Module
************************************************************/
#define __MSP430_HAS_SYS__            /* Definition to show that Module is available */

#define SYSCTL_               0x0180    /* System control */
sfrb(SYSCTL_L, SYSCTL_);
sfrb(SYSCTL_H, SYSCTL_+1);
sfrw(SYSCTL, SYSCTL_);
#define SYSBSLC_              0x0182    /* Boot strap configuration area */
sfrb(SYSBSLC_L, SYSBSLC_);
sfrb(SYSBSLC_H, SYSBSLC_+1);
sfrw(SYSBSLC, SYSBSLC_);
#define SYSJMBC_              0x0186    /* JTAG mailbox control */
sfrb(SYSJMBC_L, SYSJMBC_);
sfrb(SYSJMBC_H, SYSJMBC_+1);
sfrw(SYSJMBC, SYSJMBC_);
#define SYSJMBI0_             0x0188    /* JTAG mailbox input 0 */
sfrb(SYSJMBI0_L, SYSJMBI0_);
sfrb(SYSJMBI0_H, SYSJMBI0_+1);
sfrw(SYSJMBI0, SYSJMBI0_);
#define SYSJMBI1_             0x018A    /* JTAG mailbox input 1 */
sfrb(SYSJMBI1_L, SYSJMBI1_);
sfrb(SYSJMBI1_H, SYSJMBI1_+1);
sfrw(SYSJMBI1, SYSJMBI1_);
#define SYSJMBO0_             0x018C    /* JTAG mailbox output 0 */
sfrb(SYSJMBO0_L, SYSJMBO0_);
sfrb(SYSJMBO0_H, SYSJMBO0_+1);
sfrw(SYSJMBO0, SYSJMBO0_);
#define SYSJMBO1_             0x018E    /* JTAG mailbox output 1 */
sfrb(SYSJMBO1_L, SYSJMBO1_);
sfrb(SYSJMBO1_H, SYSJMBO1_+1);
sfrw(SYSJMBO1, SYSJMBO1_);

#define SYSBERRIV_            0x0198    /* Bus Error vector generator */
sfrb(SYSBERRIV_L, SYSBERRIV_);
sfrb(SYSBERRIV_H, SYSBERRIV_+1);
sfrw(SYSBERRIV, SYSBERRIV_);
#define SYSUNIV_              0x019A    /* User NMI vector generator */
sfrb(SYSUNIV_L, SYSUNIV_);
sfrb(SYSUNIV_H, SYSUNIV_+1);
sfrw(SYSUNIV, SYSUNIV_);
#define SYSSNIV_              0x019C    /* System NMI vector generator */
sfrb(SYSSNIV_L, SYSSNIV_);
sfrb(SYSSNIV_H, SYSSNIV_+1);
sfrw(SYSSNIV, SYSSNIV_);
#define SYSRSTIV_             0x019E    /* Reset vector generator */
sfrb(SYSRSTIV_L, SYSRSTIV_);
sfrb(SYSRSTIV_H, SYSRSTIV_+1);
sfrw(SYSRSTIV, SYSRSTIV_);

/* SYSCTL Control Bits */
#define SYSRIVECT           (0x0001)  /* SYS - RAM based interrupt vectors */
//#define RESERVED            (0x0002)  /* SYS - Reserved */
#define SYSPMMPE            (0x0004)  /* SYS - PMM access protect */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
#define SYSBSLIND           (0x0010)  /* SYS - TCK/RST indication detected */
#define SYSJTAGPIN          (0x0020)  /* SYS - Dedicated JTAG pins enabled */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSCTL Control Bits */
#define SYSRIVECT_L         (0x0001)  /* SYS - RAM based interrupt vectors */
//#define RESERVED            (0x0002)  /* SYS - Reserved */
#define SYSPMMPE_L          (0x0004)  /* SYS - PMM access protect */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
#define SYSBSLIND_L         (0x0010)  /* SYS - TCK/RST indication detected */
#define SYSJTAGPIN_L        (0x0020)  /* SYS - Dedicated JTAG pins enabled */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSCTL Control Bits */
//#define RESERVED            (0x0002)  /* SYS - Reserved */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSBSLC Control Bits */
#define SYSBSLSIZE0         (0x0001)  /* SYS - BSL Protection Size 0 */
#define SYSBSLSIZE1         (0x0002)  /* SYS - BSL Protection Size 1 */
#define SYSBSLR             (0x0004)  /* SYS - RAM assigned to BSL */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
//#define RESERVED            (0x0010)  /* SYS - Reserved */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
#define SYSBSLOFF           (0x4000)  /* SYS - BSL Memeory disabled */
#define SYSBSLPE            (0x8000)  /* SYS - BSL Memory protection enabled */

/* SYSBSLC Control Bits */
#define SYSBSLSIZE0_L       (0x0001)  /* SYS - BSL Protection Size 0 */
#define SYSBSLSIZE1_L       (0x0002)  /* SYS - BSL Protection Size 1 */
#define SYSBSLR_L           (0x0004)  /* SYS - RAM assigned to BSL */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
//#define RESERVED            (0x0010)  /* SYS - Reserved */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */

/* SYSBSLC Control Bits */
//#define RESERVED            (0x0008)  /* SYS - Reserved */
//#define RESERVED            (0x0010)  /* SYS - Reserved */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
//#define RESERVED            (0x0040)  /* SYS - Reserved */
//#define RESERVED            (0x0080)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
#define SYSBSLOFF_H         (0x0040)  /* SYS - BSL Memeory disabled */
#define SYSBSLPE_H          (0x0080)  /* SYS - BSL Memory protection enabled */

/* SYSJMBC Control Bits */
#define JMBIN0FG            (0x0001)  /* SYS - Incoming JTAG Mailbox 0 Flag */
#define JMBIN1FG            (0x0002)  /* SYS - Incoming JTAG Mailbox 1 Flag */
#define JMBOUT0FG           (0x0004)  /* SYS - Outgoing JTAG Mailbox 0 Flag */
#define JMBOUT1FG           (0x0008)  /* SYS - Outgoing JTAG Mailbox 1 Flag */
#define JMBMODE             (0x0010)  /* SYS - JMB 16/32 Bit Mode */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
#define JMBCLR0OFF          (0x0040)  /* SYS - Incoming JTAG Mailbox 0 Flag auto-clear disalbe */
#define JMBCLR1OFF          (0x0080)  /* SYS - Incoming JTAG Mailbox 1 Flag auto-clear disalbe */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSJMBC Control Bits */
#define JMBIN0FG_L          (0x0001)  /* SYS - Incoming JTAG Mailbox 0 Flag */
#define JMBIN1FG_L          (0x0002)  /* SYS - Incoming JTAG Mailbox 1 Flag */
#define JMBOUT0FG_L         (0x0004)  /* SYS - Outgoing JTAG Mailbox 0 Flag */
#define JMBOUT1FG_L         (0x0008)  /* SYS - Outgoing JTAG Mailbox 1 Flag */
#define JMBMODE_L           (0x0010)  /* SYS - JMB 16/32 Bit Mode */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
#define JMBCLR0OFF_L        (0x0040)  /* SYS - Incoming JTAG Mailbox 0 Flag auto-clear disalbe */
#define JMBCLR1OFF_L        (0x0080)  /* SYS - Incoming JTAG Mailbox 1 Flag auto-clear disalbe */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSJMBC Control Bits */
//#define RESERVED            (0x0020)  /* SYS - Reserved */
//#define RESERVED            (0x0100)  /* SYS - Reserved */
//#define RESERVED            (0x0200)  /* SYS - Reserved */
//#define RESERVED            (0x0400)  /* SYS - Reserved */
//#define RESERVED            (0x0800)  /* SYS - Reserved */
//#define RESERVED            (0x1000)  /* SYS - Reserved */
//#define RESERVED            (0x2000)  /* SYS - Reserved */
//#define RESERVED            (0x4000)  /* SYS - Reserved */
//#define RESERVED            (0x8000)  /* SYS - Reserved */

/* SYSUNIV Definitions */
#define SYSUNIV_NONE       (0x0000)    /* No Interrupt pending */
#define SYSUNIV_NMIIFG     (0x0002)    /* SYSUNIV : NMIIFG */
#define SYSUNIV_OFIFG      (0x0004)    /* SYSUNIV : Osc. Fail - OFIFG */
#define SYSUNIV_ACCVIFG    (0x0006)    /* SYSUNIV : Access Violation - ACCVIFG */
#define SYSUNIV_BUSIFG     (0x0008)    /* SYSUNIV : Bus Error */
#define SYSUNIV_SYSBUSIV   (0x0008)    /* SYSUNIV : Bus Error - SYSBERRIFG (legacy) */

/* SYSSNIV Definitions */
#define SYSSNIV_NONE       (0x0000)    /* No Interrupt pending */
#define SYSSNIV_SVMLIFG    (0x0002)    /* SYSSNIV : SVMLIFG */
#define SYSSNIV_SVMHIFG    (0x0004)    /* SYSSNIV : SVMHIFG */
#define SYSSNIV_DLYLIFG    (0x0006)    /* SYSSNIV : DLYLIFG */
#define SYSSNIV_DLYHIFG    (0x0008)    /* SYSSNIV : DLYHIFG */
#define SYSSNIV_VMAIFG     (0x000A)    /* SYSSNIV : VMAIFG */
#define SYSSNIV_JMBINIFG   (0x000C)    /* SYSSNIV : JMBINIFG */
#define SYSSNIV_JMBOUTIFG  (0x000E)    /* SYSSNIV : JMBOUTIFG */
#define SYSSNIV_VLRLIFG    (0x0010)    /* SYSSNIV : VLRLIFG */
#define SYSSNIV_VLRHIFG    (0x0012)    /* SYSSNIV : VLRHIFG */

/* SYSRSTIV Definitions */
#define SYSRSTIV_NONE      (0x0000)    /* No Interrupt pending */
#define SYSRSTIV_BOR       (0x0002)    /* SYSRSTIV : BOR */
#define SYSRSTIV_RSTNMI    (0x0004)    /* SYSRSTIV : RST/NMI */
#define SYSRSTIV_DOBOR     (0x0006)    /* SYSRSTIV : Do BOR */
#define SYSRSTIV_LPM5WU    (0x0008)    /* SYSRSTIV : Port LPM5 Wake Up */
#define SYSRSTIV_SECYV     (0x000A)    /* SYSRSTIV : Security violation */
#define SYSRSTIV_SVSL      (0x000C)    /* SYSRSTIV : SVSL */
#define SYSRSTIV_SVSH      (0x000E)    /* SYSRSTIV : SVSH */
#define SYSRSTIV_SVML_OVP  (0x0010)    /* SYSRSTIV : SVML_OVP */
#define SYSRSTIV_SVMH_OVP  (0x0012)    /* SYSRSTIV : SVMH_OVP */
#define SYSRSTIV_DOPOR     (0x0014)    /* SYSRSTIV : Do POR */
#define SYSRSTIV_WDTTO     (0x0016)    /* SYSRSTIV : WDT Time out */
#define SYSRSTIV_WDTKEY    (0x0018)    /* SYSRSTIV : WDTKEY violation */
#define SYSRSTIV_KEYV      (0x001A)    /* SYSRSTIV : Flash Key violation */
#define SYSRSTIV_FLLUL     (0x001C)    /* SYSRSTIV : FLL unlock */
#define SYSRSTIV_PERF      (0x001E)    /* SYSRSTIV : peripheral/config area fetch */
#define SYSRSTIV_PMMKEY    (0x0020)    /* SYSRSTIV : PMMKEY violation */

/************************************************************
* Timer0_A5
************************************************************/
#define __MSP430_HAS_T0A5__           /* Definition to show that Module is available */
                                                  
#define TA0CTL_               0x0340    /* Timer0_A5 Control */
sfrb(TA0CTL_L, TA0CTL_);
sfrb(TA0CTL_H, TA0CTL_+1);
sfrw(TA0CTL, TA0CTL_);
#define TA0CCTL0_             0x0342    /* Timer0_A5 Capture/Compare Control 0 */
sfrb(TA0CCTL0_L, TA0CCTL0_);
sfrb(TA0CCTL0_H, TA0CCTL0_+1);
sfrw(TA0CCTL0, TA0CCTL0_);
#define TA0CCTL1_             0x0344    /* Timer0_A5 Capture/Compare Control 1 */
sfrb(TA0CCTL1_L, TA0CCTL1_);
sfrb(TA0CCTL1_H, TA0CCTL1_+1);
sfrw(TA0CCTL1, TA0CCTL1_);
#define TA0CCTL2_             0x0346    /* Timer0_A5 Capture/Compare Control 2 */
sfrb(TA0CCTL2_L, TA0CCTL2_);
sfrb(TA0CCTL2_H, TA0CCTL2_+1);
sfrw(TA0CCTL2, TA0CCTL2_);
#define TA0CCTL3_             0x0348    /* Timer0_A5 Capture/Compare Control 3 */
sfrb(TA0CCTL3_L, TA0CCTL3_);
sfrb(TA0CCTL3_H, TA0CCTL3_+1);
sfrw(TA0CCTL3, TA0CCTL3_);
#define TA0CCTL4_             0x034A    /* Timer0_A5 Capture/Compare Control 4 */
sfrb(TA0CCTL4_L, TA0CCTL4_);
sfrb(TA0CCTL4_H, TA0CCTL4_+1);
sfrw(TA0CCTL4, TA0CCTL4_);
#define TA0R_                 0x0350    /* Timer0_A5 */
sfrb(TA0R_L, TA0R_);
sfrb(TA0R_H, TA0R_+1);
sfrw(TA0R, TA0R_);
#define TA0CCR0_              0x0352    /* Timer0_A5 Capture/Compare 0 */
sfrb(TA0CCR0_L, TA0CCR0_);
sfrb(TA0CCR0_H, TA0CCR0_+1);
sfrw(TA0CCR0, TA0CCR0_);
#define TA0CCR1_              0x0354    /* Timer0_A5 Capture/Compare 1 */
sfrb(TA0CCR1_L, TA0CCR1_);
sfrb(TA0CCR1_H, TA0CCR1_+1);
sfrw(TA0CCR1, TA0CCR1_);
#define TA0CCR2_              0x0356    /* Timer0_A5 Capture/Compare 2 */
sfrb(TA0CCR2_L, TA0CCR2_);
sfrb(TA0CCR2_H, TA0CCR2_+1);
sfrw(TA0CCR2, TA0CCR2_);
#define TA0CCR3_              0x0358    /* Timer0_A5 Capture/Compare 3 */
sfrb(TA0CCR3_L, TA0CCR3_);
sfrb(TA0CCR3_H, TA0CCR3_+1);
sfrw(TA0CCR3, TA0CCR3_);
#define TA0CCR4_              0x035A    /* Timer0_A5 Capture/Compare 4 */
sfrb(TA0CCR4_L, TA0CCR4_);
sfrb(TA0CCR4_H, TA0CCR4_+1);
sfrw(TA0CCR4, TA0CCR4_);
#define TA0IV_                0x036E    /* Timer0_A5 Interrupt Vector Word */
sfrb(TA0IV_L, TA0IV_);
sfrb(TA0IV_H, TA0IV_+1);
sfrw(TA0IV, TA0IV_);
#define TA0EX0_               0x0360    /* Timer0_A5 Expansion Register 0 */
sfrb(TA0EX0_L, TA0EX0_);
sfrb(TA0EX0_H, TA0EX0_+1);
sfrw(TA0EX0, TA0EX0_);

/* TAxCTL Control Bits */
#define TASSEL1             (0x0200)  /* Timer A clock source select 0 */
#define TASSEL0             (0x0100)  /* Timer A clock source select 1 */
#define ID1                 (0x0080)  /* Timer A clock input divider 1 */
#define ID0                 (0x0040)  /* Timer A clock input divider 0 */
#define MC1                 (0x0020)  /* Timer A mode control 1 */
#define MC0                 (0x0010)  /* Timer A mode control 0 */
#define TACLR               (0x0004)  /* Timer A counter clear */
#define TAIE                (0x0002)  /* Timer A counter interrupt enable */
#define TAIFG               (0x0001)  /* Timer A counter interrupt flag */

/* TAxCTL Control Bits */
#define ID1_L               (0x0080)  /* Timer A clock input divider 1 */
#define ID0_L               (0x0040)  /* Timer A clock input divider 0 */
#define MC1_L               (0x0020)  /* Timer A mode control 1 */
#define MC0_L               (0x0010)  /* Timer A mode control 0 */
#define TACLR_L             (0x0004)  /* Timer A counter clear */
#define TAIE_L              (0x0002)  /* Timer A counter interrupt enable */
#define TAIFG_L             (0x0001)  /* Timer A counter interrupt flag */

/* TAxCTL Control Bits */
#define TASSEL1_H           (0x0002)  /* Timer A clock source select 0 */
#define TASSEL0_H           (0x0001)  /* Timer A clock source select 1 */

#define MC_0                (0*0x10)  /* Timer A mode control: 0 - Stop */
#define MC_1                (1*0x10)  /* Timer A mode control: 1 - Up to CCR0 */
#define MC_2                (2*0x10)  /* Timer A mode control: 2 - Continous up */
#define MC_3                (3*0x10)  /* Timer A mode control: 3 - Up/Down */
#define ID_0                (0*0x40)  /* Timer A input divider: 0 - /1 */
#define ID_1                (1*0x40)  /* Timer A input divider: 1 - /2 */
#define ID_2                (2*0x40)  /* Timer A input divider: 2 - /4 */
#define ID_3                (3*0x40)  /* Timer A input divider: 3 - /8 */
#define TASSEL_0            (0*0x100) /* Timer A clock source select: 0 - TACLK */
#define TASSEL_1            (1*0x100) /* Timer A clock source select: 1 - ACLK  */
#define TASSEL_2            (2*0x100) /* Timer A clock source select: 2 - SMCLK */
#define TASSEL_3            (3*0x100) /* Timer A clock source select: 3 - INCLK */
#define MC__STOP            (0*0x10)  /* Timer A mode control: 0 - Stop */
#define MC__UP              (1*0x10)  /* Timer A mode control: 1 - Up to CCR0 */
#define MC__CONTINOUS       (2*0x10)  /* Timer A mode control: 2 - Continous up */
#define MC__UPDOWN          (3*0x10)  /* Timer A mode control: 3 - Up/Down */
#define ID__1               (0*0x40)  /* Timer A input divider: 0 - /1 */
#define ID__2               (1*0x40)  /* Timer A input divider: 1 - /2 */
#define ID__4               (2*0x40)  /* Timer A input divider: 2 - /4 */
#define ID__8               (3*0x40)  /* Timer A input divider: 3 - /8 */
#define TASSEL__TACLK       (0*0x100) /* Timer A clock source select: 0 - TACLK */
#define TASSEL__ACLK        (1*0x100) /* Timer A clock source select: 1 - ACLK  */
#define TASSEL__SMCLK       (2*0x100) /* Timer A clock source select: 2 - SMCLK */
#define TASSEL__INCLK       (3*0x100) /* Timer A clock source select: 3 - INCLK */

/* TAxCCTLx Control Bits */
#define CM1                 (0x8000)  /* Capture mode 1 */
#define CM0                 (0x4000)  /* Capture mode 0 */
#define CCIS1               (0x2000)  /* Capture input select 1 */
#define CCIS0               (0x1000)  /* Capture input select 0 */
#define SCS                 (0x0800)  /* Capture sychronize */
#define SCCI                (0x0400)  /* Latched capture signal (read) */
#define CAP                 (0x0100)  /* Capture mode: 1 /Compare mode : 0 */
#define OUTMOD2             (0x0080)  /* Output mode 2 */
#define OUTMOD1             (0x0040)  /* Output mode 1 */
#define OUTMOD0             (0x0020)  /* Output mode 0 */
#define CCIE                (0x0010)  /* Capture/compare interrupt enable */
#define CCI                 (0x0008)  /* Capture input signal (read) */
#define OUT                 (0x0004)  /* PWM Output signal if output mode 0 */
#define COV                 (0x0002)  /* Capture/compare overflow flag */
#define CCIFG               (0x0001)  /* Capture/compare interrupt flag */

/* TAxCCTLx Control Bits */
#define OUTMOD2_L           (0x0080)  /* Output mode 2 */
#define OUTMOD1_L           (0x0040)  /* Output mode 1 */
#define OUTMOD0_L           (0x0020)  /* Output mode 0 */
#define CCIE_L              (0x0010)  /* Capture/compare interrupt enable */
#define CCI_L               (0x0008)  /* Capture input signal (read) */
#define OUT_L               (0x0004)  /* PWM Output signal if output mode 0 */
#define COV_L               (0x0002)  /* Capture/compare overflow flag */
#define CCIFG_L             (0x0001)  /* Capture/compare interrupt flag */

