Frequently Asked Questions (FAQ)

Why work USB to serial (RS232, COMx) converters well? And any commercial USB to parallel printer adapter not at all?

Most hardware attached to parallel port doesn't act like a printer, but is controlled by a self-made protocol. For example, not to disturb a printer behind a dongle.
There is no Windows function available to control dedicated pins of parallel port, therefore, the only choice for programmers is to directly access the hardware.

Serial ports are very well wrapped by Win32 functions, and it is very inconvenient for programmers to access a serial port directly. The two control lines (RTS and DTR) and the TxD line are easily controllable using EscapeCommFunction() function. The four status lines (CTS, DSR, DCD, RI) and the RxD line can be queried by GetCommModemStatus() function. This applies to old 16-bit Windows programs too — the Win16 API is similar.

Some programs are very slow when working with USB to serial converters. For example, simple PIC programmers.


How fast is this USB2LPT for my application?

How many bits per second are transferred using bit-banging depends heavily on your application. For following calculations, I assume USB high-speed.

The obvious limit is 8 kBit/s for read access (e.g. flash verify). Practically, the limit is roughly the half by Windows's driver design. If write access is written with USB2LPT or any other redirection in mind, it's still much faster. However, most apps check each clock and data bit they write, so the speed drops by factor 4 (even for write-only access), so we reach 1 kBit/s.
Even worse for JTAG because there are two data-out lines that are often checked independently. So it drops to 600 bit/s.
Often, software re-reads every written byte, to be extra sure, this halfs the data rate again. Therefore, expect no more than 0,5 .. 1 kBit/s transfer rates.

For example: avrdude (a popular command-line-driven Atmel AVR programmer software) needs 18 seconds to read an ATmega16 via parallel port. That is 7 kBit/s. Not very fast, but sufficient. With USB2LPT, it needs 6 minutes, that is 0,5 kBit/s. A good AVR project for those (larger) controllers have a bootloader, which is much faster and more convenient than programming via parallel port, so you often need USB2LPT only for “doping” the typical 1 KByte bootloader (which takes affordable 20 seconds via USB2LPT), or for some troubleshooting (and — in case of AVR — setting fuses).

Specialized software aware to USB2LPT (i.e. that uses the USB2LPT API) can be much faster, up to roughly 20 MByte/s, by replacing parts of the firmware in controller's RAM on-the-fly.


Can I use the USB2LPT.SYS driver with a regular (cheap) USB to parallel printer adapter?

Of course not! It's never possible due to design limitations of such adapters. See below.


Does USB2LPT work with Windows Vista / 7 / 8?

Yes. (Applies to 32 bit versions.)
Limitations for instant help may occur. You should install the .rtf-based .hlp file package from Microsoft:


Does USB2LPT work with multi-core architectures?

Yes. There may be blue-screen bugs, but most of them are removed November 2009, so don't forget to update the driver before reporting bugs.


Does USB2LPT work with X64 (AMD64) versions of any Windows?

Currently not well.
While there is a 64 bit driver available, it is not signed and does not feature the debug register redirection. Furthermore, the well-worked READ/WRITE_PORT_UCHAR redirection cannot work. There are simply no kernel functions to trap. However, the property sheet and the API is fully functional, so you can access the port pins with specialized software, e.g. my special build of inpout32.dll.

To install and use this driver, you must disable Driver Verification Enforcement at every startup. The procedure is:


What about parallel port software protection keys (hardlocks, dongles)?

This kind of devices don't work with USB2LPT. The only chance to get them to work is running a virtual machine (VMware or similar) and rewrite USB2LPT.SYS to a virtual machine driver.

You may have luck especially for some older software (last update before 1995), you can check whether you can record IN & OUT instructions with this Dongle Emulator. Note that this program runs on Windows 3.1, 3.11, 95, 98, Me and 2000, but not on XP and newer (it seems to work but it doesn't record anything), whereas USB2LPT works on newer systems too.


I like programming, or I have the source code, and I want to control some hardware (e.g. camera shutter, telescope positioner, LC display) with some output lines. Seems that USB2LPT is the perfect solution?

