/*****************************************************************************
*
* Atmel Corporation
*
* File : main.c
* Compiler : AVR-GCC/avr-libc(>= 1.2.5)
* Revision : $Revision: 1.7 $
*
* Target platform : All AVRs with bootloader support
*
* AppNote : AVR109 - Self-programming
*
* Description : This Program allows an AVR with bootloader capabilities to
* Read/write its own Flash/EEprom. To enter Programming mode
* an input pin is checked. If this pin is pulled low, programming mode
* is entered. If not, normal execution is done from $0000
* "reset" vector in Application area.
*
* Preparations : Use the preprocessor.xls file for obtaining a customized
* defines.h file and linker-file code-segment definition for
* the device you are compiling for.
****************************************************************************/
#include "defines.h"
#include "serial.h"
#include "flash.h"
/* Uncomment the following to save code space */
// So geht's mit "avrdude -c avr109 -P com1 -b 9600" und es sind 7 KB frei
//#define REMOVE_AVRPROG_SUPPORT
//#define REMOVE_FUSE_AND_LOCK_BIT_SUPPORT
//#define REMOVE_BLOCK_SUPPORT
//#define REMOVE_EEPROM_BYTE_SUPPORT
//#define REMOVE_FLASH_BYTE_SUPPORT
#define ADDR_T unsigned int
#ifndef REMOVE_BLOCK_SUPPORT
/* BLOCKSIZE should be chosen so that the following holds: BLOCKSIZE*n = PAGESIZE, where n=1,2,3... */
# define BLOCKSIZE PAGESIZE
// this routine is placed to address 0 so it can be called
void __vectors(void) __attribute__((naked,noreturn));
void __vectors(void) {
asm volatile(
".org 0x1C00\n"
"clr __zero_reg__\n" // this address is the entry for boot loader (1KB)
"ldi r30,0x60\n" // initialize stack
"ldi r31,0x04\n"
"out 0x3E,r31\n" // SPH
"out 0x3D,r30\n" // SPL
"rjmp main\n"
);
}
void __do_copy_data(void) __attribute__((naked));
void __do_copy_data(void) {} // no non-zero-initialized static data
void __do_clear_bss(void) __attribute__((naked));
void __do_clear_bss(void) {} // no static data at all
static unsigned char BlockLoad(unsigned int size, unsigned char mem, ADDR_T *address) {
static unsigned char buffer[BLOCKSIZE];
unsigned int data;
ADDR_T tempaddress;
// EEPROM memory type.
if (mem=='E') {
/* Fill buffer first, as EEPROM is too slow to copy with UART speed */
for (tempaddress=0;tempaddress<size;tempaddress++) buffer[tempaddress] = recchar();
/* Then program the EEPROM */
_WAIT_FOR_SPM();
for (tempaddress=0; tempaddress<size; tempaddress++) {
EEAR = *address; // Setup EEPROM address
// EEARH = ((*address) >> 8);
EEDR = buffer[tempaddress]; // Get byte.
EECR |= (1<<EEMWE); // Write byte.
EECR |= (1<<EEWE);
while (EECR & (1<<EEWE)); // Wait for write operation to finish.
(*address)++; // Select next EEPROM byte
}
return '\r'; // Report programming OK
}else if (mem=='F') { // Flash memory type.
// NOTE: For flash programming, 'address' is given in words.
(*address) <<= 1; // Convert address to bytes temporarily.
tempaddress = *address; // Store address in page.
do {
data = recchar();
data |= (recchar() << 8);
_FILL_TEMP_WORD(*address,data);
(*address)+=2; // Select next word in memory.
size -= 2; // Reduce number of bytes to write by two.
}while (size); // Loop until all bytes written.
_PAGE_WRITE(tempaddress);
_WAIT_FOR_SPM();
_ENABLE_RWW_SECTION();
(*address) >>= 1; // Convert address back to Flash words again.
return '\r'; // Report programming OK
}else return '?';
}
static void BlockRead(unsigned int size, unsigned char mem, ADDR_T *address) {
// EEPROM memory type.
if (mem=='E') { // Read EEPROM
do{
EEAR = *address; // Setup EEPROM address
// EEARH = ((*address) >> 8);
(*address)++; // Select next EEPROM byte
EECR |= (1<<EERE); // Read EEPROM
sendchar(EEDR); // Transmit EEPROM dat ato PC
}while (--size); // Repeat until all block has been read
}else if (mem=='F') { // Flash memory type.