/* TAxCCTLx Control Bits */
#define CM1_H               (0x0080)  /* Capture mode 1 */
#define CM0_H               (0x0040)  /* Capture mode 0 */
#define CCIS1_H             (0x0020)  /* Capture input select 1 */
#define CCIS0_H             (0x0010)  /* Capture input select 0 */
#define SCS_H               (0x0008)  /* Capture sychronize */
#define SCCI_H              (0x0004)  /* Latched capture signal (read) */
#define CAP_H               (0x0001)  /* Capture mode: 1 /Compare mode : 0 */

#define OUTMOD_0            (0*0x20)  /* PWM output mode: 0 - output only */
#define OUTMOD_1            (1*0x20)  /* PWM output mode: 1 - set */
#define OUTMOD_2            (2*0x20)  /* PWM output mode: 2 - PWM toggle/reset */
#define OUTMOD_3            (3*0x20)  /* PWM output mode: 3 - PWM set/reset */
#define OUTMOD_4            (4*0x20)  /* PWM output mode: 4 - toggle */
#define OUTMOD_5            (5*0x20)  /* PWM output mode: 5 - Reset */
#define OUTMOD_6            (6*0x20)  /* PWM output mode: 6 - PWM toggle/set */
#define OUTMOD_7            (7*0x20)  /* PWM output mode: 7 - PWM reset/set */
#define CCIS_0              (0U*0x1000) /* Capture input select: 0 - CCIxA */
#define CCIS_1              (1U*0x1000) /* Capture input select: 1 - CCIxB */
#define CCIS_2              (2U*0x1000) /* Capture input select: 2 - GND */
#define CCIS_3              (3U*0x1000) /* Capture input select: 3 - Vcc */
#define CM_0                (0U*0x4000) /* Capture mode: 0 - disabled */
#define CM_1                (1U*0x4000) /* Capture mode: 1 - pos. edge */
#define CM_2                (2U*0x4000) /* Capture mode: 1 - neg. edge */
#define CM_3                (3U*0x4000) /* Capture mode: 1 - both edges */


/* TAxEX0 Control Bits */
#define TAIDEX0             (0x0001)  /* Timer A Input divider expansion Bit: 0 */
#define TAIDEX1             (0x0002)  /* Timer A Input divider expansion Bit: 1 */
#define TAIDEX2             (0x0004)  /* Timer A Input divider expansion Bit: 2 */

/* TAxEX0 Control Bits */
#define TAIDEX0_L           (0x0001)  /* Timer A Input divider expansion Bit: 0 */
#define TAIDEX1_L           (0x0002)  /* Timer A Input divider expansion Bit: 1 */
#define TAIDEX2_L           (0x0004)  /* Timer A Input divider expansion Bit: 2 */

/* TAxEX0 Control Bits */

#define TAIDEX_0            (0U*0x0001) /* Timer A Input divider expansion : /1 */
#define TAIDEX_1            (1U*0x0001) /* Timer A Input divider expansion : /2 */
#define TAIDEX_2            (2U*0x0001) /* Timer A Input divider expansion : /3 */
#define TAIDEX_3            (3U*0x0001) /* Timer A Input divider expansion : /4 */
#define TAIDEX_4            (4U*0x0001) /* Timer A Input divider expansion : /5 */
#define TAIDEX_5            (5U*0x0001) /* Timer A Input divider expansion : /6 */
#define TAIDEX_6            (6U*0x0001) /* Timer A Input divider expansion : /7 */
#define TAIDEX_7            (7U*0x0001) /* Timer A Input divider expansion : /8 */

/* T0A5IV Definitions */
#define TA0IV_NONE          (0x0000)    /* No Interrupt pending */
#define TA0IV_TA0CCR1       (0x0002)    /* TA0CCR1_CCIFG */
#define TA0IV_TA0CCR2       (0x0004)    /* TA0CCR2_CCIFG */
#define TA0IV_TA0CCR3       (0x0006)    /* TA0CCR3_CCIFG */
#define TA0IV_TA0CCR4       (0x0008)    /* TA0CCR4_CCIFG */
#define TA0IV_5             (0x000A)    /* Reserved */
#define TA0IV_6             (0x000C)    /* Reserved */
#define TA0IV_TA0IFG        (0x000E)    /* TA0IFG */

/************************************************************
* Timer1_A3
************************************************************/
#define __MSP430_HAS_T1A3__            /* Definition to show that Module is available */

#define TA1CTL_               0x0380    /* Timer1_A3 Control */
sfrb(TA1CTL_L, TA1CTL_);
sfrb(TA1CTL_H, TA1CTL_+1);
sfrw(TA1CTL, TA1CTL_);
#define TA1CCTL0_             0x0382    /* Timer1_A3 Capture/Compare Control 0 */
sfrb(TA1CCTL0_L, TA1CCTL0_);
sfrb(TA1CCTL0_H, TA1CCTL0_+1);
sfrw(TA1CCTL0, TA1CCTL0_);
#define TA1CCTL1_             0x0384    /* Timer1_A3 Capture/Compare Control 1 */
sfrb(TA1CCTL1_L, TA1CCTL1_);
sfrb(TA1CCTL1_H, TA1CCTL1_+1);
sfrw(TA1CCTL1, TA1CCTL1_);
#define TA1CCTL2_             0x0386    /* Timer1_A3 Capture/Compare Control 2 */
sfrb(TA1CCTL2_L, TA1CCTL2_);
sfrb(TA1CCTL2_H, TA1CCTL2_+1);
sfrw(TA1CCTL2, TA1CCTL2_);
#define TA1R_                 0x0390    /* Timer1_A3 */
sfrb(TA1R_L, TA1R_);
sfrb(TA1R_H, TA1R_+1);
sfrw(TA1R, TA1R_);
#define TA1CCR0_              0x0392    /* Timer1_A3 Capture/Compare 0 */
sfrb(TA1CCR0_L, TA1CCR0_);
sfrb(TA1CCR0_H, TA1CCR0_+1);
sfrw(TA1CCR0, TA1CCR0_);
#define TA1CCR1_              0x0394    /* Timer1_A3 Capture/Compare 1 */
sfrb(TA1CCR1_L, TA1CCR1_);
sfrb(TA1CCR1_H, TA1CCR1_+1);
sfrw(TA1CCR1, TA1CCR1_);
#define TA1CCR2_              0x0396    /* Timer1_A3 Capture/Compare 2 */
sfrb(TA1CCR2_L, TA1CCR2_);
sfrb(TA1CCR2_H, TA1CCR2_+1);
sfrw(TA1CCR2, TA1CCR2_);
#define TA1IV_                0x03AE    /* Timer1_A3 Interrupt Vector Word */
sfrb(TA1IV_L, TA1IV_);
sfrb(TA1IV_H, TA1IV_+1);
sfrw(TA1IV, TA1IV_);
#define TA1EX0_               0x03A0    /* Timer1_A3 Expansion Register 0 */
sfrb(TA1EX0_L, TA1EX0_);
sfrb(TA1EX0_H, TA1EX0_+1);
sfrw(TA1EX0, TA1EX0_);

/* Bits are already defined within the Timer0_Ax */

/* TA1IV Definitions */
#define TA1IV_NONE          (0x0000)    /* No Interrupt pending */
#define TA1IV_TA1CCR1       (0x0002)    /* TA1CCR1_CCIFG */
#define TA1IV_TA1CCR2       (0x0004)    /* TA1CCR2_CCIFG */
#define TA1IV_3             (0x0006)    /* Reserved */
#define TA1IV_4             (0x0008)    /* Reserved */
#define TA1IV_5             (0x000A)    /* Reserved */
#define TA1IV_6             (0x000C)    /* Reserved */
#define TA1IV_TA1IFG        (0x000E)    /* TA1IFG */

/************************************************************
* Timer2_A3
************************************************************/
#define __MSP430_HAS_T2A3__            /* Definition to show that Module is available */

#define TA2CTL_               0x0400    /* Timer2_A3 Control */
sfrb(TA2CTL_L, TA2CTL_);
sfrb(TA2CTL_H, TA2CTL_+1);
sfrw(TA2CTL, TA2CTL_);
#define TA2CCTL0_             0x0402    /* Timer2_A3 Capture/Compare Control 0 */
sfrb(TA2CCTL0_L, TA2CCTL0_);
sfrb(TA2CCTL0_H, TA2CCTL0_+1);
sfrw(TA2CCTL0, TA2CCTL0_);
#define TA2CCTL1_             0x0404    /* Timer2_A3 Capture/Compare Control 1 */
sfrb(TA2CCTL1_L, TA2CCTL1_);
sfrb(TA2CCTL1_H, TA2CCTL1_+1);
sfrw(TA2CCTL1, TA2CCTL1_);
#define TA2CCTL2_             0x0406    /* Timer2_A3 Capture/Compare Control 2 */
sfrb(TA2CCTL2_L, TA2CCTL2_);
sfrb(TA2CCTL2_H, TA2CCTL2_+1);
sfrw(TA2CCTL2, TA2CCTL2_);
#define TA2R_                 0x0410    /* Timer2_A3 */
sfrb(TA2R_L, TA2R_);
sfrb(TA2R_H, TA2R_+1);
sfrw(TA2R, TA2R_);
#define TA2CCR0_              0x0412    /* Timer2_A3 Capture/Compare 0 */
sfrb(TA2CCR0_L, TA2CCR0_);
sfrb(TA2CCR0_H, TA2CCR0_+1);
sfrw(TA2CCR0, TA2CCR0_);
#define TA2CCR1_              0x0414    /* Timer2_A3 Capture/Compare 1 */
sfrb(TA2CCR1_L, TA2CCR1_);
sfrb(TA2CCR1_H, TA2CCR1_+1);
sfrw(TA2CCR1, TA2CCR1_);
#define TA2CCR2_              0x0416    /* Timer2_A3 Capture/Compare 2 */
sfrb(TA2CCR2_L, TA2CCR2_);
sfrb(TA2CCR2_H, TA2CCR2_+1);
sfrw(TA2CCR2, TA2CCR2_);
#define TA2IV_                0x042E    /* Timer2_A3 Interrupt Vector Word */
sfrb(TA2IV_L, TA2IV_);
sfrb(TA2IV_H, TA2IV_+1);
sfrw(TA2IV, TA2IV_);
#define TA2EX0_               0x0420    /* Timer2_A3 Expansion Register 0 */
sfrb(TA2EX0_L, TA2EX0_);
sfrb(TA2EX0_H, TA2EX0_+1);
sfrw(TA2EX0, TA2EX0_);

/* Bits are already defined within the Timer0_Ax */

/* TA2IV Definitions */
#define TA2IV_NONE          (0x0000)    /* No Interrupt pending */
#define TA2IV_TA1CCR1       (0x0002)    /* TA2CCR1_CCIFG */
#define TA2IV_TA1CCR2       (0x0004)    /* TA2CCR2_CCIFG */
#define TA2IV_3             (0x0006)    /* Reserved */
#define TA2IV_4             (0x0008)    /* Reserved */
#define TA2IV_5             (0x000A)    /* Reserved */
#define TA2IV_6             (0x000C)    /* Reserved */
#define TA2IV_TA2IFG        (0x000E)    /* TA2IFG */

/************************************************************
* Timer0_B7
************************************************************/
#define __MSP430_HAS_T0B7__            /* Definition to show that Module is available */

#define TB0CTL_               0x03C0    /* Timer0_B7 Control */
sfrb(TB0CTL_L, TB0CTL_);
sfrb(TB0CTL_H, TB0CTL_+1);
sfrw(TB0CTL, TB0CTL_);
#define TB0CCTL0_             0x03C2    /* Timer0_B7 Capture/Compare Control 0 */
sfrb(TB0CCTL0_L, TB0CCTL0_);
sfrb(TB0CCTL0_H, TB0CCTL0_+1);
sfrw(TB0CCTL0, TB0CCTL0_);
#define TB0CCTL1_             0x03C4    /* Timer0_B7 Capture/Compare Control 1 */
sfrb(TB0CCTL1_L, TB0CCTL1_);
sfrb(TB0CCTL1_H, TB0CCTL1_+1);
sfrw(TB0CCTL1, TB0CCTL1_);
#define TB0CCTL2_             0x03C6    /* Timer0_B7 Capture/Compare Control 2 */
sfrb(TB0CCTL2_L, TB0CCTL2_);
sfrb(TB0CCTL2_H, TB0CCTL2_+1);
sfrw(TB0CCTL2, TB0CCTL2_);
#define TB0CCTL3_             0x03C8    /* Timer0_B7 Capture/Compare Control 3 */
sfrb(TB0CCTL3_L, TB0CCTL3_);
sfrb(TB0CCTL3_H, TB0CCTL3_+1);
sfrw(TB0CCTL3, TB0CCTL3_);
#define TB0CCTL4_             0x03CA    /* Timer0_B7 Capture/Compare Control 4 */
sfrb(TB0CCTL4_L, TB0CCTL4_);
sfrb(TB0CCTL4_H, TB0CCTL4_+1);
sfrw(TB0CCTL4, TB0CCTL4_);
#define TB0CCTL5_             0x03CC    /* Timer0_B7 Capture/Compare Control 5 */
sfrb(TB0CCTL5_L, TB0CCTL5_);
sfrb(TB0CCTL5_H, TB0CCTL5_+1);
sfrw(TB0CCTL5, TB0CCTL5_);
#define TB0CCTL6_             0x03CE    /* Timer0_B7 Capture/Compare Control 6 */
sfrb(TB0CCTL6_L, TB0CCTL6_);
sfrb(TB0CCTL6_H, TB0CCTL6_+1);
sfrw(TB0CCTL6, TB0CCTL6_);
#define TB0R_                 0x03D0    /* Timer0_B7 */
sfrb(TB0R_L, TB0R_);
sfrb(TB0R_H, TB0R_+1);
sfrw(TB0R, TB0R_);
#define TB0CCR0_              0x03D2    /* Timer0_B7 Capture/Compare 0 */
sfrb(TB0CCR0_L, TB0CCR0_);
sfrb(TB0CCR0_H, TB0CCR0_+1);
sfrw(TB0CCR0, TB0CCR0_);
#define TB0CCR1_              0x03D4    /* Timer0_B7 Capture/Compare 1 */
sfrb(TB0CCR1_L, TB0CCR1_);
sfrb(TB0CCR1_H, TB0CCR1_+1);
sfrw(TB0CCR1, TB0CCR1_);
#define TB0CCR2_              0x03D6    /* Timer0_B7 Capture/Compare 2 */
sfrb(TB0CCR2_L, TB0CCR2_);
sfrb(TB0CCR2_H, TB0CCR2_+1);
sfrw(TB0CCR2, TB0CCR2_);
#define TB0CCR3_              0x03D8    /* Timer0_B7 Capture/Compare 3 */
sfrb(TB0CCR3_L, TB0CCR3_);
sfrb(TB0CCR3_H, TB0CCR3_+1);
sfrw(TB0CCR3, TB0CCR3_);
#define TB0CCR4_              0x03DA    /* Timer0_B7 Capture/Compare 4 */
sfrb(TB0CCR4_L, TB0CCR4_);
sfrb(TB0CCR4_H, TB0CCR4_+1);
sfrw(TB0CCR4, TB0CCR4_);
#define TB0CCR5_              0x03DC    /* Timer0_B7 Capture/Compare 5 */
sfrb(TB0CCR5_L, TB0CCR5_);
sfrb(TB0CCR5_H, TB0CCR5_+1);
sfrw(TB0CCR5, TB0CCR5_);
#define TB0CCR6_              0x03DE    /* Timer0_B7 Capture/Compare 6 */
sfrb(TB0CCR6_L, TB0CCR6_);
sfrb(TB0CCR6_H, TB0CCR6_+1);
sfrw(TB0CCR6, TB0CCR6_);
#define TB0EX0_               0x03E0    /* Timer0_B7 Expansion Register 0 */
sfrb(TB0EX0_L, TB0EX0_);
sfrb(TB0EX0_H, TB0EX0_+1);
sfrw(TB0EX0, TB0EX0_);
#define TB0IV_                0x03EE    /* Timer0_B7 Interrupt Vector Word */
sfrb(TB0IV_L, TB0IV_);
sfrb(TB0IV_H, TB0IV_+1);
sfrw(TB0IV, TB0IV_);

/* Legacy Type Definitions for TimerB */
#define TBCTL                TB0CTL    /* Timer0_B7 Control */
#define TBCCTL0              TB0CCTL0  /* Timer0_B7 Capture/Compare Control 0 */
#define TBCCTL1              TB0CCTL1  /* Timer0_B7 Capture/Compare Control 1 */
#define TBCCTL2              TB0CCTL2  /* Timer0_B7 Capture/Compare Control 2 */
#define TBCCTL3              TB0CCTL3  /* Timer0_B7 Capture/Compare Control 3 */
#define TBCCTL4              TB0CCTL4  /* Timer0_B7 Capture/Compare Control 4 */
#define TBCCTL5              TB0CCTL5  /* Timer0_B7 Capture/Compare Control 5 */
#define TBCCTL6              TB0CCTL6  /* Timer0_B7 Capture/Compare Control 6 */
#define TBR                  TB0R      /* Timer0_B7 */
#define TBCCR0               TB0CCR0   /* Timer0_B7 Capture/Compare 0 */
#define TBCCR1               TB0CCR1   /* Timer0_B7 Capture/Compare 1 */
#define TBCCR2               TB0CCR2   /* Timer0_B7 Capture/Compare 2 */
#define TBCCR3               TB0CCR3   /* Timer0_B7 Capture/Compare 3 */
#define TBCCR4               TB0CCR4   /* Timer0_B7 Capture/Compare 4 */
#define TBCCR5               TB0CCR5   /* Timer0_B7 Capture/Compare 5 */
#define TBCCR6               TB0CCR6   /* Timer0_B7 Capture/Compare 6 */
#define TBEX0                TB0EX0    /* Timer0_B7 Expansion Register 0 */
#define TBIV                 TB0IV     /* Timer0_B7 Interrupt Vector Word */
#define TIMERB1_VECTOR       TIMER0_B1_VECTOR /* Timer0_B7 CC1-6, TB */
#define TIMERB0_VECTOR       TIMER0_B0_VECTOR /* Timer0_B7 CC0 */


/* TBxCTL Control Bits */
#define TBCLGRP1            (0x4000)  /* Timer0_B7 Compare latch load group 1 */
#define TBCLGRP0            (0x2000)  /* Timer0_B7 Compare latch load group 0 */
#define CNTL1               (0x1000)  /* Counter lenght 1 */
#define CNTL0               (0x0800)  /* Counter lenght 0 */
#define TBSSEL1             (0x0200)  /* Clock source 1 */
#define TBSSEL0             (0x0100)  /* Clock source 0 */
#define TBCLR               (0x0004)  /* Timer0_B7 counter clear */
#define TBIE                (0x0002)  /* Timer0_B7 interrupt enable */
#define TBIFG               (0x0001)  /* Timer0_B7 interrupt flag */

/* TBxCTL Control Bits */
#define TBCLR_L             (0x0004)  /* Timer0_B7 counter clear */
#define TBIE_L              (0x0002)  /* Timer0_B7 interrupt enable */
#define TBIFG_L             (0x0001)  /* Timer0_B7 interrupt flag */

/* TBxCTL Control Bits */
#define TBCLGRP1_H          (0x0040)  /* Timer0_B7 Compare latch load group 1 */
#define TBCLGRP0_H          (0x0020)  /* Timer0_B7 Compare latch load group 0 */
#define CNTL1_H             (0x0010)  /* Counter lenght 1 */
#define CNTL0_H             (0x0008)  /* Counter lenght 0 */
#define TBSSEL1_H           (0x0002)  /* Clock source 1 */
#define TBSSEL0_H           (0x0001)  /* Clock source 0 */

#define SHR1                (0x4000)  /* Timer0_B7 Compare latch load group 1 */
#define SHR0                (0x2000)  /* Timer0_B7 Compare latch load group 0 */