No, USB2LPT is not perfect, however, suitable. The disadvantages are:

For up to 3 output lines (and up to 5 input lines) it's quite perfect to use a serial port. USB→Serial adapters like this work seamlessly and — in many cases — fast enough. But note that mostly you have convert output voltages to TTL levels; for example with zener diodes 3.9 V. The maximum data rate via USB is 1000 level transitions per second.

For up to 8 output lines and 3 input lines, I recommend using a regular and cheap USB→Printer adapter, like this or this. However, the 5 V USB supply voltage is not available. The connection requires some circuitry, like this or this. The maximum data rate is about 100000 level transitions per second (even at multiple lines the same time, that's reasonably fast!), so it's perfect for controlling LEDs – or alphanumeric LC display controllers in nibble mode – or pixel graphics LC display controllers in serial mode or using a port expander. Many devices don't need inputs, e.g. stepper motors, serial D/A converters, or DDS frequency generators often used in ham radio applications.
The status lines ERR ⑮, ONL ⑬, and PE ⑫ can be read using DeviceIoControl(…,IOCTL_USBPRINT_GET_LPT_STATUS,…) with 1 kByte/s maximum speed. The INIT (16) line can only be controlled to output a LOW spike of some µs, nothing else, using DeviceIoControl(…,IOCTL_USBPRINT_SOFT_RESET,…). The remaining control and status lines STB ①, AF ⑭, SEL (17), ACK ⑩, and BUSY ⑪ are definitively not useable!
You get a handle to the USB→Printer adapter using this weird Win32-API code. It's much easier for Linux, simply open /dev/usb/lpn.

Unlimited output lines can be achieved using port expander circuits like 74HCT595, either attached to any parallel or serial port solution stated above.

For output and input lines and USB power (and built-in “brain”) you should use HID-based solutions like this or this or this.

For up to 2 (possibly also 6) output lines with precise timing control in microseconds pick your … sound card!! You have to solve DC clamping and amplification yourself, use operational amplifiers, comparators, possibly diodes and analog switches for this. The Win32 workhorse function for waveform output is waveOutWrite().


For CNC tool machines: Does USB2LPT support high step rates for stepper motors?

This problem requires deeper insight and explanation With this overwhelming advantages in mind, someone has to write a plugin for well-known MACH3 CNC software …

For the USB Microcontroller, IMHO, ARM7 based controllers are best suited, like NXP (former Philips) LPC214x or Atmel AT91SAM7S or AT32UC3B64 too.
The brand-new MSP430F55xx by Texas Instruments are not suited due to missing isochronous USB Pipes.
I will pick up this problem when I gather a CNC tool machine.

The theoretical maximum step frequency for USB2LPT (High Speed) is 4 kHz. The practical limit is 1 kHz.

For MACH3 there are specialized USB cards readily available — e.g. SmoothStepper — for high velocities. It's wise to use these solutions, the higher price is not for profit only. As stated above, such cards are informational nonsense because the downstream microstep controller converts the fast stepper pulses into slower coil current values.


For controlling LCD, someone recommends USB2LPT. Is this OK?

Generally, USB2LPT is suitable for LCD. Mostly you want to control a HD44780 compatible display controller. For controllerless displays, USB2LPT is not suited!

However, there are some issues to point to before deciding to use USB2LPT:
Hobbyists who are fraud programming microcontrollers should give USB→Printer adapters (see above) a try. Advantages: Disadvantage: The need to write a suitable PC-side software in Windows or Linux — until there grows a quasi-standard for hobbyists using those adapters.

Note by JGrosJean at ieee.org: “My low speed USB2LPT works in WinXP running on a virtual machine using Oracle VirtualBox in Linux.”


Would it be more convenient to use existing converters and use its built-in extern Prolific PL-2305 instead?

Photo of any USB to parallel converter
A usual parallel adapter (NOT my PCB!)