(*address) <<= 1; // Convert address to bytes temporarily.
do{
sendchar( _LOAD_PROGRAM_MEMORY(*address) );
sendchar( _LOAD_PROGRAM_MEMORY((*address)+1) );
(*address) += 2; // Select next word in memory.
size -= 2; // Subtract two bytes from number of bytes to read
}while (size); // Repeat until all block has been read
(*address) >>= 1; // Convert address back to Flash words again.
}
}
#endif /* REMOVE_BLOCK_SUPPORT */
void main(void) __attribute__((noreturn));
void main(void) {
ADDR_T address=0;
unsigned int temp_int=0;
unsigned char val;
/* Initialization */
initbootuart(); // Initialize UART.
/* Branch to bootloader or application code? */
if (!(PROGPIN & (1<<PROG_NO))) // If PROGPIN is pulled low, enter programming mode.
/* Main loop */
for(;;) {
val=recchar(); // Wait for command character.
// Check autoincrement status.
if (val=='a') sendchar('Y'); // Yes, we do autoincrement.
// Set address.
else if (val=='A') {// Set address...
// NOTE: Flash addresses are given in words, not bytes.
address=(recchar()<<8) | recchar(); // Read address high and low byte.
sendchar('\r'); // Send OK back.
}
// Chip erase.
else if (val=='e') {
for (address = 0; address < APP_END; address += PAGESIZE) {
// NOTE: Here we use address as a byte-address, not word-address, for convenience.
_WAIT_FOR_SPM();
_PAGE_ERASE(address);
}
sendchar('\r'); // Send OK back.
}
#ifndef REMOVE_BLOCK_SUPPORT
// Check block load support.
else if (val=='b') {
sendchar('Y'); // Report block load supported.
sendchar((BLOCKSIZE>>8) & 0xFF); // MSB first.
sendchar(BLOCKSIZE&0xFF); // Report BLOCKSIZE (bytes).
}else if (val=='B') { // Start block load.
temp_int = (recchar()<<8) | recchar(); // Get block size.
val = recchar(); // Get memtype.
sendchar(BlockLoad(temp_int,val,&address)); // Block load.
}else if (val=='g') { // Start block read.
temp_int = (recchar()<<8) | recchar(); // Get block size.
val = recchar(); // Get memtype
BlockRead(temp_int,val,&address); // Block read
}
#endif /* REMOVE_BLOCK_SUPPORT */
#ifndef REMOVE_FLASH_BYTE_SUPPORT
// Read program memory.
else if (val=='R') {
// Send high byte, then low byte of flash word.
_WAIT_FOR_SPM();
_ENABLE_RWW_SECTION();
sendchar( _LOAD_PROGRAM_MEMORY( (address << 1)+1 ) );
sendchar( _LOAD_PROGRAM_MEMORY( (address << 1)+0 ) );
address++; // Auto-advance to next Flash word.
}
// Write program memory, low byte.
else if (val=='c') { // NOTE: Always use this command before sending high byte.
temp_int=recchar(); // Get low byte for later _FILL_TEMP_WORD.
sendchar('\r'); // Send OK back.
}
// Write program memory, high byte.
else if (val=='C') {
temp_int |= (recchar()<<8); // Get and insert high byte.
_WAIT_FOR_SPM();
_FILL_TEMP_WORD( (address << 1), temp_int ); // Convert word-address to byte-address and fill.
address++; // Auto-advance to next Flash word.
sendchar('\r'); // Send OK back.
}
// Write page.
else if (val=='m') {
if (address >= (APP_END>>1)) sendchar('?'); // Protect bootloader area.
else{
_WAIT_FOR_SPM();
_PAGE_WRITE( address << 1 ); // Convert word-address to byte-address and write.