#define TBSSEL_0            (0U*0x0100)  /* Clock Source: TBCLK */
#define TBSSEL_1            (1U*0x0100)  /* Clock Source: ACLK  */
#define TBSSEL_2            (2U*0x0100)  /* Clock Source: SMCLK */
#define TBSSEL_3            (3U*0x0100)  /* Clock Source: INCLK */
#define CNTL_0              (0U*0x0800)  /* Counter lenght: 16 bit */
#define CNTL_1              (1U*0x0800)  /* Counter lenght: 12 bit */
#define CNTL_2              (2U*0x0800)  /* Counter lenght: 10 bit */
#define CNTL_3              (3U*0x0800)  /* Counter lenght:  8 bit */
#define SHR_0               (0U*0x2000)  /* Timer0_B7 Group: 0 - individually */
#define SHR_1               (1U*0x2000)  /* Timer0_B7 Group: 1 - 3 groups (1-2, 3-4, 5-6) */
#define SHR_2               (2U*0x2000)  /* Timer0_B7 Group: 2 - 2 groups (1-3, 4-6)*/
#define SHR_3               (3U*0x2000)  /* Timer0_B7 Group: 3 - 1 group (all) */
#define TBCLGRP_0           (0U*0x2000)  /* Timer0_B7 Group: 0 - individually */
#define TBCLGRP_1           (1U*0x2000)  /* Timer0_B7 Group: 1 - 3 groups (1-2, 3-4, 5-6) */
#define TBCLGRP_2           (2U*0x2000)  /* Timer0_B7 Group: 2 - 2 groups (1-3, 4-6)*/
#define TBCLGRP_3           (3U*0x2000)  /* Timer0_B7 Group: 3 - 1 group (all) */
#define TBSSEL__TACLK       (0*0x100) /* Timer0_B7 clock source select: 0 - TACLK */
#define TBSSEL__ACLK        (1*0x100) /* Timer0_B7 clock source select: 1 - ACLK  */
#define TBSSEL__SMCLK       (2*0x100) /* Timer0_B7 clock source select: 2 - SMCLK */
#define TBSSEL__INCLK       (3*0x100) /* Timer0_B7 clock source select: 3 - INCLK */
#define CNTL__16            (0U*0x0800)  /* Counter lenght: 16 bit */
#define CNTL__12            (1U*0x0800)  /* Counter lenght: 12 bit */
#define CNTL__10            (2U*0x0800)  /* Counter lenght: 10 bit */
#define CNTL__8             (3U*0x0800)  /* Counter lenght:  8 bit */

/* Additional Timer B Control Register bits are defined in Timer A */
/* TBxCCTLx Control Bits */
#define CLLD1               (0x0400)  /* Compare latch load source 1 */
#define CLLD0               (0x0200)  /* Compare latch load source 0 */

/* TBxCCTLx Control Bits */

/* TBxCCTLx Control Bits */
#define CLLD1_H             (0x0004)  /* Compare latch load source 1 */
#define CLLD0_H             (0x0002)  /* Compare latch load source 0 */

#define SLSHR1              (0x0400)  /* Compare latch load source 1 */
#define SLSHR0              (0x0200)  /* Compare latch load source 0 */

#define SLSHR_0             (0U*0x0200) /* Compare latch load sourec : 0 - immediate */
#define SLSHR_1             (1U*0x0200) /* Compare latch load sourec : 1 - TBR counts to 0 */
#define SLSHR_2             (2U*0x0200) /* Compare latch load sourec : 2 - up/down */
#define SLSHR_3             (3U*0x0200) /* Compare latch load sourec : 3 - TBR counts to TBCTL0 */

#define CLLD_0              (0U*0x0200) /* Compare latch load sourec : 0 - immediate */
#define CLLD_1              (1U*0x0200) /* Compare latch load sourec : 1 - TBR counts to 0 */
#define CLLD_2              (2U*0x0200) /* Compare latch load sourec : 2 - up/down */
#define CLLD_3              (3U*0x0200) /* Compare latch load sourec : 3 - TBR counts to TBCTL0 */

/* TBxEX0 Control Bits */
#define TBIDEX0             (0x0001)   /* Timer0_B7 Input divider expansion Bit: 0 */
#define TBIDEX1             (0x0002)   /* Timer0_B7 Input divider expansion Bit: 1 */
#define TBIDEX2             (0x0004)   /* Timer0_B7 Input divider expansion Bit: 2 */

/* TBxEX0 Control Bits */
#define TBIDEX0_L           (0x0001)   /* Timer0_B7 Input divider expansion Bit: 0 */
#define TBIDEX1_L           (0x0002)   /* Timer0_B7 Input divider expansion Bit: 1 */
#define TBIDEX2_L           (0x0004)   /* Timer0_B7 Input divider expansion Bit: 2 */

/* TBxEX0 Control Bits */

#define TBIDEX_0            (0U*0x0001) /* Timer0_B7 Input divider expansion : /1 */
#define TBIDEX_1            (1U*0x0001) /* Timer0_B7 Input divider expansion : /2 */
#define TBIDEX_2            (2U*0x0001) /* Timer0_B7 Input divider expansion : /3 */
#define TBIDEX_3            (3U*0x0001) /* Timer0_B7 Input divider expansion : /4 */
#define TBIDEX_4            (4U*0x0001) /* Timer0_B7 Input divider expansion : /5 */
#define TBIDEX_5            (5U*0x0001) /* Timer0_B7 Input divider expansion : /6 */
#define TBIDEX_6            (6U*0x0001) /* Timer0_B7 Input divider expansion : /7 */
#define TBIDEX_7            (7U*0x0001) /* Timer0_B7 Input divider expansion : /8 */
#define TBIDEX__1           (0U*0x0001) /* Timer0_B7 Input divider expansion : /1 */
#define TBIDEX__2           (1U*0x0001) /* Timer0_B7 Input divider expansion : /2 */
#define TBIDEX__3           (2U*0x0001) /* Timer0_B7 Input divider expansion : /3 */
#define TBIDEX__4           (3U*0x0001) /* Timer0_B7 Input divider expansion : /4 */
#define TBIDEX__5           (4U*0x0001) /* Timer0_B7 Input divider expansion : /5 */
#define TBIDEX__6           (5U*0x0001) /* Timer0_B7 Input divider expansion : /6 */
#define TBIDEX__7           (6U*0x0001) /* Timer0_B7 Input divider expansion : /7 */
#define TBIDEX__8           (7U*0x0001) /* Timer0_B7 Input divider expansion : /8 */

/* TB0IV Definitions */
#define TB0IV_NONE          (0x0000)    /* No Interrupt pending */
#define TB0IV_TB1CCR1       (0x0002)    /* TBCCR1_CCIFG */
#define TB0IV_TB1CCR2       (0x0004)    /* TBCCR2_CCIFG */
#define TB0IV_3             (0x0006)    /* Reserved */
#define TB0IV_4             (0x0008)    /* Reserved */
#define TB0IV_5             (0x000A)    /* Reserved */
#define TB0IV_6             (0x000C)    /* Reserved */
#define TB0IV_TB0IFG        (0x000E)    /* TBIFG */


/************************************************************
* USB
************************************************************/
#define __MSP430_HAS_USB__            /* Definition to show that Module is available */

/* ========================================================================= */
/* USB Configuration Registers */
/* ========================================================================= */
#define USBKEYID_             0x0900    /* USB Controller key register */
sfrb(USBKEYID_L, USBKEYID_);
sfrb(USBKEYID_H, USBKEYID_+1);
sfrw(USBKEYID, USBKEYID_);
#define USBCNF_               0x0902    /* USB Module  configuration register */
sfrb(USBCNF_L, USBCNF_);
sfrb(USBCNF_H, USBCNF_+1);
sfrw(USBCNF, USBCNF_);
#define USBPHYCTL_            0x0904    /* USB PHY control register */
sfrb(USBPHYCTL_L, USBPHYCTL_);
sfrb(USBPHYCTL_H, USBPHYCTL_+1);
sfrw(USBPHYCTL, USBPHYCTL_);
#define USBPWRCTL_            0x0908    /* USB Power control register */
sfrb(USBPWRCTL_L, USBPWRCTL_);
sfrb(USBPWRCTL_H, USBPWRCTL_+1);
sfrw(USBPWRCTL, USBPWRCTL_);
#define USBPLLCTL_            0x0910    /* USB PLL control register */
sfrb(USBPLLCTL_L, USBPLLCTL_);
sfrb(USBPLLCTL_H, USBPLLCTL_+1);
sfrw(USBPLLCTL, USBPLLCTL_);
#define USBPLLDIVB_           0x0912    /* USB PLL Clock Divider Buffer control register */
sfrb(USBPLLDIVB_L, USBPLLDIVB_);
sfrb(USBPLLDIVB_H, USBPLLDIVB_+1);
sfrw(USBPLLDIVB, USBPLLDIVB_);
#define USBPLLIR_             0x0914    /* USB PLL Interrupt control register */
sfrb(USBPLLIR_L, USBPLLIR_);
sfrb(USBPLLIR_H, USBPLLIR_+1);
sfrw(USBPLLIR, USBPLLIR_);

#define USBKEYPID      USBKEYID    /* Legacy Definition: USB Controller key register */
#define USBKEY         (0x9628)    /* USB Control Register key */

/* USBCNF Control Bits */
#define USB_EN              (0x0001)  /* USB - Module enable */
#define PUR_EN              (0x0002)  /* USB - PUR pin enable */
#define PUR_IN              (0x0004)  /* USB - PUR pin input value */
#define BLKRDY              (0x0008)  /* USB - Block ready signal for DMA */
#define FNTEN               (0x0010)  /* USB - Frame Number receive Trigger enable for DMA */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBCNF Control Bits */
#define USB_EN_L            (0x0001)  /* USB - Module enable */
#define PUR_EN_L            (0x0002)  /* USB - PUR pin enable */
#define PUR_IN_L            (0x0004)  /* USB - PUR pin input value */
#define BLKRDY_L            (0x0008)  /* USB - Block ready signal for DMA */
#define FNTEN_L             (0x0010)  /* USB - Frame Number receive Trigger enable for DMA */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBCNF Control Bits */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPHYCTL Control Bits */
#define PUOUT0              (0x0001)  /* USB - USB Port Output Signal Bit 0 */
#define PUOUT1              (0x0002)  /* USB - USB Port Output Signal Bit 1 */
#define PUIN0               (0x0004)  /* USB - PU0/DP Input Data */
#define PUIN1               (0x0008)  /* USB - PU1/DM Input Data */
#define PUOM                (0x0010)  /* USB - USB Poort Output Mode */
#define PUDIR               (0x0020)  /* USB - USB Port Output Enable */
#define PUIND               (0x0040)  /* USB - Differntial Input Data */
#define PUSEL               (0x0080)  /* USB - USB Port Function Select */
#define PSEIEN              (0x0100)  /* USB - PHY Single Ended Input enable */
#define PDEIEN              (0x0200)  /* USB - PHY Differential Ended Input enable */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPHYCTL Control Bits */
#define PUOUT0_L            (0x0001)  /* USB - USB Port Output Signal Bit 0 */
#define PUOUT1_L            (0x0002)  /* USB - USB Port Output Signal Bit 1 */
#define PUIN0_L             (0x0004)  /* USB - PU0/DP Input Data */
#define PUIN1_L             (0x0008)  /* USB - PU1/DM Input Data */
#define PUOM_L              (0x0010)  /* USB - USB Poort Output Mode */
#define PUDIR_L             (0x0020)  /* USB - USB Port Output Enable */
#define PUIND_L             (0x0040)  /* USB - Differntial Input Data */
#define PUSEL_L             (0x0080)  /* USB - USB Port Function Select */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPHYCTL Control Bits */
#define PSEIEN_H            (0x0001)  /* USB - PHY Single Ended Input enable */
#define PDEIEN_H            (0x0002)  /* USB - PHY Differential Ended Input enable */
//#define RESERVED            (0x0100)  /* USB -  */
//#define RESERVED            (0x0200)  /* USB -  */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPWRCTL Control Bits */
#define VUOVLIFG            (0x0001)  /* USB - VUSB Overload Interrupt Flag */
#define VBONIFG             (0x0002)  /* USB - VBUS "Coming ON" Interrupt Flag */
#define VBOFFIFG            (0x0004)  /* USB - VBUS "Going OFF" Interrupt Flag */
#define USBBGVBV            (0x0008)  /* USB - USB Bandgap and VBUS valid */
#define USBDETEN            (0x0010)  /* USB - VBUS on/off events enable */
#define OVLAOFF             (0x0020)  /* USB - LDO overload auto off enable */
#define SLDOAON             (0x0040)  /* USB - Secondary LDO auto on enable */
//#define RESERVED            (0x0080)  /* USB -  */
#define VUOVLIE             (0x0100)  /* USB - Overload indication Interrupt Enable */
#define VBONIE              (0x0200)  /* USB - VBUS "Coming ON" Interrupt Enable */
#define VBOFFIE             (0x0400)  /* USB - VBUS "Going OFF" Interrupt Enable */
#define VUSBEN              (0x0800)  /* USB - LDO Enable (3.3V) */
#define SLDOEN              (0x1000)  /* USB - Secondary LDO Enable (1.8V) */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPWRCTL Control Bits */
#define VUOVLIFG_L          (0x0001)  /* USB - VUSB Overload Interrupt Flag */
#define VBONIFG_L           (0x0002)  /* USB - VBUS "Coming ON" Interrupt Flag */
#define VBOFFIFG_L          (0x0004)  /* USB - VBUS "Going OFF" Interrupt Flag */
#define USBBGVBV_L          (0x0008)  /* USB - USB Bandgap and VBUS valid */
#define USBDETEN_L          (0x0010)  /* USB - VBUS on/off events enable */
#define OVLAOFF_L           (0x0020)  /* USB - LDO overload auto off enable */
#define SLDOAON_L           (0x0040)  /* USB - Secondary LDO auto on enable */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPWRCTL Control Bits */
//#define RESERVED            (0x0080)  /* USB -  */
#define VUOVLIE_H           (0x0001)  /* USB - Overload indication Interrupt Enable */
#define VBONIE_H            (0x0002)  /* USB - VBUS "Coming ON" Interrupt Enable */
#define VBOFFIE_H           (0x0004)  /* USB - VBUS "Going OFF" Interrupt Enable */
#define VUSBEN_H            (0x0008)  /* USB - LDO Enable (3.3V) */
#define SLDOEN_H            (0x0010)  /* USB - Secondary LDO Enable (1.8V) */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */


/* USBPLLCTL Control Bits */
//#define RESERVED            (0x0001)  /* USB -  */
//#define RESERVED            (0x0002)  /* USB -  */
//#define RESERVED            (0x0004)  /* USB -  */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
#define UCLKSEL0            (0x0040)  /* USB - Module Clock Select Bit 0 */
#define UCLKSEL1            (0x0080)  /* USB - Module Clock Select Bit 1 */
#define UPLLEN              (0x0100)  /* USB - PLL enable */
#define UPFDEN              (0x0200)  /* USB - Phase Freq. Discriminator enable */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
#define UPCS0               (0x1000)  /* USB - PLL Clock Select Bit 0 */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLCTL Control Bits */
//#define RESERVED            (0x0001)  /* USB -  */
//#define RESERVED            (0x0002)  /* USB -  */
//#define RESERVED            (0x0004)  /* USB -  */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
#define UCLKSEL0_L          (0x0040)  /* USB - Module Clock Select Bit 0 */
#define UCLKSEL1_L          (0x0080)  /* USB - Module Clock Select Bit 1 */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLCTL Control Bits */
//#define RESERVED            (0x0001)  /* USB -  */
//#define RESERVED            (0x0002)  /* USB -  */
//#define RESERVED            (0x0004)  /* USB -  */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
#define UPLLEN_H            (0x0001)  /* USB - PLL enable */
#define UPFDEN_H            (0x0002)  /* USB - Phase Freq. Discriminator enable */
//#define RESERVED            (0x0400)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
#define UPCS0_H             (0x0010)  /* USB - PLL Clock Select Bit 0 */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

#define UCLKSEL_0           (0x0000)  /* USB - Module Clock Select: 0 */
#define UCLKSEL_1           (0x0040)  /* USB - Module Clock Select: 1 */
#define UCLKSEL_2           (0x0080)  /* USB - Module Clock Select: 2 */
#define UCLKSEL_3           (0x00C0)  /* USB - Module Clock Select: 3 (Reserved) */

#define UCLKSEL__PLLCLK     (0x0000)  /* USB - Module Clock Select: PLLCLK */
#define UCLKSEL__XT1CLK     (0x0040)  /* USB - Module Clock Select: XT1CLK */
#define UCLKSEL__XT2CLK     (0x0080)  /* USB - Module Clock Select: XT2CLK */

/* USBPLLDIVB Control Bits */
#define UPMB0               (0x0001)  /* USB - PLL feedback divider buffer Bit 0 */
#define UPMB1               (0x0002)  /* USB - PLL feedback divider buffer Bit 1 */
#define UPMB2               (0x0004)  /* USB - PLL feedback divider buffer Bit 2 */
#define UPMB3               (0x0008)  /* USB - PLL feedback divider buffer Bit 3 */
#define UPMB4               (0x0010)  /* USB - PLL feedback divider buffer Bit 4 */
#define UPMB5               (0x0020)  /* USB - PLL feedback divider buffer Bit 5 */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
#define UPQB0               (0x0100)  /* USB - PLL prescale divider buffer Bit 0 */
#define UPQB1               (0x0200)  /* USB - PLL prescale divider buffer Bit 1 */
#define UPQB2               (0x0400)  /* USB - PLL prescale divider buffer Bit 2 */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLDIVB Control Bits */
#define UPMB0_L             (0x0001)  /* USB - PLL feedback divider buffer Bit 0 */
#define UPMB1_L             (0x0002)  /* USB - PLL feedback divider buffer Bit 1 */
#define UPMB2_L             (0x0004)  /* USB - PLL feedback divider buffer Bit 2 */
#define UPMB3_L             (0x0008)  /* USB - PLL feedback divider buffer Bit 3 */
#define UPMB4_L             (0x0010)  /* USB - PLL feedback divider buffer Bit 4 */
#define UPMB5_L             (0x0020)  /* USB - PLL feedback divider buffer Bit 5 */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLDIVB Control Bits */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
#define UPQB0_H             (0x0001)  /* USB - PLL prescale divider buffer Bit 0 */
#define UPQB1_H             (0x0002)  /* USB - PLL prescale divider buffer Bit 1 */
#define UPQB2_H             (0x0004)  /* USB - PLL prescale divider buffer Bit 2 */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

#define USBPLL_SETCLK_1_5      (UPMB0*31 | UPQB0*0)  /* USB - PLL Set for 1.5 MHz input clock */
#define USBPLL_SETCLK_1_6      (UPMB0*29 | UPQB0*0)  /* USB - PLL Set for 1.6 MHz input clock */
#define USBPLL_SETCLK_1_7778   (UPMB0*26 | UPQB0*0)  /* USB - PLL Set for 1.7778 MHz input clock */
#define USBPLL_SETCLK_1_8432   (UPMB0*25 | UPQB0*0)  /* USB - PLL Set for 1.8432 MHz input clock */
#define USBPLL_SETCLK_1_8461   (UPMB0*25 | UPQB0*0)  /* USB - PLL Set for 1.8461 MHz input clock */
#define USBPLL_SETCLK_1_92     (UPMB0*24 | UPQB0*0)  /* USB - PLL Set for 1.92 MHz input clock */
#define USBPLL_SETCLK_2_0      (UPMB0*23 | UPQB0*0)  /* USB - PLL Set for 2.0 MHz input clock */
#define USBPLL_SETCLK_2_4      (UPMB0*19 | UPQB0*0)  /* USB - PLL Set for 2.4 MHz input clock */
#define USBPLL_SETCLK_2_6667   (UPMB0*17 | UPQB0*0)  /* USB - PLL Set for 2.6667 MHz input clock */
#define USBPLL_SETCLK_3_0      (UPMB0*15 | UPQB0*0)  /* USB - PLL Set for 3.0 MHz input clock */
#define USBPLL_SETCLK_3_2      (UPMB0*29 | UPQB0*1)  /* USB - PLL Set for 3.2 MHz input clock */
#define USBPLL_SETCLK_3_5556   (UPMB0*26 | UPQB0*1)  /* USB - PLL Set for 3.5556 MHz input clock */
#define USBPLL_SETCLK_3_579545 (UPMB0*26 | UPQB0*1)  /* USB - PLL Set for 3.579546 MHz input clock */
#define USBPLL_SETCLK_3_84     (UPMB0*24 | UPQB0*1)  /* USB - PLL Set for 3.84 MHz input clock */
#define USBPLL_SETCLK_4_0      (UPMB0*23 | UPQB0*1)  /* USB - PLL Set for 4.0 MHz input clock */
#define USBPLL_SETCLK_4_1739   (UPMB0*22 | UPQB0*1)  /* USB - PLL Set for 4.1739 MHz input clock */
#define USBPLL_SETCLK_4_1943   (UPMB0*22 | UPQB0*1)  /* USB - PLL Set for 4.1943 MHz input clock */
#define USBPLL_SETCLK_4_332    (UPMB0*21 | UPQB0*1)  /* USB - PLL Set for 4.332 MHz input clock */
#define USBPLL_SETCLK_4_3636   (UPMB0*21 | UPQB0*1)  /* USB - PLL Set for 4.3636 MHz input clock */
#define USBPLL_SETCLK_4_5      (UPMB0*31 | UPQB0*2)  /* USB - PLL Set for 4.5 MHz input clock */
#define USBPLL_SETCLK_4_8      (UPMB0*19 | UPQB0*1)  /* USB - PLL Set for 4.8 MHz input clock */
#define USBPLL_SETCLK_5_33     (UPMB0*17 | UPQB0*1)  /* USB - PLL Set for 5.33 MHz input clock */
#define USBPLL_SETCLK_5_76     (UPMB0*24 | UPQB0*2)  /* USB - PLL Set for 5.76 MHz input clock */
#define USBPLL_SETCLK_6_0      (UPMB0*23 | UPQB0*2)  /* USB - PLL Set for 6.0 MHz input clock */
#define USBPLL_SETCLK_6_4      (UPMB0*29 | UPQB0*3)  /* USB - PLL Set for 6.4 MHz input clock */
#define USBPLL_SETCLK_7_2      (UPMB0*19 | UPQB0*2)  /* USB - PLL Set for 7.2 MHz input clock */
#define USBPLL_SETCLK_7_68     (UPMB0*24 | UPQB0*3)  /* USB - PLL Set for 7.68 MHz input clock */
#define USBPLL_SETCLK_8_0      (UPMB0*17 | UPQB0*2)  /* USB - PLL Set for 8.0 MHz input clock */
#define USBPLL_SETCLK_9_0      (UPMB0*15 | UPQB0*2)  /* USB - PLL Set for 9.0 MHz input clock */
#define USBPLL_SETCLK_9_6      (UPMB0*19 | UPQB0*3)  /* USB - PLL Set for 9.6 MHz input clock */
#define USBPLL_SETCLK_10_66    (UPMB0*17 | UPQB0*3)  /* USB - PLL Set for 10.66 MHz input clock */
#define USBPLL_SETCLK_12_0     (UPMB0*15 | UPQB0*3)  /* USB - PLL Set for 12.0 MHz input clock */
#define USBPLL_SETCLK_12_8     (UPMB0*29 | UPQB0*5)  /* USB - PLL Set for 12.8 MHz input clock */
#define USBPLL_SETCLK_14_4     (UPMB0*19 | UPQB0*4)  /* USB - PLL Set for 14.4 MHz input clock */
#define USBPLL_SETCLK_16_0     (UPMB0*17 | UPQB0*4)  /* USB - PLL Set for 16.0 MHz input clock */
#define USBPLL_SETCLK_16_9344  (UPMB0*16 | UPQB0*4)  /* USB - PLL Set for 16.9344 MHz input clock */
#define USBPLL_SETCLK_16_94118 (UPMB0*16 | UPQB0*4)  /* USB - PLL Set for 16.94118 MHz input clock */
#define USBPLL_SETCLK_18_0     (UPMB0*15 | UPQB0*4)  /* USB - PLL Set for 18.0 MHz input clock */
#define USBPLL_SETCLK_19_2     (UPMB0*19 | UPQB0*5)  /* USB - PLL Set for 19.2 MHz input clock */
#define USBPLL_SETCLK_24_0     (UPMB0*15 | UPQB0*5)  /* USB - PLL Set for 24.0 MHz input clock */
#define USBPLL_SETCLK_25_6     (UPMB0*29 | UPQB0*7)  /* USB - PLL Set for 25.6 MHz input clock */
#define USBPLL_SETCLK_26_0     (UPMB0*23 | UPQB0*6)  /* USB - PLL Set for 26.0 MHz input clock */
#define USBPLL_SETCLK_32_0     (UPMB0*23 | UPQB0*7)  /* USB - PLL Set for 32.0 MHz input clock */