Those converters emulate extern USB printers according to extern USB device class code 7. The protocol used in printer class USB devices doesn't allow to set some printer port pins; that protocol doesn't know a parallel port at all. For compatibility reasons, »Paper End«, »Select«, and »Error« port statii may be requested, that's all. You can use such a device only and only if your external device is capable of EPP transfer, and you have to adapt your software. Most external devices need direct pin control.


Is there a chance to reprogram the PL-2305 chip?

Surely not. Those chips are mask-programmed, or maybe OTP (one-time programmable PROM).
Maybe there is a backdoor (undocumented features to access the pins directly), but that's hard to find out, if any available.

The PL-2305 has a backdoor. Its descriptor is as follows:
  • Device (string descriptors can be defined in EEPROM), Class »Multifunction«
    • Configuration Nr. 1
      • Interface Nr. 0
        • Alternate Setting Nr. 0
          Class: 07/01 = Drucker, Protocol: 01 = one direction
          • Endpoint Nr. 2, Bulk, Output, 64 Bytes
        • Alternate Setting Nr. 1
          Class: 07/01 = Drucker, Protocol: 02 = two directions
          • Endpoint Nr. 1, Bulk, Output, 64 Bytes
          • Endpoint Nr. 2, Bulk, Input, 64 Bytes
        • Alternate Setting Nr. 2
          Class: FF/00 = gusto, Protocol: FF = gusto
          • Endpoint Nr. 1, Bulk, Output, 64 Bytes
          • Endpoint Nr. 2, Bulk, Input, 64 Bytes
          • Endpoint Nr. 3, Interrupt, 4 Bytes, Interval: 1 ms
The »Alternate Setting Nr. 2« had no function. Probably, this is a IEEE 1284.4 protocol stub.


May it's possible to speed up the emulated IN instructions? (Even without changing software?)

If you are a great programmer, you may write an “on the fly disassembler” for the code following the IN instruction and look where the IN byte (AL register) is spread. After you get the true IN byte, you patch all locations where the IN byte is spreaded. Unluckily, most IN instructions are followed by a conditional jump, so you have to predict the condition... forget it!
On the other hand, it's easy to speed up REP INSB instructions. But these are seldom used in conjunction with ECP/EPP ports. With a standard parallel port, REP INSB is completely useless and therefore never used.


May it's possible to speed up changing the accessing software?

Yes, of course. You can concatenate IN instructions to two USB packets. You send data blocks, according to the documentation in this source code, to the converter, and get the answers in a multi-byte IN block.
Each instruction consumes about 1 µs. Delayed operation can be achieved using WAIT instructions (20h, thereafter the delay time in units of 4 µs) in the OUT packet. Slower delays you should achieve in software.

This converter (until Revision 1.1) has the following descriptor:
  • Device "USB2LPT Converter", Class »Multifunction«
    • Configuration Nr. 1
      • Interface Nr. 0
        • Alternate Setting Nr. 0
          Class: FF/FF = gusto, Protocol: FF = gusto
          • Endpoint Nr. 2, Bulk, Output, 64 Bytes
          • Endpoint Nr. 2, Bulk, Input, 64 Bytes
      • Interface Nr. 1
        • Alternate Setting Nr. 0
          Class: 07/01 = Printer, Protocol: 01 = one direction
          • Endpoint Nr. 4, Bulk, Output, 64 Bytes
        • Alternate Setting Nr. 1
          Class: 07/01 = Printer, Protocol: 02 = two directions
          • Endpoint Nr. 4, Bulk, Output, 64 Bytes
          • Endpoint Nr. 4, Bulk, Input, 64 Bytes
Such a two-interface device forms two devices. For this, Windows loads a “fork” driver, that itself loads two real drivers.

For more exact timing I advise you to “roll your own” and write your own 8051 program. You can download it anytime to the converter. [This converter is actually almost the same as an EZ-USB development board!]


For mass installation I want other default settings than those built-in into the USB2LPT.SYS file. How to do that? (Michael Ashman @ instron)

Modify the usb2lpt.inf file to include the following sections:
[Dev.ntx86.HW]
AddReg = usercfg_addreg

[usercfg_addreg]
HKR,,UserCfg,1,78,02,c8,00,06,03
This example sets the base address to 278h, timeout to 200 ms, and mode = ECP + EPP.