}
sendchar('\r'); // Send OK back.
}
#endif /* REMOVE_FLASH_BYTE_SUPPORT */
#ifndef REMOVE_EEPROM_BYTE_SUPPORT
// Write EEPROM memory.
else if (val=='D') {
_WAIT_FOR_SPM();
EEARL = address; // Setup EEPROM address.
EEARH = (address >> 8);
EEDR = recchar(); // Get byte.
EECR |= (1<<EEMWE); // Write byte.
EECR |= (1<<EEWE);
while (EECR & (1<<EEWE)); // Wait for write operation to finish.
address++; // Auto-advance to next EEPROM byte.
sendchar('\r');// Send OK back.
}
// Read EEPROM memory.
else if (val=='d') {
EEARL = address; // Setup EEPROM address.
EEARH = (address >> 8);
EECR |= (1<<EERE); // Read byte...
sendchar(EEDR); // ...and send it back.
address++; // Auto-advance to next EEPROM byte.
}
#endif /* REMOVE_EEPROM_BYTE_SUPPORT */
#ifndef REMOVE_FUSE_AND_LOCK_BIT_SUPPORT
// Write lockbits.
else if (val=='l') {
_WAIT_FOR_SPM();
_SET_LOCK_BITS( recchar() ); // Read and set lock bits.
sendchar('\r'); // Send OK back.
}
#if defined(_GET_LOCK_BITS)
// Read lock bits.
else if (val=='r') {
_WAIT_FOR_SPM();
sendchar(_GET_LOCK_BITS());
}
// Read fuse bits.
else if (val=='F') {
_WAIT_FOR_SPM();
sendchar(_GET_LOW_FUSES());
}
// Read high fuse bits.
else if (val=='N') {
_WAIT_FOR_SPM();
sendchar(_GET_HIGH_FUSES());
}
// Read extended fuse bits.
else if (val=='Q') {
_WAIT_FOR_SPM();
sendchar(_GET_EXTENDED_FUSES());
}
#endif /* defined(_GET_LOCK_BITS) */
#endif /* REMOVE_FUSE_AND_LOCK_BIT_SUPPORT */
#ifndef REMOVE_AVRPROG_SUPPORT
// Enter and leave programming mode.
else if ((val=='P')||(val=='L')) {
sendchar('\r'); // Nothing special to do, just answer OK.
}
// Exit bootloader.
else if (val=='E') {
UCSRA=0x40;
sendchar('\r');
while (!(UCSRA&0x40)); // await transmission completion
break;
}
// Get programmer type.
else if (val=='p') sendchar('S'); // Answer 'SERIAL'.
// Return supported device codes.
else if (val=='t') {
#if PARTCODE+0 > 0
sendchar( PARTCODE ); // Supports only this device, of course.
#endif /* PARTCODE */
sendchar( 0 ); // Send list terminator.
}
// Set LED, clear LED and set device type.
else if ((val=='x')||(val=='y')||(val=='T')) {
recchar(); // Ignore the command and it's parameter.
sendchar('\r'); // Send OK back.
}
#endif /* REMOVE_AVRPROG_SUPPORT */
// Return programmer identifier.
else if (val=='S') {
sendchar('A'); // Return 'AVRBOOT'.
sendchar('V'); // Software identifier (aka programmer signature) is always 7 characters.
sendchar('R');
sendchar('B');
sendchar('O');
sendchar('O');
sendchar('T');
}
// Return software version.
else if (val=='V') {
sendchar('1');
sendchar('5');
}
// Return signature bytes.
else if (val=='s') {
sendchar(SIGNATURE_BYTE_3);
sendchar(SIGNATURE_BYTE_2);
sendchar(SIGNATURE_BYTE_1);
}
// The last command to accept is ESC (synchronization).
else if (val!=0x1b) sendchar('?'); // If not ESC, then it is unrecognized...
}
_WAIT_FOR_SPM();
_ENABLE_RWW_SECTION();
__vectors(); // Jump to Reset vector 0x0000 in Application Section.
}
/* end of file */
| Detected encoding: UTF-8 | 0
|