/* USBPLLIR Control Bits */
#define USBOOLIFG           (0x0001)  /* USB - PLL out of lock Interrupt Flag */
#define USBLOSIFG           (0x0002)  /* USB - PLL loss of signal Interrupt Flag */
#define USBOORIFG           (0x0004)  /* USB - PLL out of range Interrupt Flag */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
#define USBOOLIE            (0x0100)  /* USB - PLL out of lock Interrupt enable */
#define USBLOSIE            (0x0200)  /* USB - PLL loss of signal Interrupt enable */
#define USBOORIE            (0x0400)  /* USB - PLL out of range Interrupt enable */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLIR Control Bits */
#define USBOOLIFG_L         (0x0001)  /* USB - PLL out of lock Interrupt Flag */
#define USBLOSIFG_L         (0x0002)  /* USB - PLL loss of signal Interrupt Flag */
#define USBOORIFG_L         (0x0004)  /* USB - PLL out of range Interrupt Flag */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */

/* USBPLLIR Control Bits */
//#define RESERVED            (0x0008)  /* USB -  */
//#define RESERVED            (0x0010)  /* USB -  */
//#define RESERVED            (0x0020)  /* USB -  */
//#define RESERVED            (0x0040)  /* USB -  */
//#define RESERVED            (0x0080)  /* USB -  */
#define USBOOLIE_H          (0x0001)  /* USB - PLL out of lock Interrupt enable */
#define USBLOSIE_H          (0x0002)  /* USB - PLL loss of signal Interrupt enable */
#define USBOORIE_H          (0x0004)  /* USB - PLL out of range Interrupt enable */
//#define RESERVED            (0x0800)  /* USB -  */
//#define RESERVED            (0x1000)  /* USB -  */
//#define RESERVED            (0x2000)  /* USB -  */
//#define RESERVED            (0x4000)  /* USB -  */
//#define RESERVED            (0x8000)  /* USB -  */



/* ========================================================================= */
/* USB Control Registers */
/* ========================================================================= */
#define USBIEPCNF_0_          0x0920    /* USB Input endpoint_0: Configuration */
sfrb(USBIEPCNF_0, USBIEPCNF_0_);
#define USBIEPCNT_0_          0x0921    /* USB Input endpoint_0: Byte Count */
sfrb(USBIEPCNT_0, USBIEPCNT_0_);
#define USBOEPCNF_0_          0x0922    /* USB Output endpoint_0: Configuration */
sfrb(USBOEPCNF_0, USBOEPCNF_0_);
#define USBOEPCNT_0_          0x0923    /* USB Output endpoint_0: byte count */
sfrb(USBOEPCNT_0, USBOEPCNT_0_);
#define USBIEPIE_             0x092E    /* USB Input endpoint interrupt enable flags */
sfrb(USBIEPIE, USBIEPIE_);
#define USBOEPIE_             0x092F    /* USB Output endpoint interrupt enable flags */
sfrb(USBOEPIE, USBOEPIE_);
#define USBIEPIFG_            0x0930    /* USB Input endpoint interrupt flags */
sfrb(USBIEPIFG, USBIEPIFG_);
#define USBOEPIFG_            0x0931    /* USB Output endpoint interrupt flags */
sfrb(USBOEPIFG, USBOEPIFG_);
#define USBVECINT_            0x0932    /* USB Vector interrupt register */
sfrb(USBVECINT_L, USBVECINT_);
sfrb(USBVECINT_H, USBVECINT_+1);
sfrw(USBVECINT, USBVECINT_);
#define USBMAINT_             0x0936    /* USB maintenance register */
sfrb(USBMAINT_L, USBMAINT_);
sfrb(USBMAINT_H, USBMAINT_+1);
sfrw(USBMAINT, USBMAINT_);
#define USBTSREG_             0x0938    /* USB Time Stamp register */
sfrb(USBTSREG_L, USBTSREG_);
sfrb(USBTSREG_H, USBTSREG_+1);
sfrw(USBTSREG, USBTSREG_);
#define USBFN_                0x093A    /* USB Frame number */
sfrb(USBFN_L, USBFN_);
sfrb(USBFN_H, USBFN_+1);
sfrw(USBFN, USBFN_);
#define USBCTL_               0x093C    /* USB control register */
sfrb(USBCTL, USBCTL_);
#define USBIE_                0x093D    /* USB interrupt enable register */
sfrb(USBIE, USBIE_);
#define USBIFG_               0x093E    /* USB interrupt flag register */
sfrb(USBIFG, USBIFG_);
#define USBFUNADR_            0x093F    /* USB Function address register */
sfrb(USBFUNADR, USBFUNADR_);

/* USBIEPCNF_0 Control Bits */
/* USBOEPCNF_0 Control Bits */
//#define RESERVED       (0x0001)  /* USB -  */
//#define RESERVED       (0x0001)  /* USB -  */
#define USBIIE         (0x0004)  /* USB - Transaction Interrupt indication enable */
#define STALL          (0x0008)  /* USB - Stall Condition */
//#define RESERVED       (0x0010)  /* USB -  */
#define TOGGLE         (0x0020)  /* USB - Toggle Bit */
//#define RESERVED       (0x0040)  /* USB -  */
#define UBME           (0x0080)  /* USB - UBM In-Endpoint Enable */

/* USBIEPBCNT_0 Control Bits */
/* USBOEPBCNT_0 Control Bits */
#define CNT0           (0x0001)  /* USB - Byte Count Bit 0 */
#define CNT1           (0x0001)  /* USB - Byte Count Bit 1 */
#define CNT2           (0x0004)  /* USB - Byte Count Bit 2 */
#define CNT3           (0x0008)  /* USB - Byte Count Bit 3 */
//#define RESERVED       (0x0010)  /* USB -  */
//#define RESERVED       (0x0020)  /* USB -  */
//#define RESERVED       (0x0040)  /* USB -  */
#define NAK            (0x0080)  /* USB - No Acknowledge Status Bit */


/* USBMAINT Control Bits */
#define UTIFG          (0x0001)  /* USB - Timer Interrupt Flag */
#define UTIE           (0x0002)  /* USB - Timer Interrupt Enable */
//#define RESERVED       (0x0004)  /* USB -  */
//#define RESERVED       (0x0008)  /* USB -  */
//#define RESERVED       (0x0010)  /* USB -  */
//#define RESERVED       (0x0020)  /* USB -  */
//#define RESERVED       (0x0040)  /* USB -  */
//#define RESERVED       (0x0080)  /* USB -  */
#define TSGEN          (0x0100)  /* USB - Time Stamp Generator Enable */
#define TSESEL0        (0x0200)  /* USB - Time Stamp Event Select Bit 0 */
#define TSESEL1        (0x0400)  /* USB - Time Stamp Event Select Bit 1 */
#define TSE3           (0x0800)  /* USB - Time Stamp Event #3 Bit */
//#define RESERVED       (0x1000)  /* USB -  */
#define UTSEL0         (0x2000)  /* USB - Timer Select Bit 0 */
#define UTSEL1         (0x4000)  /* USB - Timer Select Bit 1 */
#define UTSEL2         (0x8000)  /* USB - Timer Select Bit 2 */

/* USBMAINT Control Bits */
#define UTIFG_L             (0x0001)  /* USB - Timer Interrupt Flag */
#define UTIE_L              (0x0002)  /* USB - Timer Interrupt Enable */
//#define RESERVED       (0x0004)  /* USB -  */
//#define RESERVED       (0x0008)  /* USB -  */
//#define RESERVED       (0x0010)  /* USB -  */
//#define RESERVED       (0x0020)  /* USB -  */
//#define RESERVED       (0x0040)  /* USB -  */
//#define RESERVED       (0x0080)  /* USB -  */
//#define RESERVED       (0x1000)  /* USB -  */

/* USBMAINT Control Bits */
//#define RESERVED       (0x0004)  /* USB -  */
//#define RESERVED       (0x0008)  /* USB -  */
//#define RESERVED       (0x0010)  /* USB -  */
//#define RESERVED       (0x0020)  /* USB -  */
//#define RESERVED       (0x0040)  /* USB -  */
//#define RESERVED       (0x0080)  /* USB -  */
#define TSGEN_H             (0x0001)  /* USB - Time Stamp Generator Enable */
#define TSESEL0_H           (0x0002)  /* USB - Time Stamp Event Select Bit 0 */
#define TSESEL1_H           (0x0004)  /* USB - Time Stamp Event Select Bit 1 */
#define TSE3_H              (0x0008)  /* USB - Time Stamp Event #3 Bit */
//#define RESERVED       (0x1000)  /* USB -  */
#define UTSEL0_H            (0x0020)  /* USB - Timer Select Bit 0 */
#define UTSEL1_H            (0x0040)  /* USB - Timer Select Bit 1 */
#define UTSEL2_H            (0x0080)  /* USB - Timer Select Bit 2 */

#define TSESEL_0       (0x0000)  /* USB - Time Stamp Event Select: 0 */
#define TSESEL_1       (0x0200)  /* USB - Time Stamp Event Select: 1 */
#define TSESEL_2       (0x0400)  /* USB - Time Stamp Event Select: 2 */
#define TSESEL_3       (0x0600)  /* USB - Time Stamp Event Select: 3 */

#define UTSEL_0        (0x0000)  /* USB - Timer Select: 0 */
#define UTSEL_1        (0x2000)  /* USB - Timer Select: 1 */
#define UTSEL_2        (0x4000)  /* USB - Timer Select: 2 */
#define UTSEL_3        (0x6000)  /* USB - Timer Select: 3 */
#define UTSEL_4        (0x8000)  /* USB - Timer Select: 4 */
#define UTSEL_5        (0xA000)  /* USB - Timer Select: 5 */
#define UTSEL_6        (0xC000)  /* USB - Timer Select: 6 */
#define UTSEL_7        (0xE000)  /* USB - Timer Select: 7 */

/* USBCTL Control Bits */
#define DIR            (0x0001)  /* USB - Data Response Bit */
//#define RESERVED       (0x0002)  /* USB -  */
//#define RESERVED       (0x0004)  /* USB -  */
//#define RESERVED       (0x0008)  /* USB -  */
#define FRSTE          (0x0010)  /* USB - Function Reset Connection Enable */
#define RWUP           (0x0020)  /* USB - Device Remote Wakeup Request */
#define FEN            (0x0040)  /* USB - Function Enable Bit */
//#define RESERVED       (0x0080)  /* USB -  */

/* USBIE Control Bits */
#define STPOWIE        (0x0001)  /* USB - Setup Overwrite Interrupt Enable */
//#define RESERVED       (0x0002)  /* USB -  */
#define SETUPIE        (0x0004)  /* USB - Setup Interrupt Enable */
//#define RESERVED       (0x0008)  /* USB -  */
//#define RESERVED       (0x0010)  /* USB -  */
#define RESRIE         (0x0020)  /* USB - Function Resume Request Interrupt Enable */
#define SUSRIE         (0x0040)  /* USB - Function Suspend Request Interrupt Enable */
#define RSTRIE         (0x0080)  /* USB - Function Reset Request Interrupt Enable */

/* USBIFG Control Bits */
#define STPOWIFG       (0x0001)  /* USB - Setup Overwrite Interrupt Flag */
//#define RESERVED       (0x0002)  /* USB -  */
#define SETUPIFG       (0x0004)  /* USB - Setup Interrupt Flag */
//#define RESERVED       (0x0008)  /* USB -  */
//#define RESERVED       (0x0010)  /* USB -  */
#define RESRIFG        (0x0020)  /* USB - Function Resume Request Interrupt Flag */
#define SUSRIFG        (0x0040)  /* USB - Function Suspend Request Interrupt Flag */
#define RSTRIFG        (0x0080)  /* USB - Function Reset Request Interrupt Flag */

//values of USBVECINT when USB-interrupt occured
#define     USBVECINT_NONE                     0x00
#define     USBVECINT_PWR_DROP                 0x02
#define     USBVECINT_PLL_LOCK                 0x04
#define     USBVECINT_PLL_SIGNAL               0x06
#define     USBVECINT_PLL_RANGE                0x08
#define     USBVECINT_PWR_VBUSOn               0x0A
#define     USBVECINT_PWR_VBUSOff              0x0C
#define     USBVECINT_USB_TIMESTAMP            0x10
#define     USBVECINT_INPUT_ENDPOINT0          0x12
#define     USBVECINT_OUTPUT_ENDPOINT0         0x14
#define     USBVECINT_RSTR                     0x16
#define     USBVECINT_SUSR                     0x18
#define     USBVECINT_RESR                     0x1A
#define     USBVECINT_SETUP_PACKET_RECEIVED    0x20
#define     USBVECINT_STPOW_PACKET_RECEIVED    0x22
#define     USBVECINT_INPUT_ENDPOINT1          0x24
#define     USBVECINT_INPUT_ENDPOINT2          0x26
#define     USBVECINT_INPUT_ENDPOINT3          0x28
#define     USBVECINT_INPUT_ENDPOINT4          0x2A
#define     USBVECINT_INPUT_ENDPOINT5          0x2C
#define     USBVECINT_INPUT_ENDPOINT6          0x2E
#define     USBVECINT_INPUT_ENDPOINT7          0x30
#define     USBVECINT_OUTPUT_ENDPOINT1         0x32
#define     USBVECINT_OUTPUT_ENDPOINT2         0x34
#define     USBVECINT_OUTPUT_ENDPOINT3         0x36
#define     USBVECINT_OUTPUT_ENDPOINT4         0x38
#define     USBVECINT_OUTPUT_ENDPOINT5         0x3A
#define     USBVECINT_OUTPUT_ENDPOINT6         0x3C
#define     USBVECINT_OUTPUT_ENDPOINT7         0x3E

                                                           
/* ========================================================================= */
/* USB Operation Registers */
/* ========================================================================= */