The number 1 after UserCfg declares following data as hex-binary. The data structure for these bytes has the following content (see source file usb2lpt.h):
struct USERCFG{
 USHORT LptBase; // trapped base address (EPP = base address + 4, ECP = base address + 0x400)
 USHORT TimeOut; // timeout value for write-back cache (both little-endian values)
 UCHAR flags;	 // OR-ed values of the following bits
#define UC_Debugreg	0x01	// Use debug register trap (one of four debug registers for every address range)
#define UC_Function	0x02	// Redirect kernel-mode access routines (READ_PORT_UCHAR etc.)
#define UC_WriteCache	0x04	// Enable write-back cache
#define UC_ReadCache0	0x08	// Enable read-ahead for base address+0
#define UC_ReadCache2	0x10	// Enable read-ahead for base address+2
#define UC_ReadCacheN	0x20	// Enable read-ahead for other registers (without effect)
#define UC_ForceRes	0x40	// unused
#define UC_ForceDebReg	0x80	// Force debug register usage even if used previously (Win98 problem)
 UCHAR Mode;	 // enum SPP,EPP,ECP,EPP+ECP
};


What about a version with a male SubD connector?

It's not possible to simply populate a male instead of the female SubD connector to the same PCB! This would lead to pin swappings like 1↔13, 2↔12 etc.
A complete PCB redesign would be necessary: Not worth at all while cheap “gender changers” are available.


What about a version with a 36-pin Centronics connector?

Do you know that 36-pin Centronics connectors are not contained in the latest parallel port standard?
A complete PCB redesign would be necessary: Not worth at all, use an ordinary printer cable.


Someone asks me if he can install two USB2LPT devices in one PC. I would guess not, since there is only one set of debug registers in a PC.

The instant help of USB2LPT's property sheet pages will answer this.

Every i86 and AMD64 compatible processor has four debug register sets. In case of SMP machines, this number remains the same because all processors must be programmed to halt on the same breakpoints (to be symmetrically). Indeed, the driver contains instructions to run specific code on one specific processor, that is scheduled in a small loop for all processors while the “main” (the calling) processor waits for completion of the others. It was somehow tricky but it works. There is no Windows Kernel API for doing this, but some API for helping: A deferred procedure call (DPC) with a hint to run on a specific processor. The current code doesn't support hot-swapping of processors, I have no machine to test this:-)

The USB2LPT.SYS driver consumes 1..3 debug register sets for each USB2LPT device, depending on emulation mode. For SPP mode (which is by far most-often sufficient), the minimum of 1 set covers all the 3 adjanced addresses, e.g. 0x378..0x37A. (To be true, it will cover 4 addresses, but the driver silently ignores the fourth address e.g. 0x37B.)

So, when using SPP only, four USB2LPT devices can be connected to one PC with hardware virtualization using debug register trapping method.

The driver itself currently limits devices to nine (not to have LPT10 or more). But the fifth device will not acquire debug register trap virtualization. The other type of virtualization, READ/WRITE_PORT_UCHAR/USHORT/ULONG, will be in effect for unlimited USB2LPT devices, so if you know your different accessing software a bit, you can assign redirection method to specific addresses and hence to specific applications. For Windows 9x/Me, this applies to the IOPM trap too. For AMD64 versions, unluckily, no READ/WRITE_PORT_UCHAR/USHORT/ULONG API exists, so only the debug register trap can ever work, but that's still hard to implement. Because there is driver certification enforcement in effect, there is only a handful of drivers available accessing port addresses. The well-known INPOUT32.DLL (or INPOUTX64.DLL) contains such certified drivers. The DLL code silently installs and loads (and unloads) that driver when the DLL is loaded or unloaded. So it's easy to make a replacement INPOUT32.DLL that “speaks” to USB2LPT device through its native interface, not needing any quirks like debug register trap.


Are enough devices available?

No, sold out.