#define USBIEPSIZXY_7_        0x23FF    /* Input Endpoint_7: X/Y-buffer size  */
sfrb(USBIEPSIZXY_7, USBIEPSIZXY_7_);
#define USBIEPBCTY_7_         0x23FE    /* Input Endpoint_7: Y-byte count  */
sfrb(USBIEPBCTY_7, USBIEPBCTY_7_);
#define USBIEPBBAY_7_         0x23FD    /* Input Endpoint_7: Y-buffer base addr.  */
sfrb(USBIEPBBAY_7, USBIEPBBAY_7_);
//sfrb    Spare    (0x23FC)   /* Not used  */
//sfrb    Spare    (0x23FB)   /* Not used  */
#define USBIEPBCTX_7_         0x23FA    /* Input Endpoint_7: X-byte count  */
sfrb(USBIEPBCTX_7, USBIEPBCTX_7_);
#define USBIEPBBAX_7_         0x23F9    /* Input Endpoint_7: X-buffer base addr. */
sfrb(USBIEPBBAX_7, USBIEPBBAX_7_);
#define USBIEPCNF_7_          0x23F8    /* Input Endpoint_7: Configuration  */
sfrb(USBIEPCNF_7, USBIEPCNF_7_);
#define USBIEPSIZXY_6_        0x23F7    /* Input Endpoint_6: X/Y-buffer size  */
sfrb(USBIEPSIZXY_6, USBIEPSIZXY_6_);
#define USBIEPBCTY_6_         0x23F6    /* Input Endpoint_6: Y-byte count */
sfrb(USBIEPBCTY_6, USBIEPBCTY_6_);
#define USBIEPBBAY_6_         0x23F5    /* Input Endpoint_6: Y-buffer base addr. */
sfrb(USBIEPBBAY_6, USBIEPBBAY_6_);
//sfrb    Spare    (0x23F4)   /* Not used  */
//sfrb    Spare    (0x23F3)   /* Not used  */
#define USBIEPBCTX_6_         0x23F2    /* Input Endpoint_6: X-byte count */
sfrb(USBIEPBCTX_6, USBIEPBCTX_6_);
#define USBIEPBBAX_6_         0x23F1    /* Input Endpoint_6: X-buffer base addr. */
sfrb(USBIEPBBAX_6, USBIEPBBAX_6_);
#define USBIEPCNF_6_          0x23F0    /* Input Endpoint_6: Configuration */
sfrb(USBIEPCNF_6, USBIEPCNF_6_);
#define USBIEPSIZXY_5_        0x23EF    /* Input Endpoint_5: X/Y-buffer size */
sfrb(USBIEPSIZXY_5, USBIEPSIZXY_5_);
#define USBIEPBCTY_5_         0x23EE    /* Input Endpoint_5: Y-byte count */
sfrb(USBIEPBCTY_5, USBIEPBCTY_5_);
#define USBIEPBBAY_5_         0x23ED    /* Input Endpoint_5: Y-buffer base addr. */
sfrb(USBIEPBBAY_5, USBIEPBBAY_5_);
//sfrb    Spare    (0x23EC)   /* Not used */
//sfrb    Spare    (0x23EB)   /* Not used */
#define USBIEPBCTX_5_         0x23EA    /* Input Endpoint_5: X-byte count */
sfrb(USBIEPBCTX_5, USBIEPBCTX_5_);
#define USBIEPBBAX_5_         0x23E9    /* Input Endpoint_5: X-buffer base addr. */
sfrb(USBIEPBBAX_5, USBIEPBBAX_5_);
#define USBIEPCNF_5_          0x23E8    /* Input Endpoint_5: Configuration */
sfrb(USBIEPCNF_5, USBIEPCNF_5_);
#define USBIEPSIZXY_4_        0x23E7    /* Input Endpoint_4: X/Y-buffer size */
sfrb(USBIEPSIZXY_4, USBIEPSIZXY_4_);
#define USBIEPBCTY_4_         0x23E6    /* Input Endpoint_4: Y-byte count */
sfrb(USBIEPBCTY_4, USBIEPBCTY_4_);
#define USBIEPBBAY_4_         0x23E5    /* Input Endpoint_4: Y-buffer base addr. */
sfrb(USBIEPBBAY_4, USBIEPBBAY_4_);
//sfrb    Spare    (0x23E4)   /* Not used */
//sfrb    Spare    (0x23E3)   /* Not used */
#define USBIEPBCTX_4_         0x23E2    /* Input Endpoint_4: X-byte count */
sfrb(USBIEPBCTX_4, USBIEPBCTX_4_);
#define USBIEPBBAX_4_         0x23E1    /* Input Endpoint_4: X-buffer base addr. */
sfrb(USBIEPBBAX_4, USBIEPBBAX_4_);
#define USBIEPCNF_4_          0x23E0    /* Input Endpoint_4: Configuration */
sfrb(USBIEPCNF_4, USBIEPCNF_4_);
#define USBIEPSIZXY_3_        0x23DF    /* Input Endpoint_3: X/Y-buffer size */
sfrb(USBIEPSIZXY_3, USBIEPSIZXY_3_);
#define USBIEPBCTY_3_         0x23DE    /* Input Endpoint_3: Y-byte count */
sfrb(USBIEPBCTY_3, USBIEPBCTY_3_);
#define USBIEPBBAY_3_         0x23DD    /* Input Endpoint_3: Y-buffer base addr. */
sfrb(USBIEPBBAY_3, USBIEPBBAY_3_);
//sfrb    Spare    (0x23DC)   /* Not used */
//sfrb    Spare    (0x23DB)   /* Not used */
#define USBIEPBCTX_3_         0x23DA    /* Input Endpoint_3: X-byte count */
sfrb(USBIEPBCTX_3, USBIEPBCTX_3_);
#define USBIEPBBAX_3_         0x23D9    /* Input Endpoint_3: X-buffer base addr. */
sfrb(USBIEPBBAX_3, USBIEPBBAX_3_);
#define USBIEPCNF_3_          0x23D8    /* Input Endpoint_3: Configuration */
sfrb(USBIEPCNF_3, USBIEPCNF_3_);
#define USBIEPSIZXY_2_        0x23D7    /* Input Endpoint_2: X/Y-buffer size */
sfrb(USBIEPSIZXY_2, USBIEPSIZXY_2_);
#define USBIEPBCTY_2_         0x23D6    /* Input Endpoint_2: Y-byte count */
sfrb(USBIEPBCTY_2, USBIEPBCTY_2_);
#define USBIEPBBAY_2_         0x23D5    /* Input Endpoint_2: Y-buffer base addr. */
sfrb(USBIEPBBAY_2, USBIEPBBAY_2_);
//sfrb    Spare    (0x23D4)   /* Not used */
//sfrb    Spare    (0x23D3)   /* Not used */
#define USBIEPBCTX_2_         0x23D2    /* Input Endpoint_2: X-byte count */
sfrb(USBIEPBCTX_2, USBIEPBCTX_2_);
#define USBIEPBBAX_2_         0x23D1    /* Input Endpoint_2: X-buffer base addr. */
sfrb(USBIEPBBAX_2, USBIEPBBAX_2_);
#define USBIEPCNF_2_          0x23D0    /* Input Endpoint_2: Configuration */
sfrb(USBIEPCNF_2, USBIEPCNF_2_);
#define USBIEPSIZXY_1_        0x23CF    /* Input Endpoint_1: X/Y-buffer size */
sfrb(USBIEPSIZXY_1, USBIEPSIZXY_1_);
#define USBIEPBCTY_1_         0x23CE    /* Input Endpoint_1: Y-byte count */
sfrb(USBIEPBCTY_1, USBIEPBCTY_1_);
#define USBIEPBBAY_1_         0x23CD    /* Input Endpoint_1: Y-buffer base addr. */
sfrb(USBIEPBBAY_1, USBIEPBBAY_1_);
//sfrb    Spare    (0x23CC)   /* Not used */
//sfrb    Spare    (0x23CB)   /* Not used */
#define USBIEPBCTX_1_         0x23CA    /* Input Endpoint_1: X-byte count */
sfrb(USBIEPBCTX_1, USBIEPBCTX_1_);
#define USBIEPBBAX_1_         0x23C9    /* Input Endpoint_1: X-buffer base addr. */
sfrb(USBIEPBBAX_1, USBIEPBBAX_1_);
#define USBIEPCNF_1_          0x23C8    /* Input Endpoint_1: Configuration */
sfrb(USBIEPCNF_1, USBIEPCNF_1_);
//sfrb       (0x23C7)   0x0000 */
//sfrb     RESERVED      (0x1C00)    /* */
//sfrb       (0x23C0)   0x0000 */
#define USBOEPSIZXY_7_        0x23BF    /* Output Endpoint_7: X/Y-buffer size */
sfrb(USBOEPSIZXY_7, USBOEPSIZXY_7_);
#define USBOEPBCTY_7_         0x23BE    /* Output Endpoint_7: Y-byte count */
sfrb(USBOEPBCTY_7, USBOEPBCTY_7_);
#define USBOEPBBAY_7_         0x23BD    /* Output Endpoint_7: Y-buffer base addr. */
sfrb(USBOEPBBAY_7, USBOEPBBAY_7_);
//sfrb    Spare    (0x23BC)   /* Not used */
//sfrb    Spare    (0x23BB)   /* Not used */
#define USBOEPBCTX_7_         0x23BA    /* Output Endpoint_7: X-byte count */
sfrb(USBOEPBCTX_7, USBOEPBCTX_7_);
#define USBOEPBBAX_7_         0x23B9    /* Output Endpoint_7: X-buffer base addr. */
sfrb(USBOEPBBAX_7, USBOEPBBAX_7_);
#define USBOEPCNF_7_          0x23B8    /* Output Endpoint_7: Configuration */
sfrb(USBOEPCNF_7, USBOEPCNF_7_);
#define USBOEPSIZXY_6_        0x23B7    /* Output Endpoint_6: X/Y-buffer size */
sfrb(USBOEPSIZXY_6, USBOEPSIZXY_6_);
#define USBOEPBCTY_6_         0x23B6    /* Output Endpoint_6: Y-byte count */
sfrb(USBOEPBCTY_6, USBOEPBCTY_6_);
#define USBOEPBBAY_6_         0x23B5    /* Output Endpoint_6: Y-buffer base addr. */
sfrb(USBOEPBBAY_6, USBOEPBBAY_6_);
//sfrb    Spare    (0x23B4)   /* Not used */
//sfrb    Spare    (0x23B3)   /* Not used */
#define USBOEPBCTX_6_         0x23B2    /* Output Endpoint_6: X-byte count */
sfrb(USBOEPBCTX_6, USBOEPBCTX_6_);
#define USBOEPBBAX_6_         0x23B1    /* Output Endpoint_6: X-buffer base addr. */
sfrb(USBOEPBBAX_6, USBOEPBBAX_6_);
#define USBOEPCNF_6_          0x23B0    /* Output Endpoint_6: Configuration */
sfrb(USBOEPCNF_6, USBOEPCNF_6_);
#define USBOEPSIZXY_5_        0x23AF    /* Output Endpoint_5: X/Y-buffer size */
sfrb(USBOEPSIZXY_5, USBOEPSIZXY_5_);
#define USBOEPBCTY_5_         0x23AE    /* Output Endpoint_5: Y-byte count */
sfrb(USBOEPBCTY_5, USBOEPBCTY_5_);
#define USBOEPBBAY_5_         0x23AD    /* Output Endpoint_5: Y-buffer base addr. */
sfrb(USBOEPBBAY_5, USBOEPBBAY_5_);
//sfrb    Spare    (0x23AC)   /* Not used */
//sfrb    Spare    (0x23AB)   /* Not used */
#define USBOEPBCTX_5_         0x23AA    /* Output Endpoint_5: X-byte count */
sfrb(USBOEPBCTX_5, USBOEPBCTX_5_);
#define USBOEPBBAX_5_         0x23A9    /* Output Endpoint_5: X-buffer base addr. */
sfrb(USBOEPBBAX_5, USBOEPBBAX_5_);
#define USBOEPCNF_5_          0x23A8    /* Output Endpoint_5: Configuration */
sfrb(USBOEPCNF_5, USBOEPCNF_5_);
#define USBOEPSIZXY_4_        0x23A7    /* Output Endpoint_4: X/Y-buffer size */
sfrb(USBOEPSIZXY_4, USBOEPSIZXY_4_);
#define USBOEPBCTY_4_         0x23A6    /* Output Endpoint_4: Y-byte count */
sfrb(USBOEPBCTY_4, USBOEPBCTY_4_);
#define USBOEPBBAY_4_         0x23A5    /* Output Endpoint_4: Y-buffer base addr. */
sfrb(USBOEPBBAY_4, USBOEPBBAY_4_);
//sfrb    Spare    (0x23A4)   /* Not used */
//sfrb    Spare    (0x23A3)   /* Not used */
#define USBOEPBCTX_4_         0x23A2    /* Output Endpoint_4: X-byte count */
sfrb(USBOEPBCTX_4, USBOEPBCTX_4_);
#define USBOEPBBAX_4_         0x23A1    /* Output Endpoint_4: X-buffer base addr. */
sfrb(USBOEPBBAX_4, USBOEPBBAX_4_);
#define USBOEPCNF_4_          0x23A0    /* Output Endpoint_4: Configuration */
sfrb(USBOEPCNF_4, USBOEPCNF_4_);
#define USBOEPSIZXY_3_        0x239F    /* Output Endpoint_3: X/Y-buffer size */
sfrb(USBOEPSIZXY_3, USBOEPSIZXY_3_);
#define USBOEPBCTY_3_         0x239E    /* Output Endpoint_3: Y-byte count */
sfrb(USBOEPBCTY_3, USBOEPBCTY_3_);
#define USBOEPBBAY_3_         0x239D    /* Output Endpoint_3: Y-buffer base addr. */
sfrb(USBOEPBBAY_3, USBOEPBBAY_3_);
//sfrb    Spare    (0x239C)   /* Not used */
//sfrb    Spare    (0x239B)   /* Not used */
#define USBOEPBCTX_3_         0x239A    /* Output Endpoint_3: X-byte count */
sfrb(USBOEPBCTX_3, USBOEPBCTX_3_);
#define USBOEPBBAX_3_         0x2399    /* Output Endpoint_3: X-buffer base addr. */
sfrb(USBOEPBBAX_3, USBOEPBBAX_3_);
#define USBOEPCNF_3_          0x2398    /* Output Endpoint_3: Configuration */
sfrb(USBOEPCNF_3, USBOEPCNF_3_);
#define USBOEPSIZXY_2_        0x2397    /* Output Endpoint_2: X/Y-buffer size */
sfrb(USBOEPSIZXY_2, USBOEPSIZXY_2_);
#define USBOEPBCTY_2_         0x2396    /* Output Endpoint_2: Y-byte count */
sfrb(USBOEPBCTY_2, USBOEPBCTY_2_);
#define USBOEPBBAY_2_         0x2395    /* Output Endpoint_2: Y-buffer base addr. */
sfrb(USBOEPBBAY_2, USBOEPBBAY_2_);
//sfrb    Spare    (0x2394)   /* Not used */
//sfrb    Spare    (0x2393)   /* Not used */
#define USBOEPBCTX_2_         0x2392    /* Output Endpoint_2: X-byte count */
sfrb(USBOEPBCTX_2, USBOEPBCTX_2_);
#define USBOEPBBAX_2_         0x2391    /* Output Endpoint_2: X-buffer base addr. */
sfrb(USBOEPBBAX_2, USBOEPBBAX_2_);
#define USBOEPCNF_2_          0x2390    /* Output Endpoint_2: Configuration */
sfrb(USBOEPCNF_2, USBOEPCNF_2_);
#define USBOEPSIZXY_1_        0x238F    /* Output Endpoint_1: X/Y-buffer size */
sfrb(USBOEPSIZXY_1, USBOEPSIZXY_1_);
#define USBOEPBCTY_1_         0x238E    /* Output Endpoint_1: Y-byte count */
sfrb(USBOEPBCTY_1, USBOEPBCTY_1_);
#define USBOEPBBAY_1_         0x238D    /* Output Endpoint_1: Y-buffer base addr. */
sfrb(USBOEPBBAY_1, USBOEPBBAY_1_);
//sfrb    Spare    (0x238C)   /* Not used */
//sfrb    Spare    (0x238B)   /* Not used */
#define USBOEPBCTX_1_         0x238A    /* Output Endpoint_1: X-byte count */
sfrb(USBOEPBCTX_1, USBOEPBCTX_1_);
#define USBOEPBBAX_1_         0x2389    /* Output Endpoint_1: X-buffer base addr. */
sfrb(USBOEPBBAX_1, USBOEPBBAX_1_);
#define USBOEPCNF_1_          0x2388    /* Output Endpoint_1: Configuration */
sfrb(USBOEPCNF_1, USBOEPCNF_1_);
#define USBSUBLK_             0x2380    /* Setup Packet Block */
sfrb(USBSUBLK, USBSUBLK_);
#define USBIEP0BUF_           0x2378    /* Input endpoint_0 buffer */
sfrb(USBIEP0BUF, USBIEP0BUF_);
#define USBOEP0BUF_           0x2370    /* Output endpoint_0 buffer */
sfrb(USBOEP0BUF, USBOEP0BUF_);
#define USBTOPBUFF_           0x236F    /* Top of buffer space */
sfrb(USBTOPBUFF, USBTOPBUFF_);
//         (1904 Bytes)               /* Buffer space */
#define USBSTABUFF_           0x1C00    /* Start of buffer space */
sfrb(USBSTABUFF, USBSTABUFF_);

/* USBIEPCNF_n Control Bits */
/* USBOEPCNF_n Control Bits */
//#define RESERVED       (0x0001)  /* USB -  */
//#define RESERVED       (0x0001)  /* USB -  */
#define DBUF           (0x0010)  /* USB - Double Buffer Enable */
//#define RESERVED       (0x0040)  /* USB -  */

/* USBIEPBCNT_n Control Bits */
/* USBOEPBCNT_n Control Bits */
#define CNT4           (0x0010)  /* USB - Byte Count Bit 3 */
#define CNT5           (0x0020)  /* USB - Byte Count Bit 3 */
#define CNT6           (0x0040)  /* USB - Byte Count Bit 3 */
/************************************************************
* UNIFIED CLOCK SYSTEM
************************************************************/
#define __MSP430_HAS_UCS__            /* Definition to show that Module is available */

#define UCSCTL0_              0x0160    /* UCS Control Register 0 */
sfrb(UCSCTL0_L, UCSCTL0_);
sfrb(UCSCTL0_H, UCSCTL0_+1);
sfrw(UCSCTL0, UCSCTL0_);
#define UCSCTL1_              0x0162    /* UCS Control Register 1 */
sfrb(UCSCTL1_L, UCSCTL1_);
sfrb(UCSCTL1_H, UCSCTL1_+1);
sfrw(UCSCTL1, UCSCTL1_);
#define UCSCTL2_              0x0164    /* UCS Control Register 2 */
sfrb(UCSCTL2_L, UCSCTL2_);
sfrb(UCSCTL2_H, UCSCTL2_+1);
sfrw(UCSCTL2, UCSCTL2_);
#define UCSCTL3_              0x0166    /* UCS Control Register 3 */
sfrb(UCSCTL3_L, UCSCTL3_);
sfrb(UCSCTL3_H, UCSCTL3_+1);
sfrw(UCSCTL3, UCSCTL3_);
#define UCSCTL4_              0x0168    /* UCS Control Register 4 */
sfrb(UCSCTL4_L, UCSCTL4_);
sfrb(UCSCTL4_H, UCSCTL4_+1);
sfrw(UCSCTL4, UCSCTL4_);
#define UCSCTL5_              0x016A    /* UCS Control Register 5 */
sfrb(UCSCTL5_L, UCSCTL5_);
sfrb(UCSCTL5_H, UCSCTL5_+1);
sfrw(UCSCTL5, UCSCTL5_);
#define UCSCTL6_              0x016C    /* UCS Control Register 6 */
sfrb(UCSCTL6_L, UCSCTL6_);
sfrb(UCSCTL6_H, UCSCTL6_+1);
sfrw(UCSCTL6, UCSCTL6_);
#define UCSCTL7_              0x016E    /* UCS Control Register 7 */
sfrb(UCSCTL7_L, UCSCTL7_);
sfrb(UCSCTL7_H, UCSCTL7_+1);
sfrw(UCSCTL7, UCSCTL7_);
#define UCSCTL8_              0x0170    /* UCS Control Register 8 */
sfrb(UCSCTL8_L, UCSCTL8_);
sfrb(UCSCTL8_H, UCSCTL8_+1);
sfrw(UCSCTL8, UCSCTL8_);

/* UCSCTL0 Control Bits */
//#define RESERVED            (0x0001)    /* RESERVED */
//#define RESERVED            (0x0002)    /* RESERVED */
//#define RESERVED            (0x0004)    /* RESERVED */
#define MOD0                (0x0008)    /* Modulation Bit Counter Bit : 0 */
#define MOD1                (0x0010)    /* Modulation Bit Counter Bit : 1 */
#define MOD2                (0x0020)    /* Modulation Bit Counter Bit : 2 */
#define MOD3                (0x0040)    /* Modulation Bit Counter Bit : 3 */
#define MOD4                (0x0080)    /* Modulation Bit Counter Bit : 4 */
#define DCO0                (0x0100)    /* DCO TAP Bit : 0 */
#define DCO1                (0x0200)    /* DCO TAP Bit : 1 */
#define DCO2                (0x0400)    /* DCO TAP Bit : 2 */
#define DCO3                (0x0800)    /* DCO TAP Bit : 3 */
#define DCO4                (0x1000)    /* DCO TAP Bit : 4 */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL0 Control Bits */
//#define RESERVED            (0x0001)    /* RESERVED */
//#define RESERVED            (0x0002)    /* RESERVED */
//#define RESERVED            (0x0004)    /* RESERVED */
#define MOD0_L              (0x0008)    /* Modulation Bit Counter Bit : 0 */
#define MOD1_L              (0x0010)    /* Modulation Bit Counter Bit : 1 */
#define MOD2_L              (0x0020)    /* Modulation Bit Counter Bit : 2 */
#define MOD3_L              (0x0040)    /* Modulation Bit Counter Bit : 3 */
#define MOD4_L              (0x0080)    /* Modulation Bit Counter Bit : 4 */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL0 Control Bits */
//#define RESERVED            (0x0001)    /* RESERVED */
//#define RESERVED            (0x0002)    /* RESERVED */
//#define RESERVED            (0x0004)    /* RESERVED */
#define DCO0_H              (0x0001)    /* DCO TAP Bit : 0 */
#define DCO1_H              (0x0002)    /* DCO TAP Bit : 1 */
#define DCO2_H              (0x0004)    /* DCO TAP Bit : 2 */
#define DCO3_H              (0x0008)    /* DCO TAP Bit : 3 */
#define DCO4_H              (0x0010)    /* DCO TAP Bit : 4 */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL1 Control Bits */
#define DISMOD              (0x0001)    /* Disable Modulation */
#define DCOR                (0x0002)    /* DCO External Resistor Select */
//#define RESERVED            (0x0004)    /* RESERVED */
//#define RESERVED            (0x0008)    /* RESERVED */
#define DCORSEL0            (0x0010)    /* DCO Freq. Range Select Bit : 0 */
#define DCORSEL1            (0x0020)    /* DCO Freq. Range Select Bit : 1 */
#define DCORSEL2            (0x0040)    /* DCO Freq. Range Select Bit : 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL1 Control Bits */
#define DISMOD_L            (0x0001)    /* Disable Modulation */
#define DCOR_L              (0x0002)    /* DCO External Resistor Select */
//#define RESERVED            (0x0004)    /* RESERVED */
//#define RESERVED            (0x0008)    /* RESERVED */
#define DCORSEL0_L          (0x0010)    /* DCO Freq. Range Select Bit : 0 */
#define DCORSEL1_L          (0x0020)    /* DCO Freq. Range Select Bit : 1 */
#define DCORSEL2_L          (0x0040)    /* DCO Freq. Range Select Bit : 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL1 Control Bits */
//#define RESERVED            (0x0004)    /* RESERVED */
//#define RESERVED            (0x0008)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

#define DCORSEL_0           (0x0000)    /* DCO RSEL 0 */
#define DCORSEL_1           (0x0010)    /* DCO RSEL 1 */
#define DCORSEL_2           (0x0020)    /* DCO RSEL 2 */
#define DCORSEL_3           (0x0030)    /* DCO RSEL 3 */
#define DCORSEL_4           (0x0040)    /* DCO RSEL 4 */
#define DCORSEL_5           (0x0050)    /* DCO RSEL 5 */
#define DCORSEL_6           (0x0060)    /* DCO RSEL 6 */
#define DCORSEL_7           (0x0070)    /* DCO RSEL 7 */


/* UCSCTL2 Control Bits */
#define FLLN0               (0x0001)    /* FLL Multipier Bit : 0 */
#define FLLN1               (0x0002)    /* FLL Multipier Bit : 1 */
#define FLLN2               (0x0004)    /* FLL Multipier Bit : 2 */
#define FLLN3               (0x0008)    /* FLL Multipier Bit : 3 */
#define FLLN4               (0x0010)    /* FLL Multipier Bit : 4 */
#define FLLN5               (0x0020)    /* FLL Multipier Bit : 5 */
#define FLLN6               (0x0040)    /* FLL Multipier Bit : 6 */
#define FLLN7               (0x0080)    /* FLL Multipier Bit : 7 */
#define FLLN8               (0x0100)    /* FLL Multipier Bit : 8 */
#define FLLN9               (0x0200)    /* FLL Multipier Bit : 9 */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
#define FLLD0               (0x1000)    /* Loop Divider Bit : 0 */
#define FLLD1               (0x2000)    /* Loop Divider Bit : 1 */
#define FLLD2               (0x4000)    /* Loop Divider Bit : 1 */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL2 Control Bits */
#define FLLN0_L             (0x0001)    /* FLL Multipier Bit : 0 */
#define FLLN1_L             (0x0002)    /* FLL Multipier Bit : 1 */
#define FLLN2_L             (0x0004)    /* FLL Multipier Bit : 2 */
#define FLLN3_L             (0x0008)    /* FLL Multipier Bit : 3 */
#define FLLN4_L             (0x0010)    /* FLL Multipier Bit : 4 */
#define FLLN5_L             (0x0020)    /* FLL Multipier Bit : 5 */
#define FLLN6_L             (0x0040)    /* FLL Multipier Bit : 6 */
#define FLLN7_L             (0x0080)    /* FLL Multipier Bit : 7 */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL2 Control Bits */
#define FLLN8_H             (0x0001)    /* FLL Multipier Bit : 8 */
#define FLLN9_H             (0x0002)    /* FLL Multipier Bit : 9 */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
#define FLLD0_H             (0x0010)    /* Loop Divider Bit : 0 */
#define FLLD1_H             (0x0020)    /* Loop Divider Bit : 1 */
#define FLLD2_H             (0x0040)    /* Loop Divider Bit : 1 */
//#define RESERVED            (0x8000)    /* RESERVED */

#define FLLD_0             (0x0000)    /* Multiply Selected Loop Freq. 1 */
#define FLLD_1             (0x1000)    /* Multiply Selected Loop Freq. 2 */
#define FLLD_2             (0x2000)    /* Multiply Selected Loop Freq. 4 */
#define FLLD_3             (0x3000)    /* Multiply Selected Loop Freq. 8 */
#define FLLD_4             (0x4000)    /* Multiply Selected Loop Freq. 16 */
#define FLLD_5             (0x5000)    /* Multiply Selected Loop Freq. 32 */
#define FLLD_6             (0x6000)    /* Multiply Selected Loop Freq. 32 */
#define FLLD_7             (0x7000)    /* Multiply Selected Loop Freq. 32 */
#define FLLD__1            (0x0000)    /* Multiply Selected Loop Freq. By 1 */
#define FLLD__2            (0x1000)    /* Multiply Selected Loop Freq. By 2 */
#define FLLD__4            (0x2000)    /* Multiply Selected Loop Freq. By 4 */
#define FLLD__8            (0x3000)    /* Multiply Selected Loop Freq. By 8 */
#define FLLD__16           (0x4000)    /* Multiply Selected Loop Freq. By 16 */
#define FLLD__32           (0x5000)    /* Multiply Selected Loop Freq. By 32 */


/* UCSCTL3 Control Bits */
#define FLLREFDIV0          (0x0001)    /* Reference Divider Bit : 0 */
#define FLLREFDIV1          (0x0002)    /* Reference Divider Bit : 1 */
#define FLLREFDIV2          (0x0004)    /* Reference Divider Bit : 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define SELREF0             (0x0010)    /* FLL Reference Clock Select Bit : 0 */
#define SELREF1             (0x0020)    /* FLL Reference Clock Select Bit : 1 */
#define SELREF2             (0x0040)    /* FLL Reference Clock Select Bit : 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL3 Control Bits */
#define FLLREFDIV0_L        (0x0001)    /* Reference Divider Bit : 0 */
#define FLLREFDIV1_L        (0x0002)    /* Reference Divider Bit : 1 */
#define FLLREFDIV2_L        (0x0004)    /* Reference Divider Bit : 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define SELREF0_L           (0x0010)    /* FLL Reference Clock Select Bit : 0 */
#define SELREF1_L           (0x0020)    /* FLL Reference Clock Select Bit : 1 */
#define SELREF2_L           (0x0040)    /* FLL Reference Clock Select Bit : 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL3 Control Bits */
//#define RESERVED            (0x0008)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

#define FLLREFDIV_0         (0x0000)    /* Reference Divider: f(LFCLK)/1 */
#define FLLREFDIV_1         (0x0001)    /* Reference Divider: f(LFCLK)/2 */
#define FLLREFDIV_2         (0x0002)    /* Reference Divider: f(LFCLK)/4 */
#define FLLREFDIV_3         (0x0003)    /* Reference Divider: f(LFCLK)/8 */
#define FLLREFDIV_4         (0x0004)    /* Reference Divider: f(LFCLK)/12 */
#define FLLREFDIV_5         (0x0005)    /* Reference Divider: f(LFCLK)/16 */
#define FLLREFDIV_6         (0x0006)    /* Reference Divider: f(LFCLK)/16 */
#define FLLREFDIV_7         (0x0007)    /* Reference Divider: f(LFCLK)/16 */
#define FLLREFDIV__1        (0x0000)    /* Reference Divider: f(LFCLK)/1 */
#define FLLREFDIV__2        (0x0001)    /* Reference Divider: f(LFCLK)/2 */
#define FLLREFDIV__4        (0x0002)    /* Reference Divider: f(LFCLK)/4 */
#define FLLREFDIV__8        (0x0003)    /* Reference Divider: f(LFCLK)/8 */
#define FLLREFDIV__12       (0x0004)    /* Reference Divider: f(LFCLK)/12 */
#define FLLREFDIV__16       (0x0005)    /* Reference Divider: f(LFCLK)/16 */
#define SELREF_0            (0x0000)    /* FLL Reference Clock Select 0 */
#define SELREF_1            (0x0010)    /* FLL Reference Clock Select 1 */
#define SELREF_2            (0x0020)    /* FLL Reference Clock Select 2 */
#define SELREF_3            (0x0030)    /* FLL Reference Clock Select 3 */
#define SELREF_4            (0x0040)    /* FLL Reference Clock Select 4 */
#define SELREF_5            (0x0050)    /* FLL Reference Clock Select 5 */
#define SELREF_6            (0x0060)    /* FLL Reference Clock Select 6 */
#define SELREF_7            (0x0070)    /* FLL Reference Clock Select 7 */
#define SELREF__XT1CLK      (0x0000)    /* Multiply Selected Loop Freq. By XT1CLK */
#define SELREF__REFOCLK     (0x0020)    /* Multiply Selected Loop Freq. By REFOCLK */
#define SELREF__XT2CLK      (0x0050)    /* Multiply Selected Loop Freq. By XT2CLK */

/* UCSCTL4 Control Bits */
#define SELM0               (0x0001)   /* MCLK Source Select Bit: 0 */
#define SELM1               (0x0002)   /* MCLK Source Select Bit: 1 */
#define SELM2               (0x0004)   /* MCLK Source Select Bit: 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define SELS0               (0x0010)   /* SMCLK Source Select Bit: 0 */
#define SELS1               (0x0020)   /* SMCLK Source Select Bit: 1 */
#define SELS2               (0x0040)   /* SMCLK Source Select Bit: 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
#define SELA0               (0x0100)   /* ACLK Source Select Bit: 0 */
#define SELA1               (0x0200)   /* ACLK Source Select Bit: 1 */
#define SELA2               (0x0400)   /* ACLK Source Select Bit: 2 */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL4 Control Bits */
#define SELM0_L             (0x0001)   /* MCLK Source Select Bit: 0 */
#define SELM1_L             (0x0002)   /* MCLK Source Select Bit: 1 */
#define SELM2_L             (0x0004)   /* MCLK Source Select Bit: 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define SELS0_L             (0x0010)   /* SMCLK Source Select Bit: 0 */
#define SELS1_L             (0x0020)   /* SMCLK Source Select Bit: 1 */
#define SELS2_L             (0x0040)   /* SMCLK Source Select Bit: 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL4 Control Bits */
//#define RESERVED            (0x0008)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
#define SELA0_H             (0x0001)   /* ACLK Source Select Bit: 0 */
#define SELA1_H             (0x0002)   /* ACLK Source Select Bit: 1 */
#define SELA2_H             (0x0004)   /* ACLK Source Select Bit: 2 */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

#define SELM_0              (0x0000)   /* MCLK Source Select 0 */
#define SELM_1              (0x0001)   /* MCLK Source Select 1 */
#define SELM_2              (0x0002)   /* MCLK Source Select 2 */
#define SELM_3              (0x0003)   /* MCLK Source Select 3 */
#define SELM_4              (0x0004)   /* MCLK Source Select 4 */
#define SELM_5              (0x0005)   /* MCLK Source Select 5 */
#define SELM_6              (0x0006)   /* MCLK Source Select 6 */
#define SELM_7              (0x0007)   /* MCLK Source Select 7 */
#define SELM__XT1CLK        (0x0000)   /* MCLK Source Select XT1CLK */
#define SELM__VLOCLK        (0x0001)   /* MCLK Source Select VLOCLK */
#define SELM__REFOCLK       (0x0002)   /* MCLK Source Select REFOCLK */
#define SELM__DCOCLK        (0x0003)   /* MCLK Source Select DCOCLK */
#define SELM__DCOCLKDIV     (0x0004)   /* MCLK Source Select DCOCLKDIV */
#define SELM__XT2CLK        (0x0005)   /* MCLK Source Select XT2CLK */

#define SELS_0              (0x0000)   /* SMCLK Source Select 0 */
#define SELS_1              (0x0010)   /* SMCLK Source Select 1 */
#define SELS_2              (0x0020)   /* SMCLK Source Select 2 */
#define SELS_3              (0x0030)   /* SMCLK Source Select 3 */
#define SELS_4              (0x0040)   /* SMCLK Source Select 4 */
#define SELS_5              (0x0050)   /* SMCLK Source Select 5 */
#define SELS_6              (0x0060)   /* SMCLK Source Select 6 */
#define SELS_7              (0x0070)   /* SMCLK Source Select 7 */
#define SELS__XT1CLK        (0x0000)   /* SMCLK Source Select XT1CLK */
#define SELS__VLOCLK        (0x0010)   /* SMCLK Source Select VLOCLK */
#define SELS__REFOCLK       (0x0020)   /* SMCLK Source Select REFOCLK */
#define SELS__DCOCLK        (0x0030)   /* SMCLK Source Select DCOCLK */
#define SELS__DCOCLKDIV     (0x0040)   /* SMCLK Source Select DCOCLKDIV */
#define SELS__XT2CLK        (0x0050)   /* SMCLK Source Select XT2CLK */

#define SELA_0              (0x0000)   /* ACLK Source Select 0 */
#define SELA_1              (0x0100)   /* ACLK Source Select 1 */
#define SELA_2              (0x0200)   /* ACLK Source Select 2 */
#define SELA_3              (0x0300)   /* ACLK Source Select 3 */
#define SELA_4              (0x0400)   /* ACLK Source Select 4 */
#define SELA_5              (0x0500)   /* ACLK Source Select 5 */
#define SELA_6              (0x0600)   /* ACLK Source Select 6 */
#define SELA_7              (0x0700)   /* ACLK Source Select 7 */
#define SELA__XT1CLK        (0x0000)   /* ACLK Source Select XT1CLK */
#define SELA__VLOCLK        (0x0100)   /* ACLK Source Select VLOCLK */
#define SELA__REFOCLK       (0x0200)   /* ACLK Source Select REFOCLK */
#define SELA__DCOCLK        (0x0300)   /* ACLK Source Select DCOCLK */
#define SELA__DCOCLKDIV     (0x0400)   /* ACLK Source Select DCOCLKDIV */
#define SELA__XT2CLK        (0x0500)   /* ACLK Source Select XT2CLK */

/* UCSCTL5 Control Bits */
#define DIVM0               (0x0001)   /* MCLK Divider Bit: 0 */
#define DIVM1               (0x0002)   /* MCLK Divider Bit: 1 */
#define DIVM2               (0x0004)   /* MCLK Divider Bit: 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define DIVS0               (0x0010)   /* SMCLK Divider Bit: 0 */
#define DIVS1               (0x0020)   /* SMCLK Divider Bit: 1 */
#define DIVS2               (0x0040)   /* SMCLK Divider Bit: 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
#define DIVA0               (0x0100)   /* ACLK Divider Bit: 0 */
#define DIVA1               (0x0200)   /* ACLK Divider Bit: 1 */
#define DIVA2               (0x0400)   /* ACLK Divider Bit: 2 */
//#define RESERVED            (0x0800)    /* RESERVED */
#define DIVPA0              (0x1000)   /* ACLK from Pin Divider Bit: 0 */
#define DIVPA1              (0x2000)   /* ACLK from Pin Divider Bit: 1 */
#define DIVPA2              (0x4000)   /* ACLK from Pin Divider Bit: 2 */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL5 Control Bits */
#define DIVM0_L             (0x0001)   /* MCLK Divider Bit: 0 */
#define DIVM1_L             (0x0002)   /* MCLK Divider Bit: 1 */
#define DIVM2_L             (0x0004)   /* MCLK Divider Bit: 2 */
//#define RESERVED            (0x0008)    /* RESERVED */
#define DIVS0_L             (0x0010)   /* SMCLK Divider Bit: 0 */
#define DIVS1_L             (0x0020)   /* SMCLK Divider Bit: 1 */
#define DIVS2_L             (0x0040)   /* SMCLK Divider Bit: 2 */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL5 Control Bits */
//#define RESERVED            (0x0008)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
#define DIVA0_H             (0x0001)   /* ACLK Divider Bit: 0 */
#define DIVA1_H             (0x0002)   /* ACLK Divider Bit: 1 */
#define DIVA2_H             (0x0004)   /* ACLK Divider Bit: 2 */
//#define RESERVED            (0x0800)    /* RESERVED */
#define DIVPA0_H            (0x0010)   /* ACLK from Pin Divider Bit: 0 */
#define DIVPA1_H            (0x0020)   /* ACLK from Pin Divider Bit: 1 */
#define DIVPA2_H            (0x0040)   /* ACLK from Pin Divider Bit: 2 */
//#define RESERVED            (0x8000)    /* RESERVED */

#define DIVM_0              (0x0000)    /* MCLK Source Divider 0 */
#define DIVM_1              (0x0001)    /* MCLK Source Divider 1 */
#define DIVM_2              (0x0002)    /* MCLK Source Divider 2 */
#define DIVM_3              (0x0003)    /* MCLK Source Divider 3 */
#define DIVM_4              (0x0004)    /* MCLK Source Divider 4 */
#define DIVM_5              (0x0005)    /* MCLK Source Divider 5 */
#define DIVM_6              (0x0006)    /* MCLK Source Divider 6 */
#define DIVM_7              (0x0007)    /* MCLK Source Divider 7 */
#define DIVM__1             (0x0000)    /* MCLK Source Divider f(MCLK)/1 */
#define DIVM__2             (0x0001)    /* MCLK Source Divider f(MCLK)/2 */
#define DIVM__4             (0x0002)    /* MCLK Source Divider f(MCLK)/4 */
#define DIVM__8             (0x0003)    /* MCLK Source Divider f(MCLK)/8 */
#define DIVM__16            (0x0004)    /* MCLK Source Divider f(MCLK)/16 */
#define DIVM__32            (0x0005)    /* MCLK Source Divider f(MCLK)/32 */

#define DIVS_0              (0x0000)    /* SMCLK Source Divider 0 */
#define DIVS_1              (0x0010)    /* SMCLK Source Divider 1 */
#define DIVS_2              (0x0020)    /* SMCLK Source Divider 2 */
#define DIVS_3              (0x0030)    /* SMCLK Source Divider 3 */
#define DIVS_4              (0x0040)    /* SMCLK Source Divider 4 */
#define DIVS_5              (0x0050)    /* SMCLK Source Divider 5 */
#define DIVS_6              (0x0060)    /* SMCLK Source Divider 6 */
#define DIVS_7              (0x0070)    /* SMCLK Source Divider 7 */
#define DIVS__1             (0x0000)    /* SMCLK Source Divider f(SMCLK)/1 */
#define DIVS__2             (0x0010)    /* SMCLK Source Divider f(SMCLK)/2 */
#define DIVS__4             (0x0020)    /* SMCLK Source Divider f(SMCLK)/4 */
#define DIVS__8             (0x0030)    /* SMCLK Source Divider f(SMCLK)/8 */
#define DIVS__16            (0x0040)    /* SMCLK Source Divider f(SMCLK)/16 */
#define DIVS__32            (0x0050)    /* SMCLK Source Divider f(SMCLK)/32 */

#define DIVA_0              (0x0000)    /* ACLK Source Divider 0 */
#define DIVA_1              (0x0100)    /* ACLK Source Divider 1 */
#define DIVA_2              (0x0200)    /* ACLK Source Divider 2 */
#define DIVA_3              (0x0300)    /* ACLK Source Divider 3 */
#define DIVA_4              (0x0400)    /* ACLK Source Divider 4 */
#define DIVA_5              (0x0500)    /* ACLK Source Divider 5 */
#define DIVA_6              (0x0600)    /* ACLK Source Divider 6 */
#define DIVA_7              (0x0700)    /* ACLK Source Divider 7 */
#define DIVA__1             (0x0000)    /* ACLK Source Divider f(ACLK)/1 */
#define DIVA__2             (0x0100)    /* ACLK Source Divider f(ACLK)/2 */
#define DIVA__4             (0x0200)    /* ACLK Source Divider f(ACLK)/4 */
#define DIVA__8             (0x0300)    /* ACLK Source Divider f(ACLK)/8 */
#define DIVA__16            (0x0400)    /* ACLK Source Divider f(ACLK)/16 */
#define DIVA__32            (0x0500)    /* ACLK Source Divider f(ACLK)/32 */

#define DIVPA_0             (0x0000)    /* ACLK from Pin Source Divider 0 */
#define DIVPA_1             (0x1000)    /* ACLK from Pin Source Divider 1 */
#define DIVPA_2             (0x2000)    /* ACLK from Pin Source Divider 2 */
#define DIVPA_3             (0x3000)    /* ACLK from Pin Source Divider 3 */
#define DIVPA_4             (0x4000)    /* ACLK from Pin Source Divider 4 */
#define DIVPA_5             (0x5000)    /* ACLK from Pin Source Divider 5 */
#define DIVPA_6             (0x6000)    /* ACLK from Pin Source Divider 6 */
#define DIVPA_7             (0x7000)    /* ACLK from Pin Source Divider 7 */
#define DIVPA__1            (0x0000)    /* ACLK from Pin Source Divider f(ACLK)/1 */
#define DIVPA__2            (0x1000)    /* ACLK from Pin Source Divider f(ACLK)/2 */
#define DIVPA__4            (0x2000)    /* ACLK from Pin Source Divider f(ACLK)/4 */
#define DIVPA__8            (0x3000)    /* ACLK from Pin Source Divider f(ACLK)/8 */
#define DIVPA__16           (0x4000)    /* ACLK from Pin Source Divider f(ACLK)/16 */
#define DIVPA__32           (0x5000)    /* ACLK from Pin Source Divider f(ACLK)/32 */


/* UCSCTL6 Control Bits */
#define XT1OFF              (0x0001)    /* High Frequency Oscillator 1 (XT1) disable */
#define SMCLKOFF            (0x0002)    /* SMCLK Off */
#define XCAP0               (0x0004)   /* XIN/XOUT Cap Bit: 0 */
#define XCAP1               (0x0008)   /* XIN/XOUT Cap Bit: 1 */
#define XT1BYPASS           (0x0010)    /* XT1 bypass mode : 0: internal 1:sourced from external pin */
#define XTS                 (0x0020)   /* 1: Selects high-freq. oscillator */
#define XT1DRIVE0           (0x0040)    /* XT1 Drive Level mode Bit 0 */
#define XT1DRIVE1           (0x0080)    /* XT1 Drive Level mode Bit 1 */
#define XT2OFF              (0x0100)    /* High Frequency Oscillator 2 (XT2) disable */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
#define XT2BYPASS           (0x1000)    /* XT2 bypass mode : 0: internal 1:sourced from external pin */
//#define RESERVED            (0x2000)    /* RESERVED */
#define XT2DRIVE0           (0x4000)    /* XT2 Drive Level mode Bit 0 */
#define XT2DRIVE1           (0x8000)    /* XT2 Drive Level mode Bit 1 */

/* UCSCTL6 Control Bits */
#define XT1OFF_L            (0x0001)    /* High Frequency Oscillator 1 (XT1) disable */
#define SMCLKOFF_L          (0x0002)    /* SMCLK Off */
#define XCAP0_L             (0x0004)   /* XIN/XOUT Cap Bit: 0 */
#define XCAP1_L             (0x0008)   /* XIN/XOUT Cap Bit: 1 */
#define XT1BYPASS_L         (0x0010)    /* XT1 bypass mode : 0: internal 1:sourced from external pin */
#define XTS_L               (0x0020)   /* 1: Selects high-freq. oscillator */
#define XT1DRIVE0_L         (0x0040)    /* XT1 Drive Level mode Bit 0 */
#define XT1DRIVE1_L         (0x0080)    /* XT1 Drive Level mode Bit 1 */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */

/* UCSCTL6 Control Bits */
#define XT2OFF_H            (0x0001)    /* High Frequency Oscillator 2 (XT2) disable */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
#define XT2BYPASS_H         (0x0010)    /* XT2 bypass mode : 0: internal 1:sourced from external pin */
//#define RESERVED            (0x2000)    /* RESERVED */
#define XT2DRIVE0_H         (0x0040)    /* XT2 Drive Level mode Bit 0 */
#define XT2DRIVE1_H         (0x0080)    /* XT2 Drive Level mode Bit 1 */

#define XCAP_0              (0x0000)    /* XIN/XOUT Cap 0 */
#define XCAP_1              (0x0004)    /* XIN/XOUT Cap 1 */
#define XCAP_2              (0x0008)    /* XIN/XOUT Cap 2 */
#define XCAP_3              (0x000C)    /* XIN/XOUT Cap 3 */
#define XT1DRIVE_0          (0x0000)    /* XT1 Drive Level mode: 0 */
#define XT1DRIVE_1          (0x0040)    /* XT1 Drive Level mode: 1 */
#define XT1DRIVE_2          (0x0080)    /* XT1 Drive Level mode: 2 */
#define XT1DRIVE_3          (0x00C0)    /* XT1 Drive Level mode: 3 */
#define XT2DRIVE_0          (0x0000)    /* XT2 Drive Level mode: 0 */
#define XT2DRIVE_1          (0x4000)    /* XT2 Drive Level mode: 1 */
#define XT2DRIVE_2          (0x8000)    /* XT2 Drive Level mode: 2 */
#define XT2DRIVE_3          (0xC000)    /* XT2 Drive Level mode: 3 */


/* UCSCTL7 Control Bits */
#define DCOFFG              (0x0001)    /* DCO Fault Flag */
#define XT1LFOFFG           (0x0002)    /* XT1 Low Frequency Oscillator Fault Flag */
//#define RESERVED            (0x0004)    /* RESERVED */
#define XT2OFFG             (0x0008)    /* High Frequency Oscillator 2 Fault Flag */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL7 Control Bits */
#define DCOFFG_L            (0x0001)    /* DCO Fault Flag */
#define XT1LFOFFG_L         (0x0002)    /* XT1 Low Frequency Oscillator Fault Flag */
//#define RESERVED            (0x0004)    /* RESERVED */
#define XT2OFFG_L           (0x0008)    /* High Frequency Oscillator 2 Fault Flag */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL7 Control Bits */
//#define RESERVED            (0x0004)    /* RESERVED */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */


/* UCSCTL8 Control Bits */
#define ACLKREQEN           (0x0001)    /* ACLK Clock Request Enable */
#define MCLKREQEN           (0x0002)    /* MCLK Clock Request Enable */
#define SMCLKREQEN          (0x0004)    /* SMCLK Clock Request Enable */
#define MODOSCREQEN         (0x0008)    /* MODOSC Clock Request Enable */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL8 Control Bits */
#define ACLKREQEN_L         (0x0001)    /* ACLK Clock Request Enable */
#define MCLKREQEN_L         (0x0002)    /* MCLK Clock Request Enable */
#define SMCLKREQEN_L        (0x0004)    /* SMCLK Clock Request Enable */
#define MODOSCREQEN_L       (0x0008)    /* MODOSC Clock Request Enable */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/* UCSCTL8 Control Bits */
//#define RESERVED            (0x0010)    /* RESERVED */
//#define RESERVED            (0x0020)    /* RESERVED */
//#define RESERVED            (0x0040)    /* RESERVED */
//#define RESERVED            (0x0080)    /* RESERVED */
//#define RESERVED            (0x0100)    /* RESERVED */
//#define RESERVED            (0x0200)    /* RESERVED */
//#define RESERVED            (0x0400)    /* RESERVED */
//#define RESERVED            (0x0800)    /* RESERVED */
//#define RESERVED            (0x1000)    /* RESERVED */
//#define RESERVED            (0x2000)    /* RESERVED */
//#define RESERVED            (0x4000)    /* RESERVED */
//#define RESERVED            (0x8000)    /* RESERVED */

/************************************************************
* USCI A0
************************************************************/
#define __MSP430_HAS_USCI_A0__       /* Definition to show that Module is available */

#define UCA0CTLW0_            0x05C0    /* USCI A0 Control Word Register 0 */
sfrb(UCA0CTLW0_L, UCA0CTLW0_);
sfrb(UCA0CTLW0_H, UCA0CTLW0_+1);
sfrw(UCA0CTLW0, UCA0CTLW0_);
#define UCA0CTL1            UCA0CTLW0_L  /* USCI A0 Control Register 1 */
#define UCA0CTL0            UCA0CTLW0_H  /* USCI A0 Control Register 0 */
#define UCA0BRW_              0x05C6    /* USCI A0 Baud Word Rate 0 */
sfrb(UCA0BRW_L, UCA0BRW_);
sfrb(UCA0BRW_H, UCA0BRW_+1);
sfrw(UCA0BRW, UCA0BRW_);
#define UCA0BR0             UCA0BRW_L /* USCI A0 Baud Rate 0 */
#define UCA0BR1             UCA0BRW_H /* USCI A0 Baud Rate 1 */
#define UCA0MCTL_             0x05C8    /* USCI A0 Modulation Control */
sfrb(UCA0MCTL, UCA0MCTL_);
#define UCA0STAT_             0x05CA    /* USCI A0 Status Register */
sfrb(UCA0STAT, UCA0STAT_);
#define UCA0RXBUF_            0x05CC    /* USCI A0 Receive Buffer */
const_sfrb(UCA0RXBUF, UCA0RXBUF_);
#define UCA0TXBUF_            0x05CE    /* USCI A0 Transmit Buffer */
sfrb(UCA0TXBUF, UCA0TXBUF_);
#define UCA0ABCTL_            0x05D0    /* USCI A0 LIN Control */
sfrb(UCA0ABCTL, UCA0ABCTL_);
#define UCA0IRCTL_            0x05D2    /* USCI A0 IrDA Transmit Control */
sfrb(UCA0IRCTL_L, UCA0IRCTL_);
sfrb(UCA0IRCTL_H, UCA0IRCTL_+1);
sfrw(UCA0IRCTL, UCA0IRCTL_);
#define UCA0IRTCTL          UCA0IRCTL_L  /* USCI A0 IrDA Transmit Control */
#define UCA0IRRCTL          UCA0IRCTL_H  /* USCI A0 IrDA Receive Control */
#define UCA0ICTL_             0x05DC    /* USCI A0 Interrupt Enable Register */
sfrb(UCA0ICTL_L, UCA0ICTL_);
sfrb(UCA0ICTL_H, UCA0ICTL_+1);
sfrw(UCA0ICTL, UCA0ICTL_);
#define UCA0IE              UCA0ICTL_L  /* USCI A0 Interrupt Enable Register */
#define UCA0IFG             UCA0ICTL_H  /* USCI A0 Interrupt Flags Register */
#define UCA0IV_               0x05DE    /* USCI A0 Interrupt Vector Register */
sfrw(UCA0IV, UCA0IV_);


/************************************************************
* USCI B0
************************************************************/
#define __MSP430_HAS_USCI_B0__        /* Definition to show that Module is available */


#define UCB0CTLW0_            0x05E0    /* USCI B0 Control Word Register 0 */
sfrb(UCB0CTLW0_L, UCB0CTLW0_);
sfrb(UCB0CTLW0_H, UCB0CTLW0_+1);
sfrw(UCB0CTLW0, UCB0CTLW0_);
#define UCB0CTL1            UCB0CTLW0_L  /* USCI B0 Control Register 1 */
#define UCB0CTL0            UCB0CTLW0_H  /* USCI B0 Control Register 0 */
#define UCB0BRW_              0x05E6    /* USCI B0 Baud Word Rate 0 */
sfrb(UCB0BRW_L, UCB0BRW_);
sfrb(UCB0BRW_H, UCB0BRW_+1);
sfrw(UCB0BRW, UCB0BRW_);
#define UCB0BR0             UCB0BRW_L /* USCI B0 Baud Rate 0 */
#define UCB0BR1             UCB0BRW_H /* USCI B0 Baud Rate 1 */
#define UCB0STAT_             0x05EA    /* USCI B0 Status Register */
sfrb(UCB0STAT, UCB0STAT_);
#define UCB0RXBUF_            0x05EC    /* USCI B0 Receive Buffer */
const_sfrb(UCB0RXBUF, UCB0RXBUF_);
#define UCB0TXBUF_            0x05EE    /* USCI B0 Transmit Buffer */
sfrb(UCB0TXBUF, UCB0TXBUF_);
#define UCB0I2COA_            0x05F0    /* USCI B0 I2C Own Address */
sfrb(UCB0I2COA_L, UCB0I2COA_);
sfrb(UCB0I2COA_H, UCB0I2COA_+1);
sfrw(UCB0I2COA, UCB0I2COA_);
#define UCB0I2CSA_            0x05F2    /* USCI B0 I2C Slave Address */
sfrb(UCB0I2CSA_L, UCB0I2CSA_);
sfrb(UCB0I2CSA_H, UCB0I2CSA_+1);
sfrw(UCB0I2CSA, UCB0I2CSA_);
#define UCB0ICTL_             0x05FC    /* USCI B0 Interrupt Enable Register */
sfrb(UCB0ICTL_L, UCB0ICTL_);
sfrb(UCB0ICTL_H, UCB0ICTL_+1);
sfrw(UCB0ICTL, UCB0ICTL_);
#define UCB0IE              UCB0ICTL_L  /* USCI B0 Interrupt Enable Register */
#define UCB0IFG             UCB0ICTL_H  /* USCI B0 Interrupt Flags Register */
#define UCB0IV_               0x05FE    /* USCI B0 Interrupt Vector Register */
sfrw(UCB0IV, UCB0IV_);


// UCAxCTL0 UART-Mode Control Bits
#define UCPEN               (0x80)    /* Async. Mode: Parity enable */
#define UCPAR               (0x40)    /* Async. Mode: Parity     0:odd / 1:even */
#define UCMSB               (0x20)    /* Async. Mode: MSB first  0:LSB / 1:MSB */
#define UC7BIT              (0x10)    /* Async. Mode: Data Bits  0:8-bits / 1:7-bits */
#define UCSPB               (0x08)    /* Async. Mode: Stop Bits  0:one / 1: two */
#define UCMODE1             (0x04)    /* Async. Mode: USCI Mode 1 */
#define UCMODE0             (0x02)    /* Async. Mode: USCI Mode 0 */
#define UCSYNC              (0x01)    /* Sync-Mode  0:UART-Mode / 1:SPI-Mode */

// UCxxCTL0 SPI-Mode Control Bits
#define UCCKPH              (0x80)    /* Sync. Mode: Clock Phase */
#define UCCKPL              (0x40)    /* Sync. Mode: Clock Polarity */
#define UCMST               (0x08)    /* Sync. Mode: Master Select */

// UCBxCTL0 I2C-Mode Control Bits
#define UCA10               (0x80)    /* 10-bit Address Mode */
#define UCSLA10             (0x40)    /* 10-bit Slave Address Mode */
#define UCMM                (0x20)    /* Multi-Master Environment */
//#define res               (0x10)    /* reserved */
#define UCMODE_0            (0x00)    /* Sync. Mode: USCI Mode: 0 */
#define UCMODE_1            (0x02)    /* Sync. Mode: USCI Mode: 1 */
#define UCMODE_2            (0x04)    /* Sync. Mode: USCI Mode: 2 */
#define UCMODE_3            (0x06)    /* Sync. Mode: USCI Mode: 3 */

// UCAxCTL1 UART-Mode Control Bits
#define UCSSEL1             (0x80)    /* USCI 0 Clock Source Select 1 */
#define UCSSEL0             (0x40)    /* USCI 0 Clock Source Select 0 */
#define UCRXEIE             (0x20)    /* RX Error interrupt enable */
#define UCBRKIE             (0x10)    /* Break interrupt enable */                   
#define UCDORM              (0x08)    /* Dormant (Sleep) Mode */
#define UCTXADDR            (0x04)    /* Send next Data as Address */
#define UCTXBRK             (0x02)    /* Send next Data as Break */
#define UCSWRST             (0x01)    /* USCI Software Reset */

// UCxxCTL1 SPI-Mode Control Bits
//#define res               (0x20)    /* reserved */
//#define res               (0x10)    /* reserved */
//#define res               (0x08)    /* reserved */
//#define res               (0x04)    /* reserved */
//#define res               (0x02)    /* reserved */

// UCBxCTL1 I2C-Mode Control Bits
//#define res               (0x20)    /* reserved */
#define UCTR                (0x10)    /* Transmit/Receive Select/Flag */
#define UCTXNACK            (0x08)    /* Transmit NACK */
#define UCTXSTP             (0x04)    /* Transmit STOP */
#define UCTXSTT             (0x02)    /* Transmit START */
#define UCSSEL_0            (0x00)    /* USCI 0 Clock Source: 0 */
#define UCSSEL_1            (0x40)    /* USCI 0 Clock Source: 1 */
#define UCSSEL_2            (0x80)    /* USCI 0 Clock Source: 2 */
#define UCSSEL_3            (0xC0)    /* USCI 0 Clock Source: 3 */
#define UCSSEL__UCLK        (0x00)    /* USCI 0 Clock Source: UCLK */
#define UCSSEL__ACLK        (0x40)    /* USCI 0 Clock Source: ACLK */
#define UCSSEL__SMCLK       (0x80)    /* USCI 0 Clock Source: SMCLK */

/* UCAxMCTL Control Bits */
#define UCBRF3              (0x80)    /* USCI First Stage Modulation Select 3 */
#define UCBRF2              (0x40)    /* USCI First Stage Modulation Select 2 */
#define UCBRF1              (0x20)    /* USCI First Stage Modulation Select 1 */
#define UCBRF0              (0x10)    /* USCI First Stage Modulation Select 0 */
#define UCBRS2              (0x08)    /* USCI Second Stage Modulation Select 2 */
#define UCBRS1              (0x04)    /* USCI Second Stage Modulation Select 1 */
#define UCBRS0              (0x02)    /* USCI Second Stage Modulation Select 0 */
#define UCOS16              (0x01)    /* USCI 16-times Oversampling enable */

#define UCBRF_0             (0x00)    /* USCI First Stage Modulation: 0 */
#define UCBRF_1             (0x10)    /* USCI First Stage Modulation: 1 */
#define UCBRF_2             (0x20)    /* USCI First Stage Modulation: 2 */
#define UCBRF_3             (0x30)    /* USCI First Stage Modulation: 3 */
#define UCBRF_4             (0x40)    /* USCI First Stage Modulation: 4 */
#define UCBRF_5             (0x50)    /* USCI First Stage Modulation: 5 */
#define UCBRF_6             (0x60)    /* USCI First Stage Modulation: 6 */
#define UCBRF_7             (0x70)    /* USCI First Stage Modulation: 7 */
#define UCBRF_8             (0x80)    /* USCI First Stage Modulation: 8 */
#define UCBRF_9             (0x90)    /* USCI First Stage Modulation: 9 */
#define UCBRF_10            (0xA0)    /* USCI First Stage Modulation: A */
#define UCBRF_11            (0xB0)    /* USCI First Stage Modulation: B */
#define UCBRF_12            (0xC0)    /* USCI First Stage Modulation: C */
#define UCBRF_13            (0xD0)    /* USCI First Stage Modulation: D */
#define UCBRF_14            (0xE0)    /* USCI First Stage Modulation: E */
#define UCBRF_15            (0xF0)    /* USCI First Stage Modulation: F */

#define UCBRS_0             (0x00)    /* USCI Second Stage Modulation: 0 */
#define UCBRS_1             (0x02)    /* USCI Second Stage Modulation: 1 */
#define UCBRS_2             (0x04)    /* USCI Second Stage Modulation: 2 */
#define UCBRS_3             (0x06)    /* USCI Second Stage Modulation: 3 */
#define UCBRS_4             (0x08)    /* USCI Second Stage Modulation: 4 */
#define UCBRS_5             (0x0A)    /* USCI Second Stage Modulation: 5 */
#define UCBRS_6             (0x0C)    /* USCI Second Stage Modulation: 6 */
#define UCBRS_7             (0x0E)    /* USCI Second Stage Modulation: 7 */

/* UCAxSTAT Control Bits */
#define UCLISTEN            (0x80)    /* USCI Listen mode */
#define UCFE                (0x40)    /* USCI Frame Error Flag */
#define UCOE                (0x20)    /* USCI Overrun Error Flag */
#define UCPE                (0x10)    /* USCI Parity Error Flag */
#define UCBRK               (0x08)    /* USCI Break received */
#define UCRXERR             (0x04)    /* USCI RX Error Flag */
#define UCADDR              (0x02)    /* USCI Address received Flag */
#define UCBUSY              (0x01)    /* USCI Busy Flag */
#define UCIDLE              (0x02)    /* USCI Idle line detected Flag */


/* UCBxSTAT Control Bits */
#define UCSCLLOW            (0x40)    /* SCL low */
#define UCGC                (0x20)    /* General Call address received Flag */
#define UCBBUSY             (0x10)    /* Bus Busy Flag */

/* UCAxIRTCTL Control Bits */
#define UCIRTXPL5           (0x80)    /* IRDA Transmit Pulse Length 5 */
#define UCIRTXPL4           (0x40)    /* IRDA Transmit Pulse Length 4 */
#define UCIRTXPL3           (0x20)    /* IRDA Transmit Pulse Length 3 */
#define UCIRTXPL2           (0x10)    /* IRDA Transmit Pulse Length 2 */
#define UCIRTXPL1           (0x08)    /* IRDA Transmit Pulse Length 1 */
#define UCIRTXPL0           (0x04)    /* IRDA Transmit Pulse Length 0 */
#define UCIRTXCLK           (0x02)    /* IRDA Transmit Pulse Clock Select */
#define UCIREN              (0x01)    /* IRDA Encoder/Decoder enable */

/* UCAxIRRCTL Control Bits */
#define UCIRRXFL5           (0x80)    /* IRDA Receive Filter Length 5 */
#define UCIRRXFL4           (0x40)    /* IRDA Receive Filter Length 4 */
#define UCIRRXFL3           (0x20)    /* IRDA Receive Filter Length 3 */
#define UCIRRXFL2           (0x10)    /* IRDA Receive Filter Length 2 */
#define UCIRRXFL1           (0x08)    /* IRDA Receive Filter Length 1 */
#define UCIRRXFL0           (0x04)    /* IRDA Receive Filter Length 0 */
#define UCIRRXPL            (0x02)    /* IRDA Receive Input Polarity */
#define UCIRRXFE            (0x01)    /* IRDA Receive Filter enable */

/* UCAxABCTL Control Bits */
//#define res               (0x80)    /* reserved */
//#define res               (0x40)    /* reserved */
#define UCDELIM1            (0x20)    /* Break Sync Delimiter 1 */
#define UCDELIM0            (0x10)    /* Break Sync Delimiter 0 */
#define UCSTOE              (0x08)    /* Sync-Field Timeout error */
#define UCBTOE              (0x04)    /* Break Timeout error */
//#define res               (0x02)    /* reserved */
#define UCABDEN             (0x01)    /* Auto Baud Rate detect enable */

/* UCBxI2COA Control Bits */
#define UCGCEN              (0x8000)  /* I2C General Call enable */
#define UCOA9               (0x0200)  /* I2C Own Address 9 */
#define UCOA8               (0x0100)  /* I2C Own Address 8 */
#define UCOA7               (0x0080)  /* I2C Own Address 7 */
#define UCOA6               (0x0040)  /* I2C Own Address 6 */
#define UCOA5               (0x0020)  /* I2C Own Address 5 */
#define UCOA4               (0x0010)  /* I2C Own Address 4 */
#define UCOA3               (0x0008)  /* I2C Own Address 3 */
#define UCOA2               (0x0004)  /* I2C Own Address 2 */
#define UCOA1               (0x0002)  /* I2C Own Address 1 */
#define UCOA0               (0x0001)  /* I2C Own Address 0 */

/* UCBxI2COA Control Bits */
#define UCOA7_L             (0x0080)  /* I2C Own Address 7 */
#define UCOA6_L             (0x0040)  /* I2C Own Address 6 */
#define UCOA5_L             (0x0020)  /* I2C Own Address 5 */
#define UCOA4_L             (0x0010)  /* I2C Own Address 4 */
#define UCOA3_L             (0x0008)  /* I2C Own Address 3 */
#define UCOA2_L             (0x0004)  /* I2C Own Address 2 */
#define UCOA1_L             (0x0002)  /* I2C Own Address 1 */
#define UCOA0_L             (0x0001)  /* I2C Own Address 0 */

/* UCBxI2COA Control Bits */
#define UCGCEN_H            (0x0080)  /* I2C General Call enable */
#define UCOA9_H             (0x0002)  /* I2C Own Address 9 */
#define UCOA8_H             (0x0001)  /* I2C Own Address 8 */

/* UCBxI2CSA Control Bits */
#define UCSA9               (0x0200)  /* I2C Slave Address 9 */
#define UCSA8               (0x0100)  /* I2C Slave Address 8 */
#define UCSA7               (0x0080)  /* I2C Slave Address 7 */
#define UCSA6               (0x0040)  /* I2C Slave Address 6 */
#define UCSA5               (0x0020)  /* I2C Slave Address 5 */
#define UCSA4               (0x0010)  /* I2C Slave Address 4 */
#define UCSA3               (0x0008)  /* I2C Slave Address 3 */
#define UCSA2               (0x0004)  /* I2C Slave Address 2 */
#define UCSA1               (0x0002)  /* I2C Slave Address 1 */
#define UCSA0               (0x0001)  /* I2C Slave Address 0 */

/* UCBxI2CSA Control Bits */
#define UCSA7_L             (0x0080)  /* I2C Slave Address 7 */
#define UCSA6_L             (0x0040)  /* I2C Slave Address 6 */
#define UCSA5_L             (0x0020)  /* I2C Slave Address 5 */
#define UCSA4_L             (0x0010)  /* I2C Slave Address 4 */
#define UCSA3_L             (0x0008)  /* I2C Slave Address 3 */
#define UCSA2_L             (0x0004)  /* I2C Slave Address 2 */
#define UCSA1_L             (0x0002)  /* I2C Slave Address 1 */
#define UCSA0_L             (0x0001)  /* I2C Slave Address 0 */

/* UCBxI2CSA Control Bits */
#define UCSA9_H             (0x0002)  /* I2C Slave Address 9 */
#define UCSA8_H             (0x0001)  /* I2C Slave Address 8 */

/* UCAxIE Control Bits */
#define UCTXIE              (0x0002)  /* USCI Transmit Interrupt Enable */
#define UCRXIE              (0x0001)  /* USCI Receive Interrupt Enable */

/* UCBxIE Control Bits */
#define UCNACKIE            (0x0020)  /* NACK Condition interrupt enable */
#define UCALIE              (0x0010)  /* Arbitration Lost interrupt enable */
#define UCSTPIE             (0x0008)  /* STOP Condition interrupt enable */
#define UCSTTIE             (0x0004)  /* START Condition interrupt enable */
#define UCTXIE              (0x0002)  /* USCI Transmit Interrupt Enable */
#define UCRXIE              (0x0001)  /* USCI Receive Interrupt Enable */

/* UCAxIFG Control Bits */
#define UCTXIFG             (0x0002)  /* USCI Transmit Interrupt Flag */
#define UCRXIFG             (0x0001)  /* USCI Receive Interrupt Flag */

/* UCBxIFG Control Bits */
#define UCNACKIFG           (0x0020)  /* NAK Condition interrupt Flag */
#define UCALIFG             (0x0010)  /* Arbitration Lost interrupt Flag */
#define UCSTPIFG            (0x0008)  /* STOP Condition interrupt Flag */
#define UCSTTIFG            (0x0004)  /* START Condition interrupt Flag */
#define UCTXIFG             (0x0002)  /* USCI Transmit Interrupt Flag */
#define UCRXIFG             (0x0001)  /* USCI Receive Interrupt Flag */

/* USCI Definitions */
#define USCI_NONE           (0x0000)    /* No Interrupt pending */
#define USCI_UCRXIFG        (0x0002)    /* USCI UCRXIFG */
#define USCI_UCTXIFG        (0x0004)    /* USCI UCTXIFG */
#define USCI_I2C_UCALIFG    (0x0002)    /* USCI I2C Mode: UCALIFG */
#define USCI_I2C_UCNACKIFG  (0x0004)    /* USCI I2C Mode: UCNACKIFG */
#define USCI_I2C_UCSTTIFG   (0x0006)    /* USCI I2C Mode: UCSTTIFG*/
#define USCI_I2C_UCSTPIFG   (0x0008)    /* USCI I2C Mode: UCSTPIFG*/
#define USCI_I2C_UCRXIFG    (0x000A)    /* USCI I2C Mode: UCRXIFG */
#define USCI_I2C_UCTXIFG    (0x000C)    /* USCI I2C Mode: UCTXIFG */

/************************************************************
* USCI A1
************************************************************/
#define __MSP430_HAS_USCI_A1__       /* Definition to show that Module is available */

#define UCA1CTLW0_            0x0600    /* USCI A1 Control Word Register 0 */
sfrb(UCA1CTLW0_L, UCA1CTLW0_);
sfrb(UCA1CTLW0_H, UCA1CTLW0_+1);
sfrw(UCA1CTLW0, UCA1CTLW0_);
#define UCA1CTL1            UCA1CTLW0_L  /* USCI A1 Control Register 1 */
#define UCA1CTL0            UCA1CTLW0_H  /* USCI A1 Control Register 0 */
#define UCA1BRW_              0x0606    /* USCI A1 Baud Word Rate 0 */
sfrb(UCA1BRW_L, UCA1BRW_);
sfrb(UCA1BRW_H, UCA1BRW_+1);
sfrw(UCA1BRW, UCA1BRW_);
#define UCA1BR0             UCA1BRW_L /* USCI A1 Baud Rate 0 */
#define UCA1BR1             UCA1BRW_H /* USCI A1 Baud Rate 1 */
#define UCA1MCTL_             0x0608    /* USCI A1 Modulation Control */
sfrb(UCA1MCTL, UCA1MCTL_);
#define UCA1STAT_             0x060A    /* USCI A1 Status Register */
sfrb(UCA1STAT, UCA1STAT_);
#define UCA1RXBUF_            0x060C    /* USCI A1 Receive Buffer */
const_sfrb(UCA1RXBUF, UCA1RXBUF_);
#define UCA1TXBUF_            0x060E    /* USCI A1 Transmit Buffer */
sfrb(UCA1TXBUF, UCA1TXBUF_);
#define UCA1ABCTL_            0x0610    /* USCI A1 LIN Control */
sfrb(UCA1ABCTL, UCA1ABCTL_);
#define UCA1IRCTL_            0x0612    /* USCI A1 IrDA Transmit Control */
sfrb(UCA1IRCTL_L, UCA1IRCTL_);
sfrb(UCA1IRCTL_H, UCA1IRCTL_+1);
sfrw(UCA1IRCTL, UCA1IRCTL_);
#define UCA1IRTCTL          UCA1IRCTL_L  /* USCI A1 IrDA Transmit Control */
#define UCA1IRRCTL          UCA1IRCTL_H  /* USCI A1 IrDA Receive Control */
#define UCA1ICTL_             0x061C    /* USCI A1 Interrupt Enable Register */
sfrb(UCA1ICTL_L, UCA1ICTL_);
sfrb(UCA1ICTL_H, UCA1ICTL_+1);
sfrw(UCA1ICTL, UCA1ICTL_);
#define UCA1IE              UCA1ICTL_L  /* USCI A1 Interrupt Enable Register */
#define UCA1IFG             UCA1ICTL_H  /* USCI A1 Interrupt Flags Register */
#define UCA1IV_               0x061E    /* USCI A1 Interrupt Vector Register */
sfrw(UCA1IV, UCA1IV_);


/************************************************************
* USCI B1
************************************************************/
#define __MSP430_HAS_USCI_B1__        /* Definition to show that Module is available */


#define UCB1CTLW0_	0x0620    /* USCI B1 Control Word Register 0 */
sfrb(UCB1CTLW0_L, UCB1CTLW0_);
sfrb(UCB1CTLW0_H, UCB1CTLW0_+1);
sfrw(UCB1CTLW0, UCB1CTLW0_);
#define UCB1CTL1	UCB1CTLW0_L  /* USCI B1 Control Register 1 */
#define UCB1CTL0	UCB1CTLW0_H  /* USCI B1 Control Register 0 */
#define UCB1BRW_	0x0626    /* USCI B1 Baud Word Rate 0 */
sfrb(UCB1BRW_L, UCB1BRW_);
sfrb(UCB1BRW_H, UCB1BRW_+1);
sfrw(UCB1BRW, UCB1BRW_);
#define UCB1BR0		UCB1BRW_L /* USCI B1 Baud Rate 0 */
#define UCB1BR1		UCB1BRW_H /* USCI B1 Baud Rate 1 */
#define UCB1STAT_	0x062A    /* USCI B1 Status Register */
sfrb(UCB1STAT, UCB1STAT_);
#define UCB1RXBUF_	0x062C    /* USCI B1 Receive Buffer */
const_sfrb(UCB1RXBUF, UCB1RXBUF_);
#define UCB1TXBUF_	0x062E    /* USCI B1 Transmit Buffer */
sfrb(UCB1TXBUF, UCB1TXBUF_);
#define UCB1I2COA_	0x0630    /* USCI B1 I2C Own Address */
sfrb(UCB1I2COA_L, UCB1I2COA_);
sfrb(UCB1I2COA_H, UCB1I2COA_+1);
sfrw(UCB1I2COA, UCB1I2COA_);
#define UCB1I2CSA_	0x0632    /* USCI B1 I2C Slave Address */
sfrb(UCB1I2CSA_L, UCB1I2CSA_);
sfrb(UCB1I2CSA_H, UCB1I2CSA_+1);
sfrw(UCB1I2CSA, UCB1I2CSA_);
#define UCB1ICTL_	0x063C    /* USCI B1 Interrupt Enable Register */
sfrb(UCB1ICTL_L, UCB1ICTL_);
sfrb(UCB1ICTL_H, UCB1ICTL_+1);
sfrw(UCB1ICTL, UCB1ICTL_);
#define UCB1IE		UCB1ICTL_L  /* USCI B1 Interrupt Enable Register */
#define UCB1IFG		UCB1ICTL_H  /* USCI B1 Interrupt Flags Register */
#define UCB1IV_		0x063E    /* USCI B1 Interrupt Vector Register */
sfrw(UCB1IV, UCB1IV_);

/************************************************************
* WATCHDOG TIMER A
************************************************************/
#define __MSP430_HAS_WDT_A__          /* Definition to show that Module is available */

#define WDTCTL_		0x015C    /* Watchdog Timer Control */
sfrb(WDTCTL_L, WDTCTL_);
sfrb(WDTCTL_H, WDTCTL_+1);
sfrw(WDTCTL, WDTCTL_);
/* The bit names have been prefixed with "WDT" */
/* WDTCTL Control Bits */
#define WDTIS0		0x0001  /* WDT - Timer Interval Select 0 */
#define WDTIS1		0x0002  /* WDT - Timer Interval Select 1 */
#define WDTIS2		0x0004  /* WDT - Timer Interval Select 2 */
#define WDTCNTCL	0x0008  /* WDT - Timer Clear */
#define WDTTMSEL	0x0010  /* WDT - Timer Mode Select */
#define WDTSSEL0	0x0020  /* WDT - Timer Clock Source Select 0 */
#define WDTSSEL1	0x0040  /* WDT - Timer Clock Source Select 1 */
#define WDTHOLD		0x0080  /* WDT - Timer hold */

/* WDTCTL Control Bits */
#define WDTIS0_L	0x0001  /* WDT - Timer Interval Select 0 */
#define WDTIS1_L	0x0002  /* WDT - Timer Interval Select 1 */
#define WDTIS2_L	0x0004  /* WDT - Timer Interval Select 2 */
#define WDTCNTCL_L	0x0008  /* WDT - Timer Clear */
#define WDTTMSEL_L	0x0010  /* WDT - Timer Mode Select */
#define WDTSSEL0_L	0x0020  /* WDT - Timer Clock Source Select 0 */
#define WDTSSEL1_L	0x0040  /* WDT - Timer Clock Source Select 1 */
#define WDTHOLD_L	0x0080  /* WDT - Timer hold */

/* WDTCTL Control Bits */

#define WDTPW		0x5A00

#define WDTIS_0		(0U*0x0001)  /* WDT - Timer Interval Select: /2G */
#define WDTIS_1		(1U*0x0001)  /* WDT - Timer Interval Select: /128M */
#define WDTIS_2		(2U*0x0001)  /* WDT - Timer Interval Select: /8192k */
#define WDTIS_3		(3U*0x0001)  /* WDT - Timer Interval Select: /512k */
#define WDTIS_4		(4U*0x0001)  /* WDT - Timer Interval Select: /32k */
#define WDTIS_5		(5U*0x0001)  /* WDT - Timer Interval Select: /8192 */
#define WDTIS_6		(6U*0x0001)  /* WDT - Timer Interval Select: /512 */
#define WDTIS_7		(7U*0x0001)  /* WDT - Timer Interval Select: /64 */
#define WDTIS__2G	(0U*0x0001)  /* WDT - Timer Interval Select: /2G */
#define WDTIS__128M	(1U*0x0001)  /* WDT - Timer Interval Select: /128M */
#define WDTIS__8192K	(2U*0x0001)  /* WDT - Timer Interval Select: /8192k */
#define WDTIS__512K	(3U*0x0001)  /* WDT - Timer Interval Select: /512k */
#define WDTIS__32K	(4U*0x0001)  /* WDT - Timer Interval Select: /32k */
#define WDTIS__8192	(5U*0x0001)  /* WDT - Timer Interval Select: /8192 */
#define WDTIS__512	(6U*0x0001)  /* WDT - Timer Interval Select: /512 */
#define WDTIS__64	(7U*0x0001)  /* WDT - Timer Interval Select: /64 */

#define WDTSSEL_0	(0U*0x0020)  /* WDT - Timer Clock Source Select: SMCLK */
#define WDTSSEL_1	(1U*0x0020)  /* WDT - Timer Clock Source Select: ACLK */
#define WDTSSEL_2	(2U*0x0020)  /* WDT - Timer Clock Source Select: VLO_CLK */
#define WDTSSEL_3	(3U*0x0020)  /* WDT - Timer Clock Source Select: reserved */
#define WDTSSEL__SMCLK	(0U*0x0020)  /* WDT - Timer Clock Source Select: SMCLK */
#define WDTSSEL__ACLK	(1U*0x0020)  /* WDT - Timer Clock Source Select: ACLK */
#define WDTSSEL__VLO	(2U*0x0020)  /* WDT - Timer Clock Source Select: VLO_CLK */


/* WDT-interval times [1ms] coded with Bits 0-2 */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MDLY_32	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2)                         /* 32ms interval (default) */
#define WDT_MDLY_8	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTIS0)                  /* 8ms     " */
#define WDT_MDLY_0_5	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTIS1)                  /* 0.5ms   " */
#define WDT_MDLY_0_064	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTIS1+WDTIS0)           /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ADLY_1000	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTSSEL0)                /* 1000ms  " */
#define WDT_ADLY_250	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTSSEL0+WDTIS0)         /* 250ms   " */
#define WDT_ADLY_16	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTSSEL0+WDTIS1)         /* 16ms    " */
#define WDT_ADLY_1_9	(WDTPW+WDTTMSEL+WDTCNTCL+WDTIS2+WDTSSEL0+WDTIS1+WDTIS0)  /* 1.9ms   " */
/* Watchdog mode -> reset after expired time */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MRST_32	(WDTPW+WDTCNTCL+WDTIS2)                                  /* 32ms interval (default) */
#define WDT_MRST_8	(WDTPW+WDTCNTCL+WDTIS2+WDTIS0)                           /* 8ms     " */
#define WDT_MRST_0_5	(WDTPW+WDTCNTCL+WDTIS2+WDTIS1)                           /* 0.5ms   " */
#define WDT_MRST_0_064	(WDTPW+WDTCNTCL+WDTIS2+WDTIS1+WDTIS0)                    /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ARST_1000	(WDTPW+WDTCNTCL+WDTSSEL0+WDTIS2)                         /* 1000ms  " */
#define WDT_ARST_250	(WDTPW+WDTCNTCL+WDTSSEL0+WDTIS2+WDTIS0)                  /* 250ms   " */
#define WDT_ARST_16	(WDTPW+WDTCNTCL+WDTSSEL0+WDTIS2+WDTIS1)                  /* 16ms    " */
#define WDT_ARST_1_9	(WDTPW+WDTCNTCL+WDTSSEL0+WDTIS2+WDTIS1+WDTIS0)           /* 1.9ms   " */


/************************************************************
* TLV Descriptors
************************************************************/
#define __MSP430_HAS_TLV__              /* Definition to show that Module is available */

#define TLV_START	0x1A08    /* Start Address of the TLV structure */
#define TLV_END		0x1AFF    /* End Address of the TLV structure */

#define TLV_LDTAG	0x01      /*  Legacy descriptor (1xx, 2xx, 4xx families) */
#define TLV_PDTAG	0x02      /*  Peripheral discovery descriptor */
#define TLV_Reserved3	0x03      /*  Future usage */
#define TLV_Reserved4	0x04      /*  Future usage */
#define TLV_BLANK	0x05      /*  Blank descriptor */
#define TLV_Reserved6	0x06      /*  Future usage */
#define TLV_Reserved7	0x07      /*  Serial Number */
#define TLV_DIERECORD	0x08      /*  Die Record  */
#define TLV_ADCCAL	0x11      /*  ADC calibration */
#define TLV_REFCAL	0x12      /*  REF calibration */
#define TLV_TAGEXT	0xFE      /*  Tag extender */
#define TLV_TAGEND	0xFF      //  Tag End of Table


/************************************************************
* Interrupt Vectors (offset from 0xFF80)
************************************************************/


#define RTC_VECTOR		0x52	/* 0xFFD2 RTC */
#define PORT2_VECTOR		0x54	/* 0xFFD4 Port 2 */
#define TIMER2_A1_VECTOR	0x56	/* 0xFFD6 Timer0_A5 CC1-4, TA */
#define TIMER2_A0_VECTOR	0x58	/* 0xFFD8 Timer0_A5 CC0 */
#define USCI_B1_VECTOR		0x5A	/* 0xFFDA USCI B1 Receive/Transmit */
#define USCI_A1_VECTOR		0x5C	/* 0xFFDC USCI A1 Receive/Transmit */
#define PORT1_VECTOR		0x5E	/* 0xFFDE Port 1 */
#define TIMER1_A1_VECTOR	0x60	/* 0xFFE0 Timer1_A3 CC1-2, TA1 */
#define TIMER1_A0_VECTOR	0x62	/* 0xFFE2 Timer1_A3 CC0 */
#define DMA_VECTOR		0x64	/* 0xFFE4 DMA */
#define USB_UBM_VECTOR		0x66	/* 0xFFE6 USB Timer / cable event / USB reset */
#define TIMER0_A1_VECTOR	0x68	/* 0xFFE8 Timer0_A5 CC1-4, TA */
#define TIMER0_A0_VECTOR	0x6A	/* 0xFFEA Timer0_A5 CC0 */
#define ADC12_VECTOR		0x6C	/* 0xFFEC ADC */
#define USCI_B0_VECTOR		0x6E	/* 0xFFEE USCI B0 Receive/Transmit */
#define USCI_A0_VECTOR		0x70	/* 0xFFF0 USCI A0 Receive/Transmit */
#define WDT_VECTOR		0x72	/* 0xFFF2 Watchdog Timer */
#define TIMER0_B1_VECTOR	0x74	/* 0xFFF4 Timer0_B7 CC1-6, TB */
#define TIMER0_B0_VECTOR	0x76	/* 0xFFF6 Timer0_B7 CC0 */
#define COMP_B_VECTOR		0x78	/* 0xFFF8 Comparator B */
#define UNMI_VECTOR		0x7A	/* 0xFFFA User Non-maskable */
#define SYSNMI_VECTOR		0x7C	/* 0xFFFC System Non-maskable */
#define RESET_VECTOR		0x7E	/* 0xFFFE Reset [Highest Priority] */

/************************************************************
* End of Modules
************************************************************/

#endif /* #ifndef __msp430x552x */

Vorgefundene Kodierung: UTF